Military Engineer Services Tender

M&L for flat formwork of fair finsihed surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick for fair finished surfaces of concrete (Horizontal or sloping) complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for Mild steel bars 10mm dia and over(TMT bars FE-500 grade), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 7 here in before but 6mm to 8mm dia as in stirrups, spacers and binders all as directed

M&L for RCC M-25 Design mix (20 mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 Design Mix (20 mm aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 Design Mix (20 mm aggregate) as in Columns, pillars, piers, posts and struts all as specified and directed.

Material and labour for brick work with subclass B bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and direced

Material and labour for brick work with subclass B bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and direced

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil all as specified and directed.

Removing excavated material to a distance n.exc 50M and depositing where directed at a level n.exc 1.50M above the starting point complete all as specified and direced

Materials and labour for 10 mm thick rendering in cement mortar (1:6) on fair faces of brick/concrete surface,complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:4) on fair faces of brick/concrete surface finished even and smooth (without using extra lime or cement),complete all as specified and directed.

Materials and labour for 5 mm thick rendering in cement mortar (1:4) on fair faces of brick/concrete surface finished even and smooth (without using extra lime or cement),complete all as specified and directed.

M&L for hardcore of guage not exc 63mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface, complete all as specified and directed.

M&L for 100 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in sub base of floor complete all as specified and directed.

M&L for 75 mm thick Cement concrete type B-2, 1:2:4(40mm graded aggregate) as in path/ hard standing complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including Screed bed or bedding layer of mortar 15 mm thick (1:4) for laying floor finishes complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surface 300x 200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match as in skirting/ dados over and including 10 mm thick rendering even and rough in CM1:4 for backing of tiles, complete all as specified and directed.

Material and labour for 75mm thick PCC (1:2:4) type B2 as in plinth protection using 40mm graded stone aggregate, finishing cement concrete surface even and smooth without using extra cement, laid in alternate bays including filling of joints with mastic filling using one part of bitumen 80/100 grade mixed with three part of dry sand complete all as specified and directed.

M&L for Cement concrete C2 (1:3:6)( 40 mm aggregate) in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.complete all as specified and directed.

Water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top :- (a) Applying bitumenous primer @ 0.25 ltrs per Sqm over plastered surfaces of roof including parapet surface. (Note :- Bituminuous primer shall be "TANK MASTIC" manufactured by "EMUFALTE" manufactured by M/s Texsa India Ltd./STP) (b) Over the priming coat laying one layer of APP based polymembric membrane of approved manufacturer, 3 mm thick weight not less than 3.6 Kgs per Sqm reinforced with non woven polyester febric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 60cm (min) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note :- (i) Laying APP bassed polymenic membrane shall be done with torch application method or as per manufacturer's instructions. (ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints with suitable adhesive as per manufacturer's instruction. (iii) APP bassed polymeric membrane shall be "MOPLY FP 3MM" manufactured by M/S Texsa India Limited/STP. (iv) Applying two coats of Aluminium paint over APP membrane.)

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F 125X60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc made out of 1.25mm thick MS Sheet complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F sheet glass, 3mm thick ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 250mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed

S&F 100 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 100 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 100 mm butt hinges Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

M&L for Preparation fo new plastered surfaces of walls applying two coats of cement base paint over a coat of primer complete all directed

M&L for preparing new wall surfaces and applying two coat of oil bound distemper over chalk whitening all as specified and directed.

M&L for preparation of steel surfaces any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint (first quality ) over a coat of red oxide primer, complete all as specified and directed.

Manufacture and supply rifle rack for 20 rifle with chain all as shown on drawing Made out of 2nd class hard wood well seasoned, all exposed wooden surfaces shall be treated with two coats of synthetic enamel paint grey colour over a coat of pink primer and iron surface shall be painted with two coats of black synthetic enamel paint over a coat of red oxide primer complete all as shown on drawing and as directed. Note:The drawing for the rifle rack is not attached with the tender documents. These are available in the “STANDARD FURNITURE DESIGN BOOK” issued by Army HQ E-in-C’s branch, New Delhi that will be available for reference in all MES offices. The tenderer shall be deemed to have seen this drawing before receipt of the tender and shall be deemed to have quote their rates accordingly.

E/M WORKS:- Material and labour for point wiring with two single core PVC insulated & shathed copper conductor cable 1100 Volts grade FRLS size 1.5 Sqmm (nominal area) each drawn through and including stove enamelled steel conduit of suitable size (concealed) for flame proof wiring complete with flame proof accessories with one 1.5 sqmm single core PVC insulate solid copper conductor cable 1100 Volts grade FRLS as earth continuity wire, for one light point/fan point/bell point controlled by one flame proof switch complete all as specified and as directed.

Material and labour for point wiring with two single core PVC insulated & shathed copper conductor cable 1100 Volts grade FRLS of size 1.5 Sqmm (nominal area) each drawn through and including stove enamelled steel conduit of suitable size (concealed) for flame proof wiring complete with flame proof accessories with one 1.5 sqmm single core PVC insulate solid copper conductor cable 1100 Volts grade FRLS as earth continuity wire, for one flame proof 5 Amp Socket Point (Independent) controlled by one flame proof switch complete all as specified and as directed.

Material and labour for point wiring with two single core PVC insulated & shathed copper conductor cable 1100 Volts grade FRLS of size 1.5 Sqmm (nominal area) each drawn through and including stove enamelled steel conduit of suitable size for (concealed) flame proof wiring complete with flame proof accessories with one 1.5 sqmm single core PVC insulate solid copper conductor cable 1100 Volts grade FRLS as earth continuity wire, for one flame proof 5 Amp on same board controlled by one flame proof switch complete all as specified and as directed.

Material and labour for point wiring with two single core PVC insulated & shathed copper conductor cable 1100 Volts grade FRLS of size 4.0 Sqmm (nominal area) each drawn through and including stove enamelled steel conduit of suitable size (concealed) for flame proof wiring complete with flame proof accessories with one 4.0 sqmm single core PVC insulate solid copper conductor cable 1100 Volts grade FRLS as earth continuity wire, for 15 Amp Power point controlled by one flame proof switch complete all as specified and as directed.

Supply and fix FLP/WP Switch/Isolator 10 Amps single pole for ON/OFF all as specified and directed.

S&F Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 6A, 250V, 2P+earth complete all as per specified and directed

Supply and fix flame proof fan regulator all as specified and directed

S&F Flame proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth complete all as per specified and directed

Supply and fixing LED light fitting 30 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum housing with heat resistant toughened glass, with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fix sheet metal enclosure MCB DB 8 way SPN double door suitable for 240 V fixed flused on walls including cutting wall and making good disturbed surfaces, provision of blanking plate as per requirement complete all as specified and directed

Supply and fix amp rating, 240V, 10KA 'C' curve miniature circuit breaker (MCB) current carrying capacity 32 Amp SPN in the MCB DB complete with connection testing complete all as specified and directed

Supply and fix MCB single pole of capacity upto 6-32 amps, 240 Volts C-curve with 10kA breaking capacity all as specified and as directed.

M&L for earthling complete with galvanized mild steel earth plate electrode 600x600x6mm thick buried directly in ground ( in vertical position ) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5mtr (B.G.L.) and connected to galvanized iron earth strip 25x6mm by means of bolts, nuts, check nuts and washer of galvanized iron including PCC(1:2:4) type B1 precast RCC cover slab with suitable handle made of 12mm round bar, including necessary excavation &earth work in any type of soil. 20mm dia med gde galvanized steel tube for watering with one end fixed with cast iron funnel and wire mesh, 40mmdia bore, light grade galvanized steel tubing up to 5 mtr length for drawing earth lead wire protection common salt, charcoal etc complete all as shown in EP No 5 of SSR Part 1 and testing on completion.

Supply and fix Metal Alarm Bell with Pilot Lamp, AC 230 volts, industrial type sound level 1KM, including all accessories and testing the bell and including push button/ ON button complete all as per specified and directed.

Supply, laying/ hanging and testing copper armoured electric power cables (heavy duty) 1100 Volts grade size 10.0 sq mm 2 core, hanging on existing pole with 4mm GI wire with suitable insulator and on wall surface with suitable clamp complete all as specified and directed by Engr-in-Charge.