Military Engineer Services Tender

Total amount of Sch 'A' Part-III (INTERNAL E/M SERVICES). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-IV (ROADS, PATH & CULVERT). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-V (EXTERNAL WATER SUPPLY). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-VI (EXTERNAL ELECTRIC SUPPLY). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-VII (EXTERNAL LIGHTENING PROTECTION). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-VIII (EXTERNAL SEWAGE DISPOSAL). Note: Details of prepriced schedule are given in tender documents.

Total amount of Sch 'A' Part-IX (EXTERNAL AREA DRAINAGE) Note: Details of prepriced schedule are given in tender documents.

Sch 'A' Part-X (MISCELLANEOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col 5 signifies this fact only.

Supply and fixing LED batten with surface/suspended lights fitting 1x 40W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

M&L for reconstruction of brick masonry valve pit of size 90cm x 90cm x 90cm (internal dimension) with one brick thick PCC 1:4:8 type D-2 (using 20mm graded crashed stone aggregate ) as in foundation concrete incl PCC (1:3:6) type Cl (using 20mm graded crashed stone aggregate) as in bedding and coping 10mm thick cement plaster in Cement mortar (1:4) internally & externally upto 15cm below ground level providing valve pit 50x50x6mm angle iron frame all round the fixed point by means of 4 Nos hold fast 150mm long made out of flat iron 40 x 6 mm embedded in PCC block (1:2:4) type B-I (using 20mm graded crashed stone aggregate) of size 230 x 200 x 100mm incl provn of hing welded with angle iron frame and Mild Steel cover 3mm thick, Mild steel handle of suitable and size welded with Mild steel cover & suitable locking arrangement & applying two coats of synthetic enamel paint over a coat of red-oxide primer incl necessary excavation work in soft/loss soil complete all as specified and directed.

Horizontal Boring for passing GI protection pipe up to 80 mm bore (dia), under road / foot path, not exc. 10.00 metre in a single length, complete all as specified and as directed.

S&F, composite polymer pin insulator, Length of thread on shank should be minimum 110 mm for 1 1 kV Pin insulator. Shank diameter is 20 mm for 11 kV Pin Insulator. Two Galvanised Iron Washers and One Galvanised Iron Nut for 11000 Volt Grade, complete all as specified and as directed.

Supply and Fix, composite polymer disc insulator,11 KV,creepage distance 340 mm,cantilever strength 70/90 kN,conforming to IEC: 61109,complete all as specified and directed. [Cat No. REE-PL-01-24F-11 of Make ‘Rashtriya’ or equivalent Model of Make ‘Jaipuria/BHEL/Supreme’]

Supply and fix cable route indicators as specified and as directed by engineer in charge

M&L for Indoor industrial factory made pedestal type cubical Feedar Pillar box of size 500x5000x400 mm made out of MS sheet 2.00 mm thick & surface provided by equal angle 50x50x5mm protection paneling for instrument/electrical items by 2mm thick MS sheet including surface painted with powder coated ionized spray paint by spraying including filling cavities of pillar, 2 coats of painting after primary coat (red oxide) , front and back opening with locking arrangement . Provision of danger notice board and the following electrical items including all connection , grouting etc. LT panel with following accessories :- Note:-Contractor should submit the drawing for approval of GE befor Procurement BUS BAR CHAMBER (a) TP&N solid anodized Aluminium bus bars, rated 200 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No.

INCOMER/ OUTGOING (a) MCCB, 4 Pole (Adjustable type), 100 Amps, 36 KA, 415 volt -01 Nos (Incomming) INDICATING DEVICES (b) LED Indicating lamps for Main Supply indicating R', Y' B' - Set of 3. (c) Digital Voltmeter (96mmx96mm) 0-500 Volt with selector switch of 10Amps -1No. (d) Current Transformer having Ratio 200/5, 5 VA rated burden - 3 Nos (Make: AE/RISHABH/L&T) (e) Digital Ammeter 0 to 400 Amps, square type (96mmx96mm) - 01 No. (Make: AE/RISHABH/CONZERV/L&T) (f) Voltmeter Selector switch (6A) 3 position with 'OFF' - 01 No. (Make : KAYCEE/L&T) (g) Ammeter Selector switch (6A) 3 position with 'OFF' - 01 No. (Make : KAYCEE/L&T)

M&L for Outdoor industrial factory made pedestal type cubical panel board of size 1500x1500x600 mm (LT Panel-01)made out of MS sheet 3.15mm thick & surface provided by equal angle 50x50x5mm protection paneling for instrument/electrical items by 2mm thick MS sheet including surface painted with powder coated ionized spray paint by spraying including filling cavities of pillar, 2 coats of painting after primary coat (red oxide) , front and back opening with locking arrangement . Provision of danger notice board and the following electrical items including all connection , grouting etc. LT panel with following accessories (Panel No 01) :- Note:-Contractor should submit the drawing for approval of GE befor Procurement BUS BAR (a) TP&N solid anodized Aluminium bus bars, rated 200 amps supported at required intervals sleeved with heat shrinkable PVC sleevings. The bars shall be colour coded at required intervals for identification - SET OF 4, 1 No. INCOMER a) MCCB, 4 Pole (Adjustable type), 100 Amps, 25 KA, 415 volt -01 Nos (Incomming)

OUTGOING FEEDERS b) MCCB, 4 Pole (Adjustable type), 415 volt 32 Amp 16KA -01 (For Bldg MCCB with enclosure ) c) MCCB, 4 Pole (Adjustable type), 415 volt 63 Amp 16KA -01 (For MT Equipment MCCB with enclosure ) d) MCCB, 4 Pole (Adjustable type), 415 volt 40 Amp 16 KA -02 (For Shelter Elect Load and For Spare) INDICATING DEVICES (a) LED Indicating lamps for Main Supply indicating R', Y' B' - Set of 3. (b) Digital Voltmeter (96mmx96mm) 0-500 Volt with selector switch of 10Amps -1No. (c) Current Transformer having Ratio 200/5, 5 VA rated burden - 3 Nos (Make: AE/RISHABH/L&T) (d) Digital Ammeter 0 to 400 Amps, square type (96mmx96mm) - 01 No. (Make: AE/RISHABH/CONZERV/L&T) (e) Voltmeter Selector switch (6A) 3 position with 'OFF' - 01 No. (Make : KAYCEE/L&T) (f) Ammeter Selector switch (6A) 3 position with 'OFF' - 01 No. (Make : KAYCEE/L&T)

Supply and fixing MCCB 32 Amps 4 Pole 16 KA 415 V of make Indoasian Cat No 830237 including MCCB Enclosure for 100A 4P MCCB of make indoasian Cat No 811987 fixed on wooden board of appropriate size for mounting of enclosure complete all as specified and as directed. Rate inclusive of Fixing of cable including lugging complete (For Buildg Electrical Load)

Supply and fixing MCCB 63 Amps 4 Pole 16 KA 415 V of make Indoasian Cat No 830240 including MCCB Enclosure for 63A 4P MCCB of make indoasian Cat No 811987 fixed on wooden board of appropriate size for mounting of enclosure complete all as specified and as directed. Rate inclusive of Fixing of cable including lugging complete (For MT Equipment Load)

Supply and fixing MCCB 40 Amps 4P 16 KA 415 Volt Make Indoasian Cat No 830238 including MCCB Enclosure for 40 Amp MCCB Make Indoasian Cat No 811987 fixed on wooden board of appropriate size for mounting of enclosure complete all as specified and as directed. Rate inclusive of Fixing of cable including lugging complete (For Shelter Electrical Load)

S & F 200 Watt LED ( CCT 5700 - 6500 K ), cradle / surface mounted Flood light made of aluminium die case housing with power coating, having excellent thermal management along with IP 66 protection with clamp as per site requirment complete all as specified and directed by Engr-in-charge. with efficiency of 110 lm/W and lumen output of >= 11000 lumen . Make :- Make :- Crompton (Cat No.- CFS-501-200-57-60D-SL-GL-NGG) or equiv make in PS.

LLDPE SEPTIC TANKS M&L for LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc. complete for 25 users

Construction of soakage wells excavation in any type of soil, returning filling of excavated soil and removing surplus soil exc 50 m but n exc 100 m, foundation over PCC 1:3:6, RCC column and RCC bend, walls of honey combed masonary and top wall one brick thick with top ring of M-25 concrete RCC cover slab interconnecting pipes required to carry of waste water in soakage wells complete filled with brick bats of 25 users complete all as specified and as directed. (Ref Drg No. AF/TD/STRU/236 Sheet No. 1/2 & 2/2. )