Military Engineer Services Tender
... More
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 90,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_MES_703007_1Tender No
C/8821/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Returning filling including spreading, levelling and well ramming in layers not exceeding 25cm thick in soil complete all as specified and as directed.
82
-
-
... More
Removal of surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and as directed.
137
-
-
... More
M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.
110
-
-
... More
Laying only old common brick laid in trenches for LT cable protection with length of brick perpendicular to length of cable complete all as specified and as directed.
800
-
-
... More
Supplying and laying un-reinforced precast concrete cable cover, classClass LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and directed.
8976
-
-
... More
Supply, fabricate and fixing of clamp made of GI strip of size not less than 32 x 6mm (Fe 290, Gde E-165) for support of cable protection pipe of existing size from existing steel / RCC pole of any size by making hole to strip and fixed with suitable size nut bolt and washer etc complete all as specified and as directed.
50
-
-
... More
Supplying and laying synthetic rubber insulated mats for voltage upto 11 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m and thickness not less than 12mm complete all as specified and as directed.
5
-
-
... More
M&L for danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with MS clamps, bolts and nuts of approved size for LT, 20 x 15 cm size including taking down of old one complete all as specified and as directed.
5
-
-
... More
Taking down/out unserviceable UG Cables of any Cross Sectional Area and Connections including Bricks, GI Pipes, etc. of any descriptions, laid in Trenches and/or fixing with Walls/Poles including Segregating of Serviceable Materials viz Bricks, Cables, GI Pipes, etc. and keep in Safe custody for re-use, complete all as specified and as directed
Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
1970
-
-
... More
Laying only old serviceable XLPE insulated, armoured, nominal cross sectional area of main conductor , stranded aluminium conductor, 1100 volt grade, any size, 2/3.5/4 core, to be laid in trenches, under floors, through GI pipe complete all as specified and as directed.
100
-
-
... More
Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, nominal cross sectional area of main conductor 10 Sqmm, 2 core, stranded aluminium conductor,1100 Volt grade, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
200
-
-
... More
Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, nominal cross sectional area of main conductor 16 Sqmm, 2 core, stranded aluminium conductor, 1100 Volt grade, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
300
-
-
... More
Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, nominal cross sectional area of main conductor 16 Sqmm, 4 core, stranded aluminium conductor, 1100 Volt grade, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
100
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 25 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
220
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 35 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
200
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 50 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
100
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 70 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
250
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 95 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
250
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 180 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
150
-
-
... More
Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, nominal cross sectional area of main conductor 400 Sqmm, 3 core with reduced neutral conductor (3 1/2 Core), stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items.
(2) Excavation and earth work shall be measured and paid separately.
100
-
-
... More
M&L for stay assembly comprising of 7/8 SWG galvanised stay of standard wire of required length fixed to pole with and including galvanised flat iron clamps, bolts, nuts and washers etc including galvanised steel 14 mm dia, 400 mm long stay bow and GI stay plate of size 300 x 300 x 6 mm thick, thimble MS clamp made out of 50 x 6mm and loop insulators porcelain brown all as shown in EP No.1 of SSR part - I including all accessories and excavation, earth work and PCC work complete all as specified and as directed.
10
-
-
... More
Dismantling cross-arms of M.S. channel or angle sections etc. complete and stacking aside serviceable materials for re-use with in 50m and removing unserviceable materials from site of work complete all as specified and as directed.
2
-
-
... More
M&L for cross arms bracing supports clamps and back plates fabricated from structural steel sections including nuts, bolts & washers, welding, bending, cold or hot drilling holes for bolts in any shape or size as indicated or directed and including one coat of aluminium paint over one coat of red oxide zinc chrome primer, complete all as specified and as directed.
2
-
-
... More
Dismantling of insulators of any type from LT poles of any size and type and setting aside complete all as specified and as directed.
70
-
-
... More
Supply and fixing pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65mm dia suitable for 1100 volts grade complete all as specified and as directed.
40
-
-
... More
Supply and fixing shackle type, porcelain, insulator vitreous, white, brown or green, including galvanised mild steel, straps, washers, insulator bolts, washers and nuts, 100 mm height and 115 mm dia, size of strap 31 mm x 5 mm and bolt of 14mm dia, suitable for 1100 volts complete all as specified and as directed.
20
-
-
... More
Supply and fixing loop type porcelain vitreous white, brown or green insulator small size, with overall dimensions 65 x 90 mm, clearance of hole 16mm including one galvanised mild steel spindle, two galvanised iron washer and one galvanised iron nut, complete all as specified and directed
10
-
-
... More
M&L for cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in pole foundation, filling and mass concrete complete all as specified and as directed.
5
-
-
... More
M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in coping of pole including necessary form work for fair finish surfaces complete all as specified and as directed
2
-
-
... More
Dismantling/taking down old aluminium steel reinforced (ACSR) conductor of any size any type from LT overhead line including all jumper, cross arms, clamps, bolts, nuts etc and keeping serviceable materials in safe custody for reuse in the work complete all as specified and as directed
5
-
-
... More
Supply, fixing and stringing of aluminium conductor steel reinforced (ACSR) conductor of size (a) Squireel 6/1 x 2.11, (b) Weasel 6/1 x 2.59, (c) Rabbit 6/1 x 3.25 as suitable conforming to IS - 398 part- 4 of 1994 including binding, straining in LT over head line including all jumper connection and binding on insulator with new wire/aluminium tape complete all as specified and as directed.
5
-
-
... More
Restringing of old aluminium conductor steel reinforced (ACSR) or AAAC conductor of 4 wire line ( 3 phase and neutral) and make on LT 9 m long poles alongwith earth wire, including replacement of binding wire and aluminium taps reconnection, street light connections, service connections and binding to insulators with suitable size of new binding wire including prunning of tree branches 2 mtr all around OH LT line by means of pulley, rope etc complete all as specified and as directed.
Note : 04 Nos of ACSR or AAAC conductor shall be measured as one unit length.
600
-
-
... More
Restringing of old aluminium conductor steel reinforced (ACSR) or AAAC conductor of 2 wire line (single phase and neutral) and make on LT 9 m long poles alongwith earth wire, including replacement of binding wire and aluminium taps reconnection, street light connections, service connections and binding to insulators with suitable size of new binding wire including prunning of tree branches 2 mtr all around OH LT line by means of pulley, rope etc complete all as specified and as directed.
Note : 02 Nos of ACSR or AAAC conductor shall be measured as one unit length.
600
-
-
... More
Dismantling existing unserviceable GI earth wire, cradles of any type obtained from service feeder or distributor span complete all as specified and as directed.
Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.
1
-
-
... More
M&L for Galvanised steel wire 3.15 or 4mm dia (hexagonal/ rectangular ) used for cradles guarding, earthing suitable for LT/HT overhead line etc complete all as specified and as directed.
1
-
-
... More
S&F for PVC/fiber separator for LT over head line 1100 volts conductor 3/4 wire system, suitable for 2 conductor, in span without damaging the over head line including taking down old separator complete all as specified and as directed .
200
-
-
... More
S&F for PVC/fiber separator for LT over head line 1100 volts conductor 3/4 wire system, suitable for 4 conductor, in span without damaging the over head line including taking down old separator complete all as specified and as directed .
200
-
-
... More
Boring of holes horizontal for laying not less than 40mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed.
Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.
30
-
-
... More
M&L for 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors including taking down old unserviceable pipe alongwith all fixing accessories complete all as specified and as directed.
40
-
-
... More
M&L for 40 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor /road crossing /drain etc as in protection of UG cable complete to walls and ceilings or laid in floors including taking down old unserviceable complete all as specified and as directed.
40
-
-
... More
M&L for 50 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor /road crossing /drain etc as in protection of UG cable complete to walls and ceilings or laid in floors including taking down old unserviceable complete all as specified and as directed.
30
-
-
... More
M&L for 80 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor /road crossing /drain etc as in protection of UG cable complete to walls and ceilings or laid in floors including taking down old unserviceable complete all as specified and as directed.
12
-
-
... More
M&L for earthing complete with GI earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m below ground level with the top edge of earth plate at depth not less than 1.5m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @ 15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing the base in which pit cover rests made up of MS angle iron (Frame) complete as specified and as directed.
6
-
-
... More
M&L for earthing with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 32x6mm dia by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing including taking down old unserviceable complete all as specified and as directed.
24
-
-
... More
S&F in replacement of ampere meter with built in selector switch 0-400 Amps of deep size 96x96 mm with accuracy class 1.0, three phase and suitable CT (03 Nos) including taking down old unserviceable one complete all as specified and as directed.
2
-
-
... More
S&F in replacement of digital voltmeter with built in selector switch 0-500 volts of dia size 96x96 sqmm with accuracy class 1.0, 3 phase including taking down old unserviceable one complete all as specified and as directed.
2
-
-
... More
S&F CT & PT as per existing ratio at site which can suitably fixed in existing ammeter and voltmeter of LT electric panel at site complete all as specified and as directed.
2
-
-
... More
Dismantling /uprooting of LT/HT unserviceable pre-stressed concrete /steel poles of any size and shape and including taking out dismantled portion of poles embedded in ground after necessary demolition of concrete foundation and making good disturbed ground surface properly and disposal thereof complete all as specified and as directed.
Note:- Earth work for taking out poles shall be measured and paid separately under relevant item of this Schedule.
10
-
-
... More
M&L for steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) including two coats of aluminium paint over a coat of primer except the planting depth which shall be painted with black bituminous paint including writing pole number using suitable paint complete all as specified and as directed. Note : excavation and earth work, PCC filling shall be measured and paid separately.
10
-
-
... More
Dismantling of lightning arresters any type/size for any capacity complete all as specified & directed.
1
-
-
... More
M&L for LT lighting arresters for outdoor, use, non-linear resistor type, horn gap and choking coil, maximum working pressure 1100 volts complete all as specified and as directed.
1
-
-
... More
S&F for 1100 volts grade, heavy duty, cable PVC insulated, aluminium conductor, stranded of size 10 Sqmm x 2 core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm dia GI suspension wire, one twin core cable flat or circular etc complete all as specified and as directed.
200
-
-
... More
S&F for On load change over switch 800 Amps with enclosure rated voltage 415V-AC 50 Hz, type FP fixed on wall with nut and bolt including taking down complete all as specified and directed.
1
-
-
... More
S&F for On load change over switch 100 Amps with enclosure rated voltage 415V-AC 50 Hz, type FP fixed on wall with nut and bolt including taking down complete all as specified and directed.
3
-
-
... More
S&F for On load change over switch 63 Amps with enclosure rated voltage 415V-AC 50 Hz, type FP fixed on wall with nut and bolt including taking down complete all as specified and directed.
2
-
-
... More
S&F in repair test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hexagonal head screw including removing the existing old unserviceable one complete all as specified and as directed.
1
-
-
... More
Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete
20
-
-
... More
Supply and fixing street light bracket made out of GI pipe (light grade) 40 mm dia 1.5 mtr long bent to required shape as directed and fixed to pole complete with and including two Nos. of M.S. flat 25mm x 4 mm clamps with necessary bolts, nuts and washers of suitable size complete all as specified and as directed by Engineer-in-Charge.
5
-
-
... More
Taking down existing old/ undserviceable MCCBs/ACB of any description from LT panel board complete all as specified and as directed.
9
-
-
... More
S&F for MCCB, 415 V, AC, 50 KA breaking capacity, 4 pole of rating 400 Amps, ices = icu=100% with adjustable thermal & fixed magnetic setting, 70-100% complete fixed with LT panel board all as specified and as directed.
1
-
-
... More
S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 250 Amps, ices = icu=100% with adjustable thermal & fixed magnetic setting, 70-100% complete fixed with LT panel board all as specified and as directed.
1
-
-
... More
S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 200 Amps, with adjustable thermal & fixed magnetic setting, complete fixed with LT panel board all as specified and as directed.
1
-
-
... More
S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 125 Amps, with adjustable thermal & fixed magnetic setting, complete fixed with LT panel board all as specified and as directed.
2
-
-
... More
S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 100 Amps, with adjustable thermal & fixed magnetic setting, complete fixed with LT panel board all as specified and as directed.
2
-
-
... More
S&F for MCCB, 415 V, AC, 36 KA breaking capacity, 4 pole of rating 63 Amps, with adjustable thermal & fixed magnetic setting, complete fixed with LT panel board all as specified and as directed.
1
-
-
... More
S&F in repair MCB, Single pole and neutral , 240 Volts, 6 to 32 Amps, 'C' series, 10KA capacity breaking capacity complete all as specified and directed,
6
-
-
... More
S&F in repair for galvenised iron strip 32 x 6 mm buried in ground complete all as specified and directed,
40
-
-
... More
S&F in heavy duty long life power capacitor (KVAR) of various capacity as per site requirement , 440 Volt AC complete all as specified and directed,
30
-
-
... More
Supply only water proof/submersible rubber insulation tape complete all as specififed and as directed.
1
-
-
... More
Supply only PVC insulation tape Box/ packet contain 9M roll 12 Nos in each Pack complete all as specified and directed.
2
-
-
... More
M&L for panel reparing and spray painting only external surfaces of dimension not exceeding 1.8 mx1.4 mx0.6 m to 1.0mx0.9mx0.6 m without taking down pannel accessoriesone and apply two coat of synthetic enamel paint over a coat of red oxide primer on steel surfaces including preparation of old surfaces of steel by scrapping, rubbing complete all as specified and as directed. .
5
-
-
... More
M&L for panel reparing by welding/ brazing etc making door to opening properly for any existing electrical panel complete all as specified and as directed.
1
-
-
... More
S&F in repair electric panel door lock of same type as per existing one with key complete all as specified and as directed.
2
-
-
... More
S&F resin type straight throught LT 1100 Volt cable joint kit of size 25- 50 Sqmm 4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
1
-
-
... More
S&F resin type straight throught LT 1100 Volt cable joint kit of size 70- 120 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
1
-
-
... More
S&F resin type straight throught LT 1100 Volt cable joint kit of size 150- 185 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
1
-
-
... More
S&F resin type straight throught LT 1100 Volt cable joint kit of size 300- 400 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
1
-
-
... More
S&F resin type End termination LT 1100 Volt cable joint kit of size 25- 50 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
1
-
-
... More
S&F resin type End termination LT 1100 Volt cable joint kit of size 70- 120 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
3
-
-
... More
S&F resin type End termination LT 1100 Volt cable joint kit of size 150- 185 Sqmm 3.5/4 Core complete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
3
-
-
... More
S&F resin type End termination LT 1100 Volt cable joint kit of size 300- 400 Sqmm 3.5/4 Corecomplete all as specified and as directed. Note: Only necessary earth work shall be measured and paid separately rest are included in unit quoted rate.
4
-
-
... More
S&F indication lamp set of three of colour Red, Yellow, and Blue for LT panel Board including takinf down old one complete all as specified and as directed.
1
-
-
... More
M&L for preparation of old painted surface and removing dust and other deposited material by scraping from LT PSC/steel tubular poles of upto 11.00 metre long, cross arms brackets and applying two coats of aluminium paint to all steel surfaces, including MS clamps, cable protection pipe, bracket fitted with street light fittings etc and one coat of cement based paint to PSC pole including Zebra colour of painting upto 2.1 m height from the top of coping/bottom of pole as per site condition and numbering of poles complete all as specified and as directed. Note :(a) Zebra colour will be applied by synthetic enamel paint of black/yellow colour as approved in alternate layer of 30 cm height of each layer.
(b) Pole number should be wrriten on each pole with preparation date.
100
-
-
... More
Supply installation, commissioning and testing including providing all necessary electrical connection, LT Junction box, outdoor type CPRI approved factory made out of 3.15 mm thick MS sheet of size 0.60mx 0.60 mx 0.50 m deep having hinge opening arrangement in front and back side and bottom frame made out of angle iron of size 50x50x6mm thick and 04 Nos legs 0.5 meter length with cable entry and exit circular hole with cable gland & gasket at bottom including painting to all internal and external exposed steel surfaces with powder coating paint (5 stage process) with duly fixed in ground with necessary PCC foundation (1:2:4) type B1, with danger notice plate, street light panel of 1.6mm thick mild steel sheet, vitereous enamelled (white), with letters, figures and conventional skull and bones in signal red colour, fixing lugs, bolts, screws etc including taking down Old unserviceable box complete all as directed by the Engr-in-Charge and comprising of the following accessoriescomplete including following accessories :-
(a) MCCB, 4 Pole, 200-250 Amps, 415 Volt, 36 KA I/C, with thermal and magnetic release.
(b) Aluminium bus bar 4 strip of 300 Amps of size 40 x 2.5mm having hole drilled on bus bar for fixing of cable
2
-
-
... More
Supply, install, testing and commissioning outdoor type LT panel of size 1.2m x 1.2m x 0.6m , CPRI approved factory made totally enclosed dust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and aluminium bus bar 500 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:- (Main Panel NO-I).
Note : Foundation to be included in the quoted price
Incoming :-
(a) MCCB, 4 Pole, 320 Amp, 415 V, 50 kA - 01 No (b) 3 Phase LED Voltmeter Cl-1
(c) Phase indicator lamps (RYB) -set of 3
(d) Aluminium bus bar 4 strip - 500 amps
(e) Internal connection by aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etc
Outgoing :-
(a) MCCB, 4 Pole, 160Amp, 415 V, 36 kA - 02 No (b) MCCB, 4 Pole, 80Amp, 415 V, 36 kA - 01 No (c) MCB,TPN, 63A, 240 V, 18 kA - 02 Nos. (For street light and 01 extra)
1
-
-
... More
Supply, install, testing and commissioning outdoor type LT panel of size 1m x 1m x 0.5m , CPRI approved factory made totally enclosed dust and vermin proof , double steef shutter in front and single leaf shutter in rear side made of 3.15 mm thick CRCA sheet, duly fabricated and having proper locking arrangement in both ront and rear door painted with powder coated paint and aluminium bus bar 200 amps suitable for 500 volts, 50 Hz , 3 phase 4 wire system and comprising with and including following accesories and mounted on PCC platform all around the panel board complete with the following items:-
Note : Foundation to be included in the quoted price
Incoming :-
(a) MCCB, 4 Pole, 125A, 415 V, 30 kA. (I/C).
(b) Phase indicator lamps (RYB) -set of 3
(c) Aluminium bus bar 4 strip -200 amps
(d) Internal connection by aluminium strip from mcb/mccb to busbar and busbar to mccb/mcb etc
Outgoing :-
(a) MCCB, 4 Pole, 100 Amp, 415 V, 30 kA - 01 No (b) MCB, TPN, 32 A, 240 V, 18 kA - 05 No.
4
-
-
... More
M&L for Hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface with Broken stone or boulders complete all as specified and as directed.
16
-
-
... More
M&L for 100mm thick PCC (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) as in flooring laid in panels finished even and smooth without using extra cement complete all as specified and directed.
150
-
-
... More
Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15cm thickness (below or above ground level) removing rubbish off the premises etc complete all as directed.
15
-
-
... More
M&L for 60mm thick Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 M-35 grade, laid as directed to any shape complete all as specified and as directed.
150
-
-
... More
Supply and fix for precast PCC cable route indicator duly marked and painted for HT/LT cables of size 80x25x7.5 cm with suitable size of base, embossed with lettering "MES HT Cable", complete all as specified and as directed.
55
-
-
... More
Supply and install Automatic Power Factor Correction (APFC) Panel for 3 Phase, 415 V & 50 Hz system of capacity 30 KVAR with incoming MCCBs of 63 A complete all as pecified and directed.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%