Indian Oil Corporation Limited Tender

Supply, Installation, Glanding, Testing & Commissioning of Flameproof 4 Way Junction Box (15 mm Dia) on Lighting Poles in Hazardous Area for looping of cables (Make: Baliga / FEPL / Flexpro / FCG) with double compression cable gland & lugs

Supply, Installation, Testing & Commissioning of 8 M Octagonal Pole 3 mm thick, Top A/F 70 mm, Bottom A/F 130 mm, Base Plate 200 x 200 x 16 mm Galvanized with flameproof Flood Light fixing plate (Make: CGL /Bajaj / Philips / Surya Roshni / Utkarsh India) Note: The civil works required for foundations shall also be part of the above works and shall not be measured separately.

Supply and erection, glanding, testing and commissioning of Dia Cast Aluminium Street light fittings with toughened glass 70 W LED lamp similar to Crompton Cat No. CRP-409-70-57-SL-GL-NSG or Bajaj ENXT P 54L WH PO PC SD MT for Street Lighting. (Make: CGL/Bajaj / Philips / Surya Roshni)

Supply, Installation, Testing & Commissioning of 8 M Octagonal Pole 3 mm thick, Top A/F 70 mm, Bottom A/F 130 mm, Base Plate 200 x 200 x 16 mm Galvanized with 1 M Single arm for Street light, Terminal Block and DP MCB with cable lugs (Make: CGL/Bajaj / Philips / Surya Roshni) Note: The civil works required for foundations shall also be part of the above works and shall not be measured separately.

Supply, Installation Glanding, Testing & Commissioning of specially designed pressure die cast housing with IP65 protection, heat resistant tempered glass 100 W LED flood light luminaries similar to Crompton Type CFS-504-100-57-60D-SL-GL-NSG Bajaj Type PRAZE F 120L WH NB-A5 TG SD at Fire Water Pump House (Make: CGL / Bajaj / Philips / Surya Roshni) with double compression cable gland & lugs

Supply and erection, glanding, testing and commissioning of Dia Cast Aluminium WP Well glass light fittings with toughened glass 45 W LED suitable for celling / wall mounting for Fire Water Pump House and DG Set Shed. (Make: CGL / Bajaj / Philips / Surya Roshni) with double compression cable gland & lugs

Supply, Installation, glanding, Testing & commissioning of 63 A SFU with 32 A Fuse and 32 A, 30 mA, 4P ELCB in vacant feeders of Lighting Panel with necessary modification and wiring etc (Make: L&T / Siemens / ABB / SCHNEIDER)

HIGH MAST- Supply, Installation, testing, commissioning of 30 Mtr. height High Mast suitable for 16 Nos. luminaires complete with accessories as per specification 4004007688-TS-101 Rev 0. The cost shall include supply and providing 3C X 2.5 mm² unarmoured copper cable from the junction box at the top of mast to lighting fixtures. The cost should also include supplying and providing trailing cable from FLP Switch Plug & Socket at the foot & FLP Power tool of high mast to the junction box at the top. (Make: CGL / Bajaj / Philips / Surya Roshni) Note- a) The civil works required for foundations shall also be part of the high mast works and shall not be measured separately. b) Lightening arrestor & aviation obstruction lamp shall also be provided as a part of supply of high mast c) Tenderers should note that junction box shall be provided at the top of the high mast and separate control gear boxes for light fittings d) For High Masts, tenderers to quote rates including design, supply and providing the foundations.

Design, supply, installation, glanding of flameproof type Feeder Pillar Box for the operation of the High Mast, 3 - Phase Motor, Reversible Starter and other accessories as per technical specification (4004008104-TS-101 Rev 0) (Make: Baliga / FEPL / Flexpro / FCG)

Supply, Installation Galndig, Testing & Commissioning of specially designed pressure die cast housing with IP65 protection, heat resistant toughened glass for protection with 10 KV surge protection 350 W LED flood light with 60° Beam Angle as per technical Specification (4004008104-TS-102 Rev 0) luminaries similar to Crompton Type CFS-512-350-57-60D-SL-GL-NSG or Bajaj PRAZE F 420L WH NB-A5 TG SD (Make: CGL / Bajaj / Philips / Surya Roshni) with double compression cable gland & lugs for Flood Light Towers, Old and New High Masts

PART - II: CABLE LAYING AND TERMINATION- Supplying of 1.1 KV grade XLPE insulated armoured aluminium / copper, FRLS cables as per Technical Specification (4004008104-TS-103 Rev 0) and horizontal and vertical laying as per Cables Schedule (4004008104-PCIS-115 Rev 0) of the following sizes in readymade concrete or soil trenches, trays, risers, support hangers, saddles etc, pulling through pipe on walls, floors and columns, steel structures including transportation from stores to site, unpacking, erection, dressing including supply and fixing of aluminium tags for identification of cable at both ends and at every 30 meter interval, providing GI saddles, saddle bars GI / Al clamps for cables laid vertically on walls / column / structures etc, GI bolts, nuts and washers complete with all labor, material and as per specification enclosed and direction of site in-charge. (Make: Polycab / CCI / KEI / RPG / Torrent / Universal / Havells / Gupta Power / GEMSCAB / Dynamic Cable) Note: a. The rate of Installation should be inclusive of Cable clamps, tags Saddles, Consumables etc. Trays/pipes, Glands, trenches, fabricated tray supports etc will be covered & paid in Separate Item. b. The necessary civil works shall be measured and paid separately under respective civil items. c. Tenderers to note that cables being dismantled and quantity already available at site shall be used in works at appropriate places and balance quantity as per site requirement shall be procured and supplied for completion of works. FRLS TYPE CABLE a)3½ C X 50 mm² (Al)

b)4 C X 16 mm² (AL)

c)4 C x 2.5 mm² (Cu)

FRLS TYPE CABLE (Copper)- Supply, laying, supporting, fixing, clamping with Aluminium clamps/ Nylon tie on structures and providing GI saddles on walls and RCC columns for supporting 3 X 2.5 mm² XLPE A FRLS PVC lighting cable from flameproof lighting. Lighting Distribution board / JBs to lighting fixture etc. This shall include supply of all material required for laying of cable including transportation of drum from store to erection site. Circuit numbering should be provided on cable by using aluminium cable tags and by paint on fixtures.

Cable Termination (NON FLP): Providing cable termination with supplied cable gland for the following cable with NON FLP nickel plated Brass double compression cable glands include supply crimping type, Al / Cu sockets, non-corrosive inhibitive paste, crimping etc. complete and as directed at site. a) 3½ C X 50 mm² (Al)

b)4 C X 16 mm² (AL)

C)4 C X 2.5 mm² (Cu)

d)3 C X 2.5 mm² (Cu)

Cable Termination (FLP): Providing cable termination with supplied cable gland for the following cable with FLP nickel plated Brass double compression cable glands, including supply of crimping type, Al / Cu sockets, non-corrosive inhibitive paste, crimping etc. complete and as directed at site. a) 3½ C X 50 mm² (Al)

b)4 C X 16 mm² (AL)

c)4 C X 2.5 mm² (Cu)

d)3 C X 2.5 mm² (Cu)

Supply, Installation & grouting of cable marker (route) with suitable engraving of voltage level along the cable route, at every bend of the trench and at every 30 M in straight run for identifying and locating the cables directly buried underground. The marker shall be of cast iron 5mm thick plate with arrow indicating the route of the cable. (Refer drg. no. GDE 1267 page 1 to 2) The concreting ratio for purpose of grouting shall be 1:2:4

PART- III: EARTHING AND LIGHTENING PROTECTION- Supply, installation, erection, testing and commissioning of GI earth electrode of 100 mm dia, 3.8 m long perforated pipe with necessary funnel etc complete as per drawing (PDS E604, PDS E605, PDS E610 & PDE E611 etc) enclosed. The Hot Dip Galvanizing (900 gm/M² as per IS-4759) shall be done after all fabrication. The Electrode shall be made from one pipe; however, 10 percent supply can be with one joint. The scope of work includes earthwork excavation, refilling with alternate layers of charcoal and salt, back filling and construction of brick masonry earth pit including plastering in CM 1:4 and supplying and providing a cover etc complete as per drawings & directions at site.

Supply and installation of hot dip galvanized GI earth bus (Galvanizing 900 gm/M²) as per drawing no PDS E615 Rev 1

Supply, laying, installation, connection by welding, testing and commissioning of hot dip galvanised earthing strip (900 gm/M² as per IS-4759) of the following sizes in excavated or RCC trenches along with cables including laying the flat for earthing or otherwise clamping where ever required, bitumen painting at the welded joints, connecting at both ends by making hole to earth pit / earth bus / equipment including supply of all hardware and consumables etc. as per drawing enclosed and as per directed by site in-charge. a) 50 mm X 6 mm (for main earth grid & connection of Earth Bus)

b)35 mm X 6 mm (for Feeder Pillar Box and Lighting fixture)

Supply and laying of the following sizes of 0.66/1.1 KV grade XLPE Insulated Aluminium Conductor Cable (multi-strand) for Earth connections as per 4004008104-TS-103 Rev 0 in Trenches, Floors, Hume Pipe, GI Pipe, Cable Trays, on Steel / Civil Structure with necessary cable lugs, G.I. Spacers and saddles etc. (Make: Polycab / CCI / KEI / RPG / Torrent / Universal / Havells / Gupta Power / GEMSCAB / Dynamic Cable) a)1C x 16 mm² A2XY (for LDB & lighting fixture earthing)

PART IV: MISCELLANEOUS AND CIVIL WORKS- Earth work in excavation in all kinds of soil by manual means in foundation trenches or drains including dressing of sides & ramming of bottom, lift up to 1.5 m, including getting out the excavated soil & disposal of surplus excavated soil as directed within or outside the site at an unobjectionable place.

Earth work in excavation in Ordinary rock by mechanical means (Hydraulic excavator) in foundation trenches or drains including dressing of sides & ramming of bottom, lift up to 1.5 m, including getting out the excavated soil & disposal of surplus excavated soil as directed within or outside the site at an unobjectionable place.

CABLE BRICK DUCT Providing & constructing underground brick duct 650mm below GL for laying of cables of max. diameter 70mm, complete with supply and laying of sand, bricks & including Excavation and backfilling in all kind of soils a)450 mm wide (24 Bricks & 0.0494 cum per Mtr) as per specifications and direction of Engineer in charge.

b)225 mm wide (16 Bricks & 0.0195 cum per Mtr) as per specifications and direction of Engineer in charge.

Supply, fabrication and installation of class B type GI pipe as per IS-1239 (part-1) of following sizes for cable protection, floor sleaves etc. fixed on steel structure, concretes, laid in trenches including cutting, bending, threading etc. as required, including supply of GI clamps, bolts, nuts and washers, complete with all labour and material as per the direction of site in-charge. a)50 mm N. B

Supply, providing and laying of 150 mm dia non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete: Light Duty of 0.07 MPa test pressure

Supply and fabrication and erection of various sizes of MS supports brackets, base frames, hangers, risers, racks, clamps etc. For different electrical equipment as and where required. The job will include cutting, drilling, welding, riveting, bolting, grouting, etc of Steel structural with two coats of epoxy base red oxide primer and two coats of epoxy paint (80 micron) shade 632 of IS-5 including supply of all consumables, necessary hard wares, paints etc.

Cutting, Chipping, Breaking RCC floor including cutting of bars and Brick Wall wherever necessary for making grooves / holes / cut out / Cable Trench etc and making good the damage after laying GI pipes cables etc with cement sand mortar make floor as required.

Demolishing brick work manually/mechanical means including stacking of serviceable material & disposal of unserviceable material outside site at unobjectionable place & as/direction of Engineer-in-charge.

Demolishing of 45 W / 60 W LED Well glass Lights from Filling Sheds as per direction of Engineer-in-charge.

Demolishing of 200 W / 300 W LED Flood Lights from High Mast & Flood Light Towers as per direction of Engineer-in-charge.

Demolishing of Flameproof LDB after disconnection of incoming and outgoing cables as per direction of Engineer-in-charge.