Military Engineer Services Tender

M & L hardcore of broken stones of gauge n.exc.63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface.

M & L Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete all as specified.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded aggregate as in sub base,complete all as specified and directed.

M&L100mm thick (1:2:4) Type B-1, Plain cement concrete with using 20mm graded aggregate as in hard standing etc finished fair and even without using extra cement , complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in plinth protection & finishing the surface even and smooth with out using extra cement complete all as specified and directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, Set in Cement Mortar 1:6, complete all as specified and as directed.

M&L 10 mm thick rendering plastering in CM 1:6 on brick/ concrete surfaces including finishing the surfaces fair and even complete all as specified and directed.

M&L Rendering 15mm thick plastering in CM 1:4 on any faces of brick work or concrete surfaces including finishing the surfaces fair and even by using WPC as per manufacturer's instructions complete all as specified and directed.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Cement Base Paint (as approved Tint) over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

S&F structural steel work rolled mild steel joist, channel, angle, or tee sections, as in vertical post fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410 W (Gde E-250) quality 'B' complete all as specified and directed.

S&F mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails , fixed with angle cleats or other connecting plates, gusset plates, etc conforming to Gde Fe-410-W (Gde E- 250) quality 'B' complete all as specified & directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.

S & F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment all as specified and as directed.(Fe-250-W(Gde- E-165) quality- A)

M&L mild steel bolt 12mm dia ( machine made) with hexagonal or square beads at one end and screwed the other or screwed both ends each screwed and to be fitted with washers and one hexagone or square but length of bolt n exc 5 cms long complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and as directed.

S&F Hard drawn steel wire fabric n. exc 4.00kg/sqm cut to lengths, bent to shape required and fixing to steel members complete all as specified and as directed

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S & F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M & L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound,Grade ‘A’

S&F mild steel works as in doors or gates of angle or other sectons with gusset plates, rails, braces etc complete drilled, welded etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete.Fe 250 -W (Gde- E- 165)

S&F for Rotational moulded polyethylene water storage tanks 1000 ltr cap.(cylindrical vertical with closed top) hoisted and fixed in position incl 20 mm PTMT ball cock complete all as specified

S&F Gun metal globe or flush cock with iron wheel, screwed both ends for iron pipe 15mm bore.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F 15 mm dia bib tap cast copper alloy (fency type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as directed.

Returning filling in including spreeding, leveling, watering and well ramming in layers n. exc 25 cm thick in soft /loose soil complete all as directed.

Removal of excavated soil not exc 50m and depositing where directed at a level n.exc 1.5m above the starting point all as directed.

M & L for point wiring with 1.5 Sqmm PVC insulated unsheathed 1100 Volts grade multi stranded copper conductor FRLS in PVC casing capping (ISI Marked) (Approx size 20/25/40mm width) along with all fitting/ fixtures as Tee, Bend Elbow socket, Saddles etc. complete with PVC board/ box suitable size / shaped for and accommodating modular switches sockets, regulators in white / ivory/ of white colour and with 1.50 Sqmm PVC insulated copper conductor stranded as earth wire connecting to earth dolly including MS box 3mm thick with 3mm hylum sheet cover for fixing of switches/sockets/fan regulators etc, complete all as specified for the following: -

One ligh/bell/ceiling fan/exhaust fan point controlled by one switch

One 3/5 pin socket 5 Amps on the same board with other switches with cables 1.5 sqmm size.

One 3/5 pin socket 5 Amps, independent, with cables 1.5 sqmm size.

All as per item No 34 above but for 3/5 pin socket outlet 5/15 Amps, independent with 2.5 Sqmm single core PVC insulated unsheathed 1100 Volts grade multi stranded copper conductor FRLS complete with 1.50 Sqmm stranded copper conductor PVC insulated unsheathed earth wire and connecting to earth dolly complete all as specified and directed.

Supply and fixing in t of MCB ,SP 06 to 32 Amps C series 10 KA breaking capacity 240 Volts. Make:- Legrand/L&T/SEMENS.

Supply and fixing in replacement of MCB ,SPN 10 to 40 Amps C series 10 KA breaking capacity 240 Volts. Make:- Legrand/L&T/SEMENS.

S & F LED battern lighting fixture with extruded AI, heat sink, environmental friendly, energy efficient 18/20 watt LED light fitting 4' long including LED Tube sutable for the fitting with all fitting arrangement and accessories, internally pre wired and including connecting with twin core twisted flexible copper conductor cable with suitable size upto ceiling rose complete all as directedabove/Engg- in - Charge. Make: Havells/ Crompton Greaves/Phillips

S & F switch piano flush type single pole, one way 230 Volts AC 5/6 Amps, complete all as specified and as directed.

S&F socket outlet flush type 2 in 1, 3 pin, 5 Amps, 230 Volts AC including necessary connection complete all as specified and as directed.

S & F switch socket combination 5 pin, 5 Amps (multi plug) flush type 230 Volts complete all as specified and as directed.

S & F switch socket combination 5 pin, 5 Amps/16 Amps (multi plug) flush type 230 Volts complete all as specified and as directed.

S & F ceiling rose surface type bakelite 65x50 mm two to three terminal suitable for 230 Volts AC 6 Amps, complete all as specified and as directed.

S & F lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting complete all as specified and as directed.

S & F in replacement of distribution board sheet metal enclosure factory made fixed flush with wall inside the nitches or outside on wall surface suitable for mounting isolators & MCB's etc. 240 Volts, 200 Amps rated bus bar capacity SPN 4 way Double door complete all as specified and as directed. Make -Legrand/L&T/BCH

Supply & fixing LED street light fitting 20W including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED (SEOUL) 6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed including bracket and fixing clamps etc. Make Havells/ Philips/ CG/ C&S

Supply and fixing in replacement of LED 10 watt suitable for fixing in Normal pendent/Batten Holder 230 Volt complete all as specified and as directed. Make:- Havells

Earthing complete with GI earth plate electrode 60cm x 60cm x 6mm thick buried in ground vertically to a depth not less than 2.25 meters below ground level with the top edge of earth plate not less than 1.5 meters below ground level connected to galvanised iron earth wire 4mm dia by means of bolts, nuts, check nuts, washers maade out of galvanised iron steel all as shown in electrical plate No 3 of SSR Part I and earth wire protected by galvanised pipe light grade 15mm bore and connected to LT panel/ pole through test point including necessary earth work and excavation in any type of soil, GI light grade 15mm bore watering pipe with funnel and wire brush, PCC 1:2:4 type B1 chamber with 20mm thick RCC 1:2:4 type B1 , covere slab with 6mm dia MS bars at 100mm c/c both ways with MS hook 6mm dia etc complete all as specified and directed and testing on complete

Supply and laying 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor, served with inner sheathing of PVC tape or overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4 mm dia GI suspension wire, 2 core cable 16 Sqmm stranded aluminium conductor cable flat or circular complete all as specified and as directed.

M & L for Cutting existing steel tubing 50/40 mm for alterations or additions

Supply, laying, jointing & testing for 25 mm bore of galvanized steel water tubes, 'Light grade', ISI marked, galvanized with all fittings, laid in trenches complete all as specified & directed.

S & F 25 mm bore gun metal, globe or gate valves, with iron wheel head (ISI marked), screwed both ends, complete all as specified & directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick burried directly in Ground (Earth Pit not less than 2.25 Metre below Ground Level) with Top edge of the Plate not less than 1.50 Metre below Ground Level, connected with and including Galvanised Earth Strip of size 32x6.0mm by means of Bolts, Nuts, Check nuts and Washers of GI or Steel and connected Earthing Testing Point/Bus-bar with GI 40mm bore (dia) Light grade Protection Pipe, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including Taking down/out Unserviceable Earthing of any description, complete all as per specified and as directed.

Supply, Installation & testing Environmental Friendly Waste Disposal Incinerator system comprising as speceifiied and as directed of followings : - (i) Biofics Organic Waste Composting Machine - Model/Make BF 500, Capacity 500Kg/Day, automatic type, microbes supported composting on high temp based, biomass retention period 3-4 days, compostting cycle time 24 hrs, Brim Capacity 2000Litre, Waste mixing chamber/composting tank ss 304 (min 3 mm thickness sheet), mixing Blades ss 304 (Min 16 paddles with tampered) periodical rotation at low RPM, outer body ss 304, shredder shaft double shaft high strength 4140 alloy steel shredder with capacity 400-500kg/ht x 2 , 13 blades 13 spacers ss 304, MS channel structure frame with inbuilt control panel PLC based (Makes for panel, motor & Heater : L&T/schneider/Siemens/ABB/Havells/kirloskar/crompton), Effluent Bloweer 0.50KW, Effuent filtration MOC ss 304 body and internal piping, agitaor motor power 5 HP, shredder motor 3 HP, compact gear box, Both auto and manual mode, door sensors, temp sensors, moisture sensors, bacteria culture provided for first generation and booosing in future, 30% moisture organic compost, volume reduction should be more than 85%, 01 year electric, 2 year mechanical on site warranty incl 01 year AMC. (ii) Biofics incinerator Unit BI 50 Kg Electric incinerator, Muncipal solid waste, Capacity 50 Kg/Hr, mode of heating electric and manual feeding and ash removal. (iii) Biofics Canveyor Belt- Clint bucket type conveyor, capacity 500 kg/Hr, inbuilt disintegrated control panel, Main motor 2 HP, Minimum 10 ft lenth and 2 feet width, all contact surfaces SS and EN Non - contact surface SS & MS Powder coated and fixed with organic waste composting Machine. (iv) Biofics organic waste shredder :- (a) waste processing capacity per Hr -100-200 kg/hr (b) Appx Dimension ( in feet) ( L x H x W) -3 x 3 x 5 Feet (c ) Power Consumption per hr -1.5 KW appx (d) Motor with planetary Grear Box -03 HP (e) Motor Make -ABB/CG/Bharat Bijili/Havells (f) all contact surfaces SS and EN Non - contact surface SS & MS Powder coated (g) 01 year electric, 2 year mechanical on site warranty incl 01 year AMC, 18 inch blades, PET, PP, PVC, HPE, LDPE, Nylon ABS etc, inbuilt disintegrated panel. (v) Biofics Plastic waste shredder :- (a) waste processing capacity per Hr -100-200 kg/hr (b) Appx Dimension ( in feet) ( L x H x W) -3 x 3 x 5 Feet (c ) Power Consumption per hr -1.5 KW appx (d) Motor with planetary Grear Box -03 HP (e) Motor Make -ABB/CG/Bharat Bijili/Havells (f) all contact surfaces SS and EN Non - contact surface SS & MS Powder coated (g) 01 year electric, 2 year mechanical on site warranty incl 01 year AMC, 18 inch blades, PET, PP, PVC, HPE, LDPE, Nylon ABS etc, inbuilt disintegrated panel.

M&L Cutting Existing Road not exc. 1.50 Metre in depth and not exc. 1.50 Metre wide including Making Good the same to match the Original Surface level with Cement Concrete after laying of Cables, Well Ramming and leveling in layers, etc., complete all as specified and as directed. NOTE : Cement Concrete will be Measured and Paid separtely under appropriate Item.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Foundation, Filling and Mass Concrete, etc. including Use and Waste of Formwork as required/ordered, complete all as specified and as directed.

Supply & Laying XLPE insulated, PVC sheathed, Heavy duty, armoured with multi-stranded Aluminium Conductor Electric Cable, 1100 Volt grade, having Cross-sectional Area 50 Sqmm 3.5 Core, conforming to IS:7098 (Part-1), laid in Tenches or fixing to Electric Poles or Passing through Pipes/ along Walls/ Roof/ across Drains/ Culvert, complete all as specified and as directed. NOTE : Necessary Earth works, Sand cushioning, Cable Protection Cover & GI Pipe, etc. will be Measured and Paid separately under relevent Items

Supply & Laying XLPE insulated, PVC sheathed, Heavy duty, armoured with multi-stranded Aluminium Conductor Electric Cable, 1100 Volt grade, having Cross-sectional Area 35 Sqmm 4 Core, conforming to IS:7098 (Part-1), laid in Tenches or fixing to Electric Poles or Passing through Pipes/ along Walls/ Roof/ across Drains/ Culvert, complete all as specified and as directed. NOTE : Necessary Earth works, Sand cushioning, Cable Protection Cover & GI Pipe, etc. will be Measured and Paid separately under relevent Items

Supply only PVC insulated, sheathed Stranded Copper Conductor Water Proof Cable, Flat, Cross-sectional Area 6.0 Sqmm, 3 Core, 1100 Volt grade, conforming to IS:694 for suitable for Motor Assembly upto 7.5 HP capacity, complete all as specified and as directed.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

M&L Galvanised Steel Tubing Pipe 50mm bore (dia), light grade with Bend, laid in Trenches or under Roads/ Flooring/ Culverts and/or fixing to Electric Poles with suitable size Mild Steel Flat Iron Clamps, Bolts, Nuts, Washers, etc., complete all as specified and as directed.

Supply & Laying Unreinforced Pre-cast Concrete Cable Cover of size 300x180x40mm thick, Class LV, Type 2, Flat, Concrete grade M-20 minimum, complete all as specified and as directed.

Supply, Installation & Commissioning Feeder Pillar Box Factory Made (CPRI approved Manufacturer), made out of 3.15mm thick for Load Bearing and 2.00mm thick for Non-load Bearing CRCA Sheet, Outdoor Cubical type, with Locking Arrangement, Fully Compartmentalized, Totally Enclosed Weather and Vermin Proof suitably ventilated 440 Volts, 50 Cycles, AC Supply having IP-54 Protection as per IS-2147 of 1962 with Pre-treatment and Powder Coated of approved Colour with Mild Steel Angle Iron 40x40x5.0mm Frame Work/ Supports, grouting Legs in Cement Concrete 1:2:4 (20mm graded stone aggregate) Block of size 300x300x450mm including necessary Formworks, Earth Works, etc., Providng all Electric Connections and Testing, complete all as specified and as directed and Comprising with including to accumodating the followings:- (a) Copper Bus-bar 4 Strip, 400mm long, 200 Amp, 415 Volt - 01 Set (b) MCCB 125 Amp, 4 Pole , 25 kA, 230 Volt - 01 No. (c) MCCB 63 Amp, 4 Pole25 kA, 230 Volt - 01 No (c) MCCB 4 Pole 32 Amp, 16 KA Pole, 25 kA, 415 Volt - 03 No. (d) Automatic Star Delta starter 3 Phase for 1-5 HP Motor-03 set (e) Digital Amp Meter 0-40 Amp with CTs of suitable ratio & Selector - 03 No. (f) Digital Volt Meter 0-500 Volt - 01 set (g) Indicating Lamp (RYB), LED type - 01 Set