Department Of Housing And Urban Affairs Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 34,88,000Document Cost
₹ 20,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_DHUA_26044_1Bid Award Id
ViewTender No
CE/H and UA/17/PT-II/21-22/64, date21/06/2022Tender Authority
Department Of Housing And Urban Affairs ViewPurchaser Address
-Website
http://assamtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
2489.28
-
-
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
1574.31
-
-
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).
789.99
-
-
Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.
789.99
-
-
Cement Concrete Work.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
520.43
-
-
R.C.C Works :
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
1004.21
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
269.63
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
1116.45
-
-
FORM WORK
Centering and shuttering including strutting, propping etc. and removal of form for :
5.9.1 Foundations, footings, bases of columns, etc. for mass concrete
651.7
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform
4147.96
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.5 Lintels, beams, plinth beams, girders, bressumers and
cantilevers platform
8470.25
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts
3703.53
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :5.9.7 Stairs, (excluding landings) except spiral-staircases
280.38
-
-
Brick Work
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:4 (1 cement : 4 coarse sand)
5204.29
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
198.24
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)
6512.16
-
-
PLASTERING WORK
15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 1:4 (1 cement: 4 fine sand)
13306.16
-
-
Wood Work :
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) Sal wood
6.62
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
250.56
-
-
Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge.
309.2
-
-
35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15
mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineer-in-charge. Decorative finish (wood grained finish)
105.6
-
-
Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track an steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2
9.6
-
-
Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.9.147D.5 Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wallthickness of 2.3 ± 0.2 mm and single glazing bead / doubleglazing bead of appropriate dimension. (Area of window above 1.75 sqm)
243.11
-
-
Providing and laying Gypsum panel partitions 100 mm thick with water proof Gypsum panels of size 666x500x100 mm, made of calcite phosphor Gypsum fixed with tongue and groove, jointed with bonding plaster as per manufacturer’s specifications in superstructure above plinth level up to floor V level. Gypsum blocks will have a minimum compressive strength of 9.3 kg/cm2
368.46
-
-
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade
21.73
-
-
Floor and Floor finish (tiles)
Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).11.49.2 Size of Tile 600x600 mm
2849
-
-
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).11.47.2 Size of Tile 600x600 mm
812.4
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
1004.81
-
-
GRANITE FLOORING
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
1364.34
-
-
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
11.26.1 25 mm thick
1743.45
-
-
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.16.91.2 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.
256.78
-
-
Painting Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
12301.35
-
-
Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work
7602.72
-
-
Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10
4698.63
-
-
Providing and applying two coats of fire retardant paint on cleaned wood / ply surface @ 3.5 sqm per litre per coat including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant.
250.56
-
-
Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type)
624
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm
312
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
156
-
-
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
312
-
-
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube
12865.35
-
-
Reinforcement
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more
422632.16
-
-
Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
72735.56
-
-
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²
745.08
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
291.58
-
-
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for aminimum period of two weeks for curing and for final test.“Allabove operations to be done in order and as directed and specified by the Engineer-in-Charge : 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
739.84
-
-
Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel
Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
345.06
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. (1.5m depth)
26145.53
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.16.78.2 With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25
1694.67
-
-
Supplying and stacking at site.
16.3.2 63 mm to 45 mm size stone aggregate
2253.92
-
-
Supplying and stacking at site.
16.3.8 Red bajri
423.67
-
-
Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .
1694.68
-
-
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand
etc. all complete as per the direction of Engineer-in-charge
16946.77
-
-
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved
by Engineer-in-charge)
125.54
-
-
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.
1230
-
-
Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charge. 16.59.1 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm
25
-
-
Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.
180
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge. 2.6.1 All kinds of soil
708.93
-
-
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: 1:4 (1 cement : 4 coarse sand)
337.59
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
16.87
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
183.18
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
26.15
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)
73.15
-
-
FORM WORK
Centering and shuttering including strutting, propping etc. and removal of form for 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete
306.9
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers platform
1379.22
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts
850.95
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
1003.06
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 1:4 (1 cement: 4 fine sand)
2006.13
-
-
Painting Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete
2006.13
-
-
Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10
2006.13
-
-
Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer
72
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more
17376.04
-
-
2. Septic Tank
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil.
14.58
-
-
Supplying and filling in plinth with sand under floors, including watering,ramming, consolidating and dressing complete
5
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
0.85
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
1.89
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete
0.64
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers
0.64
-
-
Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform
7.22
-
-
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks:
1:4 (1 cement : 4 coarse sand)
8.1
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
6.08
-
-
20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
68.25
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level, Thermo-Mechanically Treated bars of grade Fe-500D or more
53.44
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
W.C. pan with ISI marked white solid plastic seat and lid
49
-
-
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
One urinal basin with 5 litre white P.V.C. automatic
flushing cistern
17
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
43
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :
Kitchen sink with drain board
510x1040 mm bowl depth 250 mm
16
-
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
49
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
59
-
-
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.
(a) 15 mm nominal dia
8
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
Flexible pipe
32 mm dia
41
-
-
40 mm dia
16
-
-
Providing and fixing 100 mm sand cast Iron grating for gully trap.
54
-
-
Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.
57
-
-
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
43
-
-
Providing and fixing toilet paper holder :
C.P. brass
49
-
-
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.
Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
41
-
-
Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
16
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
41
-
-
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
10
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms
8
-
-
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
150 mm diameter
8
-
-
Providing and Fixing 2-Way Brass Bib Tap in Polished Chrome of approved Quality and conforming to Manufacturers Standards.
49
-
-
Providing and Fixing Health Faucet with metal hose and Holder in Polished Chrome of approved quality and conforming to Manufacturers Standards.
49
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete
as per direction of Engineer in Charge.
Exposed on wall
15 mm nominal outer dia Pipes
6
-
-
20 mm nominal outer dia Pipes
16
-
-
25 mm nominal outer dia Pipes
87
-
-
32 mm nominal outer dia Pipes
66
-
-
40 mm nominal outer dia Pipes
65
-
-
50 mm nominal outer dia Pipes
155
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.
15 mm nominal outer dia Pipes
70
-
-
20 mm nominal outer dia Pipes
144
-
-
25 mm nominal outer dia Pipes
83
-
-
32 mm nominal outer dia Pipes
80
-
-
40 mm nominal outer dia Pipes
95
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
28000
-
-
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
15 mm nominal bore
25
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
15 mm nominal bore
22
-
-
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
15 mm nominal bore
59
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
15 mm nominal bore
104
-
-
Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.
25 mm nominal bore, 152mm long, weighing not less
than 440 gms
32
-
-
40 mm nominal bore, 206mm long, weighing not less
than 690 gms
19
-
-
50 mm nominal bore, 242mm long, weighing not less
than 1240 gms
6
-
-
Providing, Fixing, testing & commissoning 6 kg/ sq. cm SWR UPVC Pipe Selfit ISI marked brand as per IS 13592 complete including solvent cement jointing & hydraulic testing the joints & pipes as mentioned in the sepcification etc. and making connection with downtake wherever required to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing provided for all places, all heights & all levels.
(A) 75 mm diameter (type B)
(Horitzontal + Vertical)
169
-
-
Providing, Fixing, testing & commissoning 6 kg/ sq. cm SWR UPVC Pipe Selfit ISI marked brand as per IS 13592 complete including solvent cement jointing & hydraulic testing the joints & pipes as mentioned in the sepcification etc. and making connection with downtake wherever required to satisfaction of engr / arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing provided for all places, all heights & all levels.
(A) 100 mm diameter (type B)
(Horitzontal + Vertical)
253
-
-
Providing & fixing PVC Multi floor trap of self cleansing design haivng water seal not less than 50mm with necessary distance piece & making connection with grating, making necessary slab/ wall holes & cutting walls, grouting with M-15 CC all around with brick masonray support of 350x350 mm up to bottom of trap etc. complete as per specifications & drawing porvided at all places, all levels & all height.
(A) 110 mm inlet and 75 mm outlet (5" height)
96
-
-
Providing & fixing P- trap of self cleansing design haivng water seal not less than 50mm with necessary distance piece & making connection & support to bottom of trap etc. complete as per specifications & drawing porvided at all places, all levels & all height.
(A) 110 mm inlet and 110 mm outlet
24
-
-
Providing, Fixing, testing & commissoning 6 kg/ sq. cm PVC Pipe Selfit ISI marked brand as per IS 4985 complete including solvent cement jointing & hydraulic testing the joints & pipes as mentioned in the sepcification etc. and making connection with downtake wherever required to satisfaction of engr/ arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing provided for all places, all heights & all levels. Supreme or Equivalent.
(A)40 mm diameter
62
-
-
Providing, Fixing, testing & commissoning 6 kg/ sq. cm PVC Pipe Selfit ISI marked brand as per IS 4985 complete including solvent cement jointing & hydraulic testing the joints & pipes as mentioned in the sepcification etc. and making connection with downtake wherever required to satisfaction of engr/ arch with proper care, protecting fittings & pipes till the final handing over etc as directed by E-I-C complete as per specifications & drawing provided for all places, all heights & all levels. Supreme or Equivalent.
(B)50 mm diameter
49
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
External work
20 mm nominal outer dia Pipes
10
-
-
25 mm nominal outer dia Pipes
20
-
-
32 mm nominal outer dia Pipes
15
-
-
40 mm nominal outer dia Pipes
20
-
-
50 mm nominal outer dia Pipes
95
-
-
65 mm nominal outer dia Pipes
15
-
-
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
5
-
-
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
16
-
-
Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :
80 mm dia nominal bore
2
-
-
Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS :2373 :
80 mm dia
1
-
-
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
150 x 100 mm size P type
With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5
40
-
-
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
100 mm dia. R.C.C. pipe
40
-
-
150 mm dia. R.C.C. pipe
163
-
-
250 mm dia. R.C.C. pipe
75
-
-
300 mm dia. R.C.C. pipe
315
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg
(weight of cover 23 kg and weight of frame 15 kg) :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
26
-
-
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) :
With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5
2
-
-
Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg
40
-
-
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
1
-
-
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab
with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:
Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :
With common burnt clay F.P.S. (non modular)
bricks of class designation 7.5
4
-
-
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2
-
-
Construction of Percolation well as per below detail.
Making of 12" size bore in ground by machine at the site shown up to 200 ft with or up to water level all development and testing the same for specified percolation rate etc comp as directed & as per detail specifications.
Providing and lowering 6" Dia PVC ISI marked Heavy duty stainer pipe plain or slotted 6 kg/cm sq capacity in bore as directed & as per detail specification incl.all taxes etc comp as direction.
Gravel packing of suitable size from bottom of bore to ground level as directed as per detail specification.
Mud pit arrangement if necessary etc comp as direction.
Air compressor work making top line arrangement.
Providing, Supplying, laying and lowering and jointing ISI mark 6" Dia rigid unplasticised standard length 6 kg/cm sq PVC pipe suitable for portable water with including all taxes with jointing material etc comp as dire and detail specifications. Carting of surplus earth lime, murrum, building rubbish earth manure or sludge and exacavated rock and fly ash etc. up to 5 km lead incl. Loading & unloading the same.
2
-
-
Construction of Bore well as per below detail.
[A] Drilling & assembly lowering charges for 6"dia Borewell
[B] Mudpit Digging Charges
[C] Electro-logging Charges
[D] Gravel Packing Charges (Nos. 1 Truck)
[F] Air Compressor Charges
[G] Chemical Water Testing (ATIRA Lab)
[H] Removal of Mud from Mudpit Tanker Approx.
[I] 6"dia PVC Casing Pipe "ISI" CM Heavy
[J] 6"dia PVC Strainer Pipe "ISI" CM Heavy
[K] 6"dia Heavy Top Cap, Bail Plug & Clamp with Nut Bolt
[L] Gravel Supply ( Special Grade) (No.1 Truck)
[O] 4 sqmm flat cable Jaison make
[P] 2"dia Upvc heavy column pipe
[Q] 2" dia Top bottom piece, G I bend, coupling, Sand guard, MS clamp with nut bolt etc.,
[R] Pump Installation charges
1
-
-
Supplying including installation, testing and commissioning of Supply of 30 Kva Greaves Make Factory Built Supper Brand DG Set incorporating GREAVES Engine and Meccalte/ Equivalent alternator with AMF Panel with all STD Accessories like, AMF Logic Battery & SMPS Battery Charger, AVM Pads, Acoustic Enclosure, etc.
1
-
-
11 KV line with 11/0.4 KV 500KVA DTR sub station for providing power supply at proposed ISBT site, near by pass, chaboti, N Lakhimpur under N Lakhimpur Electrical sub-division, APDCL
1
-
-
3. Wiring
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Group C
614
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
71
-
-
Wiring for light/ power plug with 2 x 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
100
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire
1345
-
-
2 x 2.5 sq. mm + 1 x 1.5 sq. mm earth wire
1290
-
-
2 x 4.0 sq. mm + 1 x 2.5 sq. mm earth wire
1400
-
-
2 x 6.0 sq. mm + 1 x 4.0 sq. mm earth wire
43
-
-
2 X 10 sq. mm + 1 X 6 sq. mm earth wire
50
-
-
2 X 16 sq. mm + 1 X 6 sq. mm earth wire
50
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
50
-
-
4 X 16 sq. mm + 2 X 6 sq. mm earth wire
50
-
-
Supplying and drawing co-axial TV Cable RG 6 Grade, 0.7 mm solild copper conducter PE Insulated, shielded with find tinned cocpper braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.
180
-
-
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
20 mm
10
-
-
25 mm
10
-
-
50 mm
10
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
20 mm
530
-
-
25 mm
3175
-
-
32 mm
50
-
-
40 mm
50
-
-
50 mm
50
-
-
Supplying and fixing following moduler switch /socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required.
6 pin 15/16 A socket outlet
90
-
-
3 pin 5/6 A socket outlet
130
-
-
15/16 A switch
90
-
-
5/6 A switch
130
-
-
Bell push
15
-
-
TV antenna socket outlet
16
-
-
Supplying and fixing Two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.
193
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
65
-
-
Supplying and fixing following size/modules, GI box alongwith modular base and cover plate for modular switches in recess etc. as required.
1 or 2 Module (75mmX75mm)
22
-
-
3 Module (100mmX75mm)
5
-
-
4 Module
5
-
-
6 Module (200mmX75mm)
5
-
-
8 Module (125mmX125mm)
5
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.
259
-
-
Supplying and fixing suitable size GI box with modular plate and cover in FRLSont on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
209
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
122
-
-
Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.
72
-
-
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
118
-
-
Wiring for group controlled (looped) light point/fanpoint/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
Group C
298
-
-
Supplying and fixing 20 A, 240 V, SPN Industrial type socketoutlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
2
-
-
4. MCCB, MCB & DB's
-
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
8 way , Double door
19
-
-
12 way , Double door
1
-
-
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
4 way (4 + 12), Double door
3
-
-
8 way (4 + 24), Double door
2
-
-
Supplying and fixing of following ways surface/recess mounting, vertical type, 415V, TPN MCB distribution board of sheet steel, dust protectred, duly powder paintned, inclusive of 200A tinned copper busbar, common neutral link, earth bar, din bar for mouting MCBs (but without MCBs and incomer) as required.
4 way (4 + 12), Double door
3
-
-
8 way (4 + 24), Double door
3
-
-
12 way (4 + 36), Double door
3
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
220
-
-
Double Pole
18
-
-
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
29
-
-
Supplying and fixing folowwing rating, double pole, 240 V, isolator in the exisitng MCB DB completer with connections, testing and commissioning etc. as required.
40A
1
-
-
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
40A FP MCB
4
-
-
63A FP MCB
16
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
25 A
2
-
-
40 A
7
-
-
63 A
2
-
-
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
25 A (30 mA)
2
-
-
40 A (30 mA)
12
-
-
63 A (30 mA)
48
-
-
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
5
-
-
Supplying with fitting and fixing 30/100/300 mA sensitivity 240/415v 50 Hz DP RCCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.
25 A (30 mA)
18
-
-
5. MEDIUM VOLTAGE CABLES
-
-
-
Supply, Laying, Connection,Testing and Commissioning of heavy duty medium voltage cables as per Specification and IS 7098 part II, XLPE insulated, inner & outer sheathed, Screened stranded Al / Cu conductor unless or otherwise specified.The cable shall be laid as per the specification.
The unit rate shall include (1) Shifting of cable from site store to place of installation.
(2) Supply & fixing of cable G I clamps(With GI Screw) ,Nylon Tie, brackets, supports, route markers etc. where ever required to fix the cables safely.
(3) Earthing the glands and armouring with earthing clamp and jumper and also connecting to common earth bar.
(4) Testing of insulation and continuity of cable and submission of reports to the client's representative.
3.5C x 150 mm2 Al XLPE Armoured Cable
50
-
-
3.5C x 70 mm2 Al XLPE Armoured Cable
20
-
-
3.5C x 50 mm2 Al XLPE Armoured Cable
20
-
-
3.5C x 35 mm2 Al XLPE Armoured Cable
60
-
-
4C x 25 mm2 Al XLPE Armoured Cable
60
-
-
4C x 16 mm2 Al XLPE Armoured Cable
620
-
-
4C x 10 mm2 Al XLPE Armoured Cable
10
-
-
4C x 6 mm2 Al XLPE Armoured Cable
10
-
-
4C x 4 mm2 Al XLPE Armoured Cable
10
-
-
3C x 10 mm2 Al XLPE Armoured Cable
10
-
-
6. CABLE KITS
-
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3.5C x 150 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 70 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 50 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 35 mm2 Al XLPE Armoured Cable
2
-
-
4C x 25 mm2 Al XLPE Armoured Cable
2
-
-
4C x 16 mm2 Al XLPE Armoured Cable
18
-
-
4C x 10 mm2 Al XLPE Armoured Cable
2
-
-
4C x 6 mm2 Al XLPE Armoured Cable
2
-
-
4C x 4 mm2 Al XLPE Armoured Cable
2
-
-
3C x 10 mm2 Al XLPE Armoured Cable
2
-
-
7. ELV SYSTEM
-
-
-
SITC Advance Hybrid IP Key Telephone System
• 04 PRI • 08 Digital Ext.
• 100 Analog Ext(CLI)
• 10 IP Extensions
• Expandable up to 200 port 02 Channel Simplify Voice Mail / Auto Attendant
PC Telephony CA Assistance (All User) 01 Built-In LAN Port
Conference :-
• 3*10 party Conference
• 8*4 Party Conference
• 32 Party meet me conference
1
-
-
SITC Panasonic IP-Phones
10
-
-
SITC Remote Maintenance for programming and software updating
2
-
-
SITC MDF Required for IPABX 100 Pair
5
-
-
SITC of Telephone Instruments.
80
-
-
SITC of Digital Telephones: 60 DSS
2
-
-
SITC of Analog Telephone CLI
80
-
-
8. CEILING FAN, EXHAUST FAN AND AIR CURTAIN
-
-
-
Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].
1200 mm Sweep
15
-
-
Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.
Ventil Air DB 300 mm sweep
10
-
-
9. AIR CONDITIONER
-
-
-
Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection as approved by the Deptt.)up to 10 between the room unit and out door unit as directed by the department with fixing accessories
2 Ton capacity
(Carrier make)
3
-
-
1.5 Ton capacity
(Carrier make)
45
-
-
1 Ton capacity
(Carrier make)
2
-
-
10. FABRICATION
-
-
-
SITC of fabrication work from MS structure for other work with anchor fastner and necessary hardware with necessary welding has to be done to complete the job from ISA/ISMC/ PLATE.The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant.
1100
-
-
SITC of fabrication work from MS structure for other work with anchor fastner and necessary hardware with necessary welding has to be done to complete the job from ISA/ISMC/ PLATE.The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant.
50
-
-
11. LIGHTING FIXTURES
-
-
-
Supply, Installation, Assembling, Connection, Testing & Commissioning Energy Saving Recess / Surface Mounted LED Down Light Luminaire with all other necessary accessories to complete the installation satisfactorily. The Lighting Fixtures should have Design amient temperature 45 Deg C. The Luminaire shall have a CRCA Powder coated body and a high efficiency diffuser with electronic driver shall operate a power factor 0.9 and THD 10%.
Supply, Installation, Assembling, Connection, Testing & Commissioning of Supply, of LED high bay luminaire of 105W having System Efficacy 145 lm/W, system output 15000 Lumens, THD 10%, Power Factor 0.95, CRI 70, CCT 5700K, Full IP 65 protected single piece die cast aluminium housing having integrated PC lens cover having integrated optics with Impact resistance IK08, Life L70B50 @ 50k hrs. BIS compliant driver, EMC -EMI compliant. Driver shall have 4KV Surge protection. Luminaire should have option of wide and narrow beam angle options with Operating temperature range from 0 to 55 deg C. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make. Similar to Philips BY515P LED150S 5700 WB PSU GR
43
-
-
Supply, Installation, Assembling, Connection, Testing & Commissioning of LED batten light having system wattage of maximum 18W with System Efficacy 120 lm/W, delivering minimum 2000 lumens, THD 10%, Power Factor 0.95, CRI 80, CCT 6500, IP20 CRCA housing , Life L70B50 @ 50k hrs, Ripple 5%, Inbuilt PIR (Movement Sensor) which Dim the Luminaire to 50% in case of no movement. BIS compliant driver High low cut with auto restart feature @ 140-270V, EMC -EMI compliant. Driver shall have 4KV Surge protection. Driver should have Class B servicability (mainatainable at site). LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make. Similar to Philips BN170C LED20S 6500 PSU L120 Or Equi
193
-
-
Supply Installation Testing and Commissioning of Recessed Mounted 2X2 LED Luminaire with system lumen output of 3100 lumens and minmum system efficacy of 120lm/W. Power consumption of luminaire shpuld be 25W with color temperature of 5700K and CRI80, . The luminaire shall meet IP20 rating with Ripple 5%, THD10% and PF 0.95. The luminaire housing should made of powder coated CRCA with high efficiency PS diffuser and having surge protection up to 4kV. The driver must have operating voltage range from 120-270VAC and EMI/EMC compliant. Luminaire should have Class B serviceability. Luminaire should accommodate different color tiles & also accommodate Services like-AC Grill & Smoke detector etc. LM79 and LM80 reports must be submitted from a NABL accredited laboratory, Luminaire and Driver must have BIS certificate and same must be submitted for records.Driver and luminaire shall be of same make. Similar to Philips RC380B LED30S-6500 G6 L60W60 PSU OD
185
-
-
Supply Installation Testing and Commissioning of maximum 11W recessed mounted High quality polycarbonate diffuser and PDC Al housing recessed design 150 mm Cutout for visual comfort Downlighter delivering 1200 Lumen, 4000K CRI80, THD 10%,, Input voltage Range 140-270 VAC , EMI EMC Complient (as per CISPR 15)Replacable driver Luminaire driver both BIS Complient and having CRS ( R No ) L70B50 @ 50K Hrs, Power factor0.95, IP20 protection, operating temperature range from 0 to 45 deg C, internal surge protection of 2.5kV. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make. Similar to Philips DN296B LED12S-6500 PSU WH
65
-
-
Supply Installation Testing and Commissioning of maximum 13.5W recessed mounted High quality polycarbonate diffuser and PDC Al housing recessed design 150 mm Cutout for visual comfort Downlighter delivering 1500 Lumen, 4000K CRI80, THD 10%,, Input voltage Range 140-270 VAC , EMI EMC Complient (as per CISPR 15)Replacable driver Luminaire driver both BIS Complient and having CRS ( R No ) L70B50 @ 50K Hrs, Power factor0.95, IP20 protection, operating temperature range from 0 to 45 deg C, internal surge protection of 2.5kV. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make. Similar to Philips DN296B LED15S-6500 PSU WH
85
-
-
12. CCTV SYSTEM
-
-
-
Supply, Installation, Testing & Commissioning of 2MP IR Bullet Varifocal Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps,2.7 to 13.5 mm Varifocal Motorized lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Audio: 1 Ch Input & Output, Alarm: 1 Ch Input & Output, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Scene change detection,Motion detection, Face detection, Video tampering, UL, CE certified.
45
-
-
Supply, Installation, Testing & Commissioning of 2MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified.
50
-
-
Supply, Installation, Testing & Commissioning of 2MP IP ANPR Camera: 1/1.8′′Progressive Scan CMOS, 1920 × 1080 at 60fps,5.3 to 13 mm lens, ICR, ONVIF, support H.265, H.264,MJPEG, 3D Digital Noise Reduction, 24 V DC ± 20%, Support IR-30m,Support on-board storage up to 128 GB (TF card not included),License Vehicle detection with inbuilt independant automatic License plate recognition system working on optical character recognition technology. Camera should provide clear image of license plate along with recognized license plate no. and capture time, UL, CE, FCC certified.
6
-
-
Supply, Installation, Testing & Commissioning of 2MP IR Indoor Dome Fixed Camera -1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8mm Fixed lens, 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.
84
-
-
Supply, Installation, Testing & Commissioning of IP Fixed Mini Dome Camera: 1/2.7" Progressive Scan CMOS, ICR, 0.01 lux at F1.2, 0 lux with IR, 1920x1080:25fps, 2.8mm Fixed Lens, H.265, MJPEG, Three individually configurable stream, IK08, IP66, DC12V & PoE, 120dB WDR, 3D DNR, BLC, Support on-board storage up to 128GB (SD card not included), Alarm -1 input,1 output, IR range: up to 10m, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection,face detection, video tampering, UL, CE, FCC certified.
1
-
-
Supply, Installation, Testing & Commissioning of 2MP IR Outdoor PTZ Camera-1/2.8" Progressive Scan CMOS, 1920 × 1080 at 60fps, 4.8 mm to 153 mm, 32× Optical, 16x digital zoom, Color: 0.005 Lux at F1.6, B/W: 0.001 Lux at F1.6, ICR, ONVIF, support H.265,MJPEG, 120 dB WDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, Tripple individually configurable stream, 24 VAC & Hi PoE, IR range: 150m, Pan: 360° endless, Tilt: From -15° to 90° (auto-flip), Pan Speed - from 0.1°/s to 160°/s, Preset Speed: 240°/s, Tilt Speed- from 0.1°/s to 120°/s, Preset Speed: 200°/s, Presets- 300, Alarm Input-2-ch alarm input, Alarm Output-1-ch alarm output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), IP66, IK10, Face Detection, Intrusion Detection, Line Crossing Detection, Region Entrance Detection, Region Exiting Detection, UL, CE, FCC certified.
14
-
-
Supply, Installation, Testing & Commissioning of 128ch Network Video Recorder- Connect Up to 128 IP Cameras, dual-OS design, Up to 12 Megapixels Resolution, 2 HDMI output with one atleast at 4K (4096×2160) , 1 VGA output with 2MP resolution,Support H.265/MJPEG, Incoming Bandwidth 500 Mbps, 16 SATA Hard Disks, ANR Technology, 16 SATA interfaces for 16 HDDs and capacity of each HDD upto 8 TB, front panel: 1 × USB 2.0 rear panel: 2 × USB 3.0, Alarm I/O 16/8, RS-485, 4 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified.
2
-
-
Supply, Installation, Testing & Commissioning of 6TB Surveillance Hard Disk
34
-
-
Supply, Installation, Testing & Commissioning of Surveillance class Common Micro SD Card 128GB for camera
200
-
-
Supply, Installation, Testing & Commissioning of Video Management Software along with Work Station
1
-
-
Supply, Installation, Testing & Commissioning of Joystick
4
-
-
Supply, Installation, Testing & Commissioning of 55" LED Display Monitor , mouse, keypad as required as per specification.
4
-
-
Supply, Installation, Testing & Commissioning of Intel® Core i7 Latest Generation 16GB System RAM
2GB Graphics card
monitors – 24” Full HD
128GB SSD + 1TB 7200 rpm HDD
Keyboard, 3 button Mouse and Video Monitoring Joystick 24x7 working capacity
4
-
-
13. PA SYSTEM
-
-
-
SITC of 6W Ceiling Speaker with max SPL1M/1W 96dB . Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W
50
-
-
SITC of 6W Wall mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W
100
-
-
SITC of 20W Column Speaker 107dB . Frequency response of 300Hz-15KHz. The speaker shoud have tappings at 20W/10W/5W/2.5W
50
-
-
SITC of 8 zone IP based, digital Voice Alarm controller expandable upto 128 zones. The voice alarm controller should be able to connect directly over Ethernet. It should have functions like the audio playing, zone control, fault monitoring, log recording, volume control and amplifier switchover. The Voice alarm controller should also have the following functions:
. 255 Priorities
. Time schedule broadcasts
. Its own PTT microphone
. Capable of amplifier redundancy
. 8 trigger inputs/outputs
3
-
-
SITC of IP based Networkable touch screen paging station for selection of zones, supervision of system status, setting of scheduled broadcasts with the following functions:
. Built-in monitoring loudspeaker
. Detachable goose-neck microphone
. LCD touchscreen display
. Audio input
1
-
-
SITC of 1X500W Class-D Amplifier with 1 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection
5
-
-
Supply and Laying of 2 x 2.5 sq mm speaker cable in existing conduit
1500
-
-
Supply and Laying of 2c x 1.5 Sq.mm Sheilded Armoured cable
1500
-
-
14. DATA NETWORK
-
-
-
Supply, Installation, Testing & Commissioning of Layer 3 Switch with minimum of 03Port 1G Fiber + 24 Port Giga Copper switch, supporting Multimode SFP/ SX modules. Should have Non-blocking switch fabric, IPv6 Ready, with RPS. The core switches, should be implemented in Active - Active, redundant topology for High Availability.
1
-
-
Supply, Installation, Testing & Commissioning of Layer II Managed Ethnernet switch : 24 port RJ45 10 base 1000 T (POE) with 4 nos uplink fiber combo ports
10
-
-
Supply, Installation, Testing & Commissioning of Layer II Managed Ethnernet switch : 24 port RJ45 10 base 1000 T with 4 nos uplink fiber combo ports
6
-
-
Supply, Installation, Testing & Commissioning of Single-Mode SFP /SX transceivers supporting 10G
6
-
-
Supply, Installation, Testing & Commissioning of Single-Mode SFP /SX transceivers supporting 1G
10
-
-
Supply, Installation, Testing & Commissioning of Network Management software
1
-
-
Suppling and drawing 4 pair shielded, 0.5 mm PVC.Insulated copper conductor un-armoured Cat-6 computer cable FR with existing surface / concealed ,steel / PVC. Conduit/Casing-Ncapping as required.
3000
-
-
Supply, Installation, Testing & Commissioning of RJ - 45 Computer Jack cat 6 with shutter Modular (1Module)
200
-
-
Supply, Installation, Testing & Commissioning of RJ - 45 Computer Jack cat 6 with shutter Modular (2Module)
100
-
-
Supply, Installation, Testing & Commissioning of 19" Modular Patch - 1 U Patch Panel 24, RJ 45 Cat-6 connector
20
-
-
Supply, Installation, Testing & Commissioning of 19" Modular telephone Patch Panel 24 - 1 U with RJ 11 connector
5
-
-
Supply, Installation, Testing & Commissioning of CAT 6 RJ45 Patch Cord F/UTP 1 Mtr
600
-
-
Supply, Installation, Testing & Commissioning of CAT 6 RJ45 Patch Cord F/UTP 2 Mtr.
600
-
-
Supply, Installation, Testing & Commissioning of CAT 6 RJ45 Patch Cord F/UTP 3 Mtr.
25
-
-
Supply, Installation, Testing & Commissioning of CAT 6 RJ45 Patch Cord F/UTP 5 Mtr.
25
-
-
Supply, Installation, Testing & Commissioning of 800 mm x 1000 mm 42 U 230 V AC 90 CFM fan 2 , 5 Hardware packet 1 set ( containing 20 Nos Nos of 3), stationary shelf , Two Cable manager 1U height. Varitical cable manager .
2
-
-
Supply, Installation, Testing & Commissioning of 12U cabinet 638X600X500, wall mounting with power supply and Fan etc.
10
-
-
Supply, Installation, Testing & Commissioning of 1U Horizontal Cable Manager (For Field Cables & Switches)
15
-
-
Supply, Installation, Testing & Commissioning of CAT6 Socket Universal Power Strip with MCB
25
-
-
Supply, Installation, Testing & Commissioning of 4-pair Patch Cords (70 labels per sheet)
600
-
-
Supply, Installation, Testing & Commissioning of 25 pair riser cable
2500
-
-
Supply, Installation, Testing & Commissioning of 50 pair 0.61 mm dia tinned copper armoured cable
1500
-
-
Supply, Installation, Testing & Commissioning of 6 Core Laser Speed 150 outdoor SM Fibre Optic Cable in ground/clamped to existing cable tray, complete as required
160
-
-
Supply, Installation, Testing & Commissioning of Rack Mount24 port Shelf LIU's, SC Coupler Adapter Plates, SM LC Couplers, SM SC Pigtails and additional equipment as required for Fibre Optic terminations of the complete system including the costs of necessary Retainers, Mounting arrangements, screws and identification labels etc complete as per specifications and as required.
2
-
-
Supply, Installation, Testing & Commissioning of 6 core SM fiber patch patch 3 mtr
20
-
-
Supply, Installation, Testing & Commissioning of Rack Mount 12 port Shelf LIU's, SC Coupler Adapter Plates, SM LC Couplers, SM SC Pigtails and additional equipment as required for Fibre Optic terminations of the complete system including the costs of necessary Retainers, Mounting arrangements, screws and identification labels etc complete as per specifications and as required.
8
-
-
Suppling and drawing 4 pair shielded, 0.5 mm PVC.Insulated copper conductor un-armoured Cat-6 computer cable FR with existing surface / concealed ,steel / PVC. Conduit/Casing-Ncapping as required.
5000
-
-
15. WIFI SYSTEM
-
-
-
Supply, Installation, Testing & Commissioning of Ruckus R510c, omni, indoor Access point, 802.11ac Wave 2 2x2:2 internal BeamFlex+, dual band concurrent. One ethernet port, PoE input. Includes mounting bracket and one year warranty. Does not include PoE injector.
25
-
-
Supply, Installation, Testing & Commissioning of Ruckus T310c, omni, outdoor Access point, 802.11ac Wave 2 2x2:2 internal BeamFlex+, dual band concurrent. One ethernet port, PoE input. Includes mounting bracket and one year warranty. Does not include PoE injector.
15
-
-
Supply, Installation, Testing & Commissioning of Spares of Power over Ethernet (PoE) Adapter (10/100/1000 Mbps) with IN power adapter, quantity of 1 unit (applicable for 7731, P300, R710, R610, R700, R600, R500, R510, R300, R310, 7982, 7372, 7352, 7321, H510, H500, H320, 7055, T300, T301, T610, T610s, M510)
40
-
-
Supply, Installation, Testing & Commissioning of ZoneDirector 1200, licensed for up to 5 Ruckus Access Points. ZD1200 can be upgraded to support up to 75 APs with AP license upgrades if using software release pre ZD10.0. If using software ZD10.0 and above, ZD1200 can be upgraded to support up to 150 APs with license upgrades.
1
-
-
Supply, Installation, Testing & Commissioning of ZoneDirector 1200 Single AP License Upgrade SKU. Max orderable upgrade license quantity is 70 if using software pre ZD10.0. If using release ZD10.0 and above, max orderable upgrade license quantity is 145.
35
-
-
16. MEDIUM VOLTAGE PANELS
-
-
-
Supplying and installation of metal enclosed free standing floor readable mounted front operated cubical type switch gear panel suitable for OUTDOOR Type installation conforming to IS: 8623 (Part I & II). Panel should be made of sheet steel and thickness not less than 2mm and structural steel having light section with arrangement for sealingthe covers and lockable doors. The panel shall be completely dust tight and vermin proof and shall be painted with anti corrosive and anti condensation type two coats of primer and two coats of paint conforming to Degree of Protection for enclosure shall be IP-55. All wiring shall be PVC insulated and PVC sheathed of 1100 volt grade of required size. The panel should have provision of entry of cable at the bottom and also provision of out going feeders from the bottom of the panel. The panel shall be incorporated with single copper busbar system. The bus bar shall be of high quality copper of uniform cross section. The panel shall consist of the following items (viz. Voltmeter, Ammeter, CT, indicating lamps, selector switch etc.) connected as per drawing and shall be flush mounted on the front of the panel.
Supply, Installation, Testing and Commissioning of MAIN LT PANEL As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation, Testing and Commissioning of APFCR PANEL As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation, Testing and Commissioning of SUB LT PANEL 1 As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade
5
-
-
Supply, Fitting Fixing of Shock Treatment Chart
1
-
-
17. WIRING
-
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (For Pole Junction Box to Pole Light)
100
-
-
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red
colour on front side as required.
2
-
-
18. MEDIUM/HIGH VOLTAGE CABLES
-
-
-
Supply, Laying, Connection,Testing and Commissioning of heavy duty medium voltage cables as per Specification and IS 7098 part II, XLPE insulated, inner & outer sheathed, Screened stranded Al / Cu conductor unless or otherwise specified.The cable shall be laid as per the specification.
The unit rate shall include (1) Shifting of cable from site store to place of installation.
(2) Supply & fixing of cable G I clamps(With GI Screw) ,Nylon Tie, brackets, supports, route markers etc. where ever required to fix the cables safely.
(3) Earthing the glands and armouring with earthing clamp and jumper and also connecting to common earth bar.
(4) Testing of insulation and continuity of cable and submission of reports to the client's representative.
3.5C x 95 mm2 Al HTXLPE Armoured Cable
15
-
-
3.5C x 150 mm2 Al LTXLPE Armoured Cable
330
-
-
3.5C x 70 mm2 Al LTXLPE Armoured Cable
10
-
-
3.5C x 50 mm2 Al LTXLPE Armoured Cable
10
-
-
3.5C x 35 mm2 Al LTXLPE Armoured Cable
10
-
-
4C x 25 mm2 Al LTXLPE Armoured Cable
10
-
-
4C x 16 mm2 Al LTXLPE Armoured Cable
1350
-
-
4C x 10 mm2 Al LTXLPE Armoured Cable
10
-
-
4C x 6 mm2 Al LTXLPE Armoured Cable
10
-
-
4C x 4 mm2 Al LTXLPE Armoured Cable
10
-
-
3C x 10 mm2 Al LTXLPE Armoured Cable
1350
-
-
19. CABLE KITS
-
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3.5C x 95 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 150 mm2 Al XLPE Armoured Cable
18
-
-
3.5C x 70 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 50 mm2 Al XLPE Armoured Cable
2
-
-
3.5C x 35 mm2 Al XLPE Armoured Cable
2
-
-
4C x 25 mm2 Al XLPE Armoured Cable
2
-
-
4C x 16 mm2 Al XLPE Armoured Cable
66
-
-
4C x 10 mm2 Al XLPE Armoured Cable
2
-
-
4C x 6 mm2 Al XLPE Armoured Cable
2
-
-
4C x 4 mm2 Al XLPE Armoured Cable
2
-
-
3C x 10 mm2 Al XLPE Armoured Cable
30
-
-
20. EARTHING
-
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm diaincluding accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
12
-
-
Extra for using salt (5k and charcoal 64k in pipe earthing station pit to provide low impedance ground in locationi of high soil resistivity as and when required and specified by the dept.
12
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
4
-
-
Extra for using salt (5k and charcoal 64k in pipe earthing station pit to provide low impedancec ground in locationi of high soil resistivity as and when required and specified by the dept.
4
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.
4
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
750
-
-
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
100
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.
(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
100
-
-
21. FABRICATION
-
-
-
SITC of fabrication work from MS structure for other work with anchor fastner and necessary hardware with necessary welding has to be done to complete the job from ISA/ISMC/ PLATE.The job also includes to paint the structure with two coats of red oxide and two coats color of enamel paint as approved and recommended by consultant.
500
-
-
22. MV CABLE LAYING
-
-
-
Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
300
-
-
23. MISC. CIVIL ITEMS
-
-
-
Excavation for cable trenches of depth upto 1.2 m in soft soil including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.
1500
-
-
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.
100 mm dia
300
-
-
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.
63 mm dia (OD-63 mm & ID-51 mm nominal)
100
-
-
24. LIGHTING FIXTURES
-
-
-
Supply, Installation, Assembling, Connection, Testing & Commissioning Energy Saving Recess / Surface Mounted LED Down Light Luminaire with all other necessary accessories to complete the installation satisfactorily. The Lighting Fixtures should have Design amient temperature 45 Deg C. The Luminaire shall have a CRCA Powder coated body and a high efficiency diffuser with electronic driver shall operate a power factor 0.9 and THD 10%.
Supplying, installation, testing and Commission of Supply of Integral Asymetrical Wide Beam LED Flood Light Luminaire With min System Lumen output of 48500 lumens. Luminaire should be with specially designed heat management system to ensure luminous efficacy 125 Lm/w for the system and Power consumption of the luminaire should be maximum 300W.The housing should be of non-corrosive high-pressure die-cast aluminum to with stand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Luminaire should be IP66 and IK08 protection and should meet safety and performance and EMI standards. LEDs Make should be from Lumiled / NICHIA / Osram only with High power Single white LED chip with ceramic base. which is having CCT of 5700 K, CRI 70, SDCM 5 with useful life of L70@50000 Hrs Operating Voltage of driver should be of 120 – 270 VAC.The access to the optical and the gear compartment should be separate. While accessing the gear compartment, the optical compartment should not be disturbed. The Luminaire should have a 20 KV /10 KA SPD duly bolted in the Luminaire . The SPD should be able to sustain a minimum 15 hits of 10KA rating i.e. Total of 45 hits across all the three modes as per IEEE 62.41.2. The Luminaire should have a breather to ensure that air balance inside and outside of the Compartment .The luminaire should be of Class B Serviceability. The wattage of each LED should be greater than 1 watt and less than 3 Watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. Multi Chip , array multi die , mid power ,Integrated arrays and COB’s are not permitted. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire. Submission of LM80-08 for LED source & LM79-08 for Luminaire from third NABL Accredited Lab mandatory. The Luminaire and Driver both should be BIS approved and CRS no (R no) of both driver and Luminaire along with BIS certificates should be submitted at the time of bid submission. Similar to Philips PHILIPS BVP485 LED485 CW AWB PSU SPD GR.
42
-
-
Supplying, installation, testing and Commission of LED street light fitting with system lumen output of 8350 lumens and minimum system efficacy 120lm/W. System Power Consumption should be 70W. Luminaire should be made of Pressure Die Cast Housing LM 6 Alloy with IP66 and IK07 protection, THD≤10% and should have provision of 4KV Internal , Street Light can take 440V stress upto 8 Hrs , Auto Restart Feature . Similar to BRP062
30
-
-
MAIN LT PANEL : Supply, Installation, Testing and Commissioning of EXTERNAL LIGHTING DB As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade
2
-
-
25. LIGHTING POLE
-
-
-
Supply Installation Testing and Commissining of 9 mtr high hot dip galvanised Octagonal poles with 155mm bottom dia & 70 mm top dia made up of 3mm thk. HT sheet alongwith base plate of size 250X250X16mm thk. ( without Bracket) with inbuilt junction box
Supply of 4Nos of M20X600mm long 'J' type EN 8 grade foundation bolts along with template
Supply of 1mtr long hot dip galvanised Single arm bracket made up of 42mm dia GI pipe suitable to mount on 70mm dia pole
30
-
-
Supply Installation Testing and Commissining of 20 M high mast shaft in Two section suitable for 50 m/sec wind speed as per IS:875 part III along with head frame, luminaires carriage suitable for 14 nos LED Flood light luminaires in Symmetrical arrangement and other accessories manufactured in factory.
Make - RR ISPAT , Data- 20 Mt High Mast , Top-150 mm ,Bottom-410 mm , Section Thickness - 3/4 mm , PCD-490 MM (8 Hole)
Supply of raising lowering system comprising double drum winch, 5mm diameter SS wire rope, trailing cable, connector, integral power tool motor, manual handle, junction box, lightning finial. (Wiring material from JB to individual luminaire, FP to HM & MCB in base compartment are not included and are a part of installation).
Item - SS 316 6mm Wire rope, EPR CU Trailing Cable 5C x 2.5Sqmm - 1 Ckt, Winch- SGDD 750Kg, Motor 3Ph 1.0HP
Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template.
Size- M30 x 8 nos, 850 MM long, Anchore Plate PCD- 490 mm (8 Hole) , One Common template will provide -Size 490mm (8 Hole)
Supply of LED type Single dome aviation obstruction light.
Supply of outdoor stand mounted feeder pillar with 32A TPN MCB incomer, Single dial time switch, 25A TP contactor for the automatic switching of luminaries, power tool control with 2 no 9A contactors and raise lower push button, Incoming 35 sq. mm and out going 16 & 2.5 sq. mm terminals.
4
-
-
Supplying and installation of metal enclosed free standing floor readable mounted front operated cubical type switch gear panel suitable for OUTDOOR Type installation conforming to IS: 8623 (Part I & II). Panel should be made of sheet steel and thickness not less than 2mm and structural steel having light section with arrangement for sealingthe covers and lockable doors. The panel shall be completely dust tight and vermin proof and shall be painted with anti corrosive and anti condensation type two coats of primer and two coats of paint conforming to Degree of Protection for enclosure shall be IP-55. All wiring shall be PVC insulated and PVC sheathed of 1100 volt grade of required size. The panel should have provision of entry of cable at the bottom and also provision of out going feeders from the bottom of the panel. The panel shall be incorporated with single copper busbar system. The bus bar shall be of high quality copper of uniform cross section. The panel shall consist of the following items (viz. Voltmeter, Ammeter, CT, indicating lamps, selector switch etc.) connected as per drawing and shall be flush mounted on the front of the panel.
Supply, Installation, Testing and Commissioning of EXTERNAL LIGHTING PANEL As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation, Testing and Commissioning of MAINTANANCEC SHED PANEL As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation, Testing and Commissioning of STAFF QUARTERS PANEL As per Single Line Diagram Dwg No. AMC-E-SLD-01
1
-
-
Supply, Installation antistatic rubber mat suitable for 1.1 KV Voltage grade
5
-
-
Supply, Fitting Fixing of Shock Treatment Chart
1
-
-
I) FIRE PUMPS & ACCESSORIES, YARD HYDRANT, INTERNAL HYDRANT, HOSE REEL & SPRINKLER SYSTEM
Supply, Installation, Testing and Commissioning of Electric driven Fire pump (Hydrant) suitable for automatic operation and consisting of following: complete in all respect as required.
a) Horizontal, centrifugal, back pullout pump to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet at specified flow of 2280 lpm at 75 m. head conforming to IS standards.
b) Squirrel cage induction motor with suitable HP with synchronous speed 3000 RPM, Suitable for operation on 415 volts, 3 phase 50 Hz. AC with IP 55 protection for enclosure, horizontal foot mounted type with Class-F insulation, Conforming to IS standards. c) Common Base plat for Pump and motor and coupling, coupling guard and other accessories as required for complete installation of pump set.
d) Suitable cement concrete foundation with cement concrete plaster complete with anti-vibration arrangement
1
-
-
Supplying, Installation, Testing and Commissioning of Control Panel suitable for automatic operation of fire fighting pumps consisting.
(a) Necessary cabling, wiring, earthing from panel to individual equipment shall be included in the quoted price.
(b) Facility for more selections i.e auto or manual.
(c) Protection failure and control cabling.
(d) interlocking of pressure switch with pumps
1
-
-
Supply, Installation, Testing and Commissioning of the following sizes of flange jointed / screwed / welded, M.S. Pipes of Class C (Heavy class) ISI marked including accessories such as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions / bends / flanges etc., and laying on the surface including painting with two coats of anticorrosive primer and two coats of approved red enamel paint after laying and testing after Installation etc. as per specifications complete as required.
a) 150 mm dia.
235
-
-
b) 100 mm dia.
120
-
-
Supply, installation, testing and commissioning of C.I. Butterfly valve (PN 1.6) with flanges, nut bolts, gaskets complete as required.
a) 150 mm dia.
2
-
-
b) 100 mm dia.
2
-
-
Supply, Installation, Testing and Commissioning of Cast iron Dual plate Check valve (PN 1.6)
a) 150 mm Dia.
2
-
-
Supply, installation, testing and commissioning S.S. Single Headed Fire Hydrant Valve with 80 mm N.B. flanged inlet, 63 mm dia female instantaneous outlet type. S.S. coupling, blank cap, chain, twist release type lug & all accessories Conforming to IS:5290. Including fixing with supports, flanged tapping from wet riser, orifice plate complete as required by the Local Fire Authority. (Location : External/Internal Fire Hydrant)
5
-
-
Supply, Installation, Testing and Commissioning of Weather proof Standard Fire Hose Cabinet wall mounting type (750 mm x 600 mm x 250 mm deep) having single or double opening with necessary locking arrangement by allan key suitable for housing 2 nos. hose pipe, 1no. Branch pipe & nozzle spanner. (Location : External/Internal Fire Hydrant)
4
-
-
Supply, installation, testing and commissioning non-percolating rubber reinforced lined fire Hose pipe (as per IS : 636) of 63 mm dia and 2x15 mtrs long. The hose shall be rated for burst pressure of 35.7 Kg/sqcm. Hose shall be complete with ISI marked SS male & female coupling (IS:903) bound & riveted to hose pipe with copper rivets & 1.5 mm copper wire.
4
-
-
Supply, Installation, Testing and commissioning of 63 mm dia instantaneous pattern SS short branch pipe, 20 mm dia nozzle conforming to IS 903, suitable for inter connection to hose pipe coupling complete as required by the Local Fire Authority.
4
-
-
Supply, installation, testing and commissioning of First Aid Hose Reel equipment conforming to IS:884 comprising of hose reel drum, 8 mm shut off nozzle, Rubber hose of 25 mm dia x 30 mtr. long, painting, swinging type fixing bracket, anchor fastener, bolts & nuts etc. complete as required by Local Fire Authority
4
-
-
Supply, installation, testing and commissioning of SS Ball Valve.
a) 25mm dia
7
-
-
b) 50mm dia
2
-
-
Supply, installation, testing and commissioning of Cast Iron Four Way Fire Brigade Inlet as per IS: 904 having 63 mm dia inlet with blank cap and chain with necessary fittings, flanges, nut bolts etc. (For Hydrant Network)
1
-
-
Supply, installation, testing and commissioning of Cast lron Two Way Fire Brigade Inlet as per IS: 904 having 63 mm dia inlet with blank cap and chain with necessary fittings, flanges, nut bolts etc. complete as required. (For Water Tank)
1
-
-
Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve with necessary fittings. Size: 25 mm (For Riser)
1
-
-
Supply, Installation, Testing and commissioning of Flow Indicating Switch with fittings, Flanges, nut-bolts, washers etc. as per requirement.
1
-
-
Supply, installation, testing and commissioning of Pump on/off Remote switches to each internal hydrant valve with required accessories.
5
-
-
Supply, installation, testing and commissioning of XLPE insulated copper armoured Cable from each Pump on/off switches to Panel with all necessary accessories. Size: 4 core x 2.5 sq. mm
30
-
-
II) FIRE EXTINGUISHER AND EXIT SIGNAGES
Supply, installation, testing and commissioning of Carbon Dioxide (Co2) type Fire Extinguisher of 4.5 kg confirm to IS:15683, with ISI marked / TAC approved fitted with required accessories including wall suspension brackets.
10
-
-
Supply, installation, testing and commissioning of Dry Chemical Powder (DCP) type 6 kg confirm to IS:15683, with ISI marked / TAC approved fitted with required accessories including wall suspension brackets.
10
-
-
Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes:
a) Exit: size: 4" X 12"
8
-
-
b) Fire Equipment: 4" X 12"
8
-
-
c) Fire Extinguisher: 8" X 4"
8
-
-
26. Non Schedule
-
-
-
Supply and fixing of STRAIGHT PROFILED KALZIP “SELF SUPPORTED” SECRET FIX STANDING ROOFING SYSTEM IN 0.9mm THICK AA 3004 ALUMINIUM ALLOY. The general roof-construction shall comprise of: Top layer – Kalzip 65/400 profiled sheet manufactured from aluminium self supported standing seam roof system manufactured from aluminium alloy AA 3004 (AlMn1Mg1) as specified in BS EN 1396: 2007 minimum material thickness of 0.9 mm and Fluorocarbon PVDF finish on the exposed surface.The material properties shall be as follows: Ultimate tensile strength: minimum 200 N/mm2, 0.2% Proof Stress: min 185 N/mm2, Modulus of elasticity: 70,000 N/mm2. Including Accessories, aluminium ST clips and Fasteners. Sheets are to be laid to meet the requirements of the building geometry and fixed on Aluminum clips. Clip to be fixed to the top hat/purlins with SS 304 screws only. Liner sheet-Colour coated Galvanised steel liner sheet. Vapour Control layer - A single layer of double sided aluminium foil vapour barrier. Insulation - Rock wool insulation of 50mm thickness minimum 48kg/m3 density with thermal conductivity of K=0.04 W/mk at 25 degree Celsius. Fire classification with test procedures to BS 476: Parts 6 & 7.
Supply and fixing of STRAIGHT PROFILED KALZIP “SELF SUPPORTED’’ Ridge.
1690
-
-
Supply and fixing of STRAIGHT PROFILED KALZIP “SELF SUPPORTED’’ Ridge.
390
-
-
Supply and Installation of ASG WIN 84C AS-86, 45* degree Angle Openable Sun louvers System with maximum 27 mm clear gap. 84 C Panels shall be 84mm wide in 0.6 (TCT) mm thickness roll formed out of Aluminium alloy. Panels shall be pre coated with exterior grade powder coating of not less than 60 microns of Akznoble or Jotun as per requirement in colour ANY RAL COLOUR. Carrier module shall be 86mm C/C. Panels shall be clipped on to Aluminium alloy carrier with prongs to hold panels in 86mm module. Panels shall be installed on carrier of thickness 0.9mm is installed at not more than 1000mm c/c . Carrier shall be fixed directly on the MS sub frame
160
-
-
Pedestal pertition
Thickness of Compact Laminate : 12 mm
Color of HPL Boards: Single Colour
Size of Cubicle : 1000MM (W) X
1550MM (D)X 2003 mm(H)
Door Size : 610mm (W)
Overall Height Of Cubicle : 2003 mm
(Including bottom Gap of 150mm)
a) Aluminium “U” Channel
b) Aluminium “F” channel
c) Aluminium Door Stopper Channel
d) Aluminium Top Rail
e) SS Coat Hook
f) SS Lock Set c/w Occupancy Indicator
g) SS Door Knob
h) SS Hinges with Cover
i) SS Adjustable Foot 316 Grade
j) Rubber Door Stopper Lining
k) S.S.Screws 304 G & P.V.C Wall Plugs
28
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements