Military Engineer Services Tender
BidAssist is a very user-friendly website that helps us to explore all the new opportunities so as to achieve growth in our business. It helps us to attain all the information with respect to any e-tender the Arunachal Pradesh government has posted on its website in a very hassle-free manner.
Military Engineer Services - MES Tender
Eprocure
Opening Date31 Aug 2024
Closing Date23 Sep 2024
Tender Amount₹ 33,70,000
Costs
EMD
₹ 67,400Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_669515_1Bid Award Id
ViewTender No
8642/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
REPAIR /REPLACEMENT OF OLD UNSV RUSTED PIPE LINE, PUMP/MOTOR, CLEANING OF OVERHEAD TANK AND CONNECTED WORKS OF EXTERNAL WATER SUPPLY AND REPAIR/ MAINT/ SERVICING TO DG SETS, LT PANELS AND EARTHING AT BORARUPAK I-II MIL STN MIL STN UNDER GE 872 EWS
BOQ Items
Taking up or down 20mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.
242
-
-
Taking up or down 25 or 32 mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.
434
-
-
Taking up or down 40 or 50mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.
350
-
-
Taking up or down 65mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.
642
-
-
Taking up or down 80mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed.
260
-
-
Refixing/Re-laying of 20mm bore old serviceable steel tubing and connections in new or old position with new fittings complete laid in trenches complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 04 above)
20
-
-
Refixing/Re-laying of 25 or 32mm bore old serviceable steel tubing and connections in new or old position with new fittings complete laid in trenches complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 05 above)
40
-
-
Refixing/Re-laying of 40 or 50mm bore old serviceable steel tubing and connections in new or old position with new fittings complete laid in trenches complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 06 above)
40
-
-
Refixing/Re-laying of 65mm bore old serviceable steel tubing and connections in new or old position with new fittings complete laid in trenches complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 07 above)
40
-
-
Refixing/Re-laying of 80mm bore old serviceable steel tubing and connections in new or old position with new fittings complete laid in trenches complete as directed. (Note: Serviceable pipe shall be reused as obtained from serial item No. 08 above)
10
-
-
Supply, laying, connection and testing 20mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
180
-
-
Supply, laying, connection and testing 25mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
130
-
-
Supply, laying, connection and testing 32mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
180
-
-
Supply, laying, connection and testing 40mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
130
-
-
Supply, laying, connection and testing 50mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
180
-
-
Supply, laying, connection and testing 65mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
560
-
-
Supply, laying, connection and testing 80mm bore, Steel water tubing, galvanised, medium grade with all fittings, laid in trenches, etc complete all as specified and directed. (Note: Excavation and earth work work shall be measured and paid seperately)
190
-
-
Supply, laying, connection and testing, 20mm outer dia 3- layer PP-R Polypropylene random copo-lymer) pipes SDR 7.4 & PN16 stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed
42
-
-
Supply, laying, connection and testing, 25mm outer dia 3- layer PP-R Polypropylene random copo-lymer) pipes SDR 7.4 & PN16 stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed
42
-
-
Supply, laying, connection and testing, 32mm outer dia 3- layer PP-R Polypropylene random copo-lymer) pipes SDR 7.4 & PN16 stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed
42
-
-
Supply, laying, connection and testing, 63mm outer dia 3- layer PP-R Polypropylene random copo-lymer) pipes SDR 7.4 & PN16 stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed
42
-
-
Supply, laying, connection and testing, 90mm outer dia 3- layer PP-R Polypropylene random copo-lymer) pipes SDR 7.4 & PN16 stablised and antimi-crobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings laid in trenches complete all as specified and directed
60
-
-
S & F in repairs, 20 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.
10
-
-
S & F in repair 25 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.
20
-
-
S & F in repair 32 mm bore, gun metal, globe or Gate valves with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.
10
-
-
S & F in repairs, 40 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed.
10
-
-
Dismantling joints of flanged pipes in position, 80 mm bore including removing old rubber or fibre board gaskets, bolts, nuts. etc. to store complete all as specified and directed
4
-
-
S & F in repairs, 80mm bore, GI Nipple 150mm long with nuts, bolts and rubber gasket complete all as specified and directed.
15
-
-
S & F 50mm bore, cast iron sluice valve, non-rising stem type, both end flanged, class PN 1.6 conforming to IS -14846-2000 with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out/down existing one complete all as specified and directed.luding taking out existing one complete all as specified and directed.
4
-
-
S & F 65mm bore, cast iron sluice valve, non-rising stem type, both end flanged, class PN 1.6 conforming to IS -14846-2000 with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out/down existing one complete all as specified and directed.luding taking out existing one complete all as specified and directed.
4
-
-
S & F 80mm bore, cast iron sluice valve, non-rising stem type, both end flanged, class PN 1.6 conforming to IS -14846-2000 with iron wheel head and stainless steel spindle including necessary jointing materials like nuts, bolt, washer & rubber/fiber board gasket including taking out/down existing one complete all as specified and directed.luding taking out existing one complete all as specified and directed.
3
-
-
Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
0.5
-
-
S & F Rolled mild steel work as Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.
25
-
-
S & F Mild steel screw bolts of 5 to 10mm dia of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10cm and n. exc 15cm long complete all as specified and directed.
25
-
-
M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of aluminium paint over a coat of red oxide, zine chrome primer complete all as specified and directed.
5
-
-
M & L for construction of brick masonry valve pit of size 45 cm x 45 cm x 45 cm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation & earth work in soft/loose soil and demolition of existing one complete as specified and directed all as per relevant TD drawing. (Note : Drawing not attached with the tender document. However, the same can be seen in GE/AGE E/M office during working hours)
4
-
-
M & L for construction of brick masonry valve pit of size 60 cm x 60 cm x 60 cm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3.15mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation & earth work in soft/loose soil and demolition of existing one complete as specified and directed all as per relevant TD drawing. (Note : Drawing not attached with the tender document. However, the same can be seen in GE/AGE E/M office during working hours)
4
-
-
M & L for construction of brick masonry valve pit of size 90 cm x 90 cm x 90 cm (internal dimension) one brick thick wall in CM 1:4 on 100mm thick PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundation, 15mm thick rendering in cement mortar (1:4) internally, externally up to 15cm below GL, providing valve pit cover made out of 3mm thick MS sheet duly welded with provision of hinges, handle and locking arrangement including 40 x 40 x 5mm angle iron frame fixed on top of valve pit by means of hold fast 150mm long, embedded in PCC block 1:2:4 type B-1 (20mm graded aggregate) of size 230 X 200 X 100mm, applying two coats of anti-corrosive paint over a coat of red oxide, zinc chrome primer after preparation of steel & iron surfaces including necessary excavation & earth work in soft/loose soil and demolition of existing one complete as specified and directed all as per relevant TD drawing. (Note : Drawing not attached with the tender document. However, the same can be seen in GE/AGE E/M office during working hours)
3
-
-
M & L for dewatering water from Pre Sedimetation tank, 5 KL capacity, cleaning and removing all mosses, Algae, dirts etc from the walls and floor of water tank, removal of dirty water with sludges and disposed off from the site as diretced, rubbing walls, floor, ceiling surfaces with wire brushes/gunny bags after sprinkling sufficient quantities of bleaching powder and washed thoroughly with fresh water including cleaning of outlet pipes, stop valves, gate valves after taking out pipe lines with stop valves, gate valves etc and all accessoires, re-fixing the same after cleaning including float valves wioth float arm to orginal position, writting letters as "TANK CLEANED ON : DD/MM/YY"(i.e date of cleaning) of size exc 100mm but n.exc 200mm in height and 15mm in wide with white paint on black back ground on the front/road side/face of the tank complete all as specifed and as directed.
2
-
-
All as per Serial item No. 42 above but 11 KL capacity Pre Sedimentation tank complete ditto.
2
-
-
All as per Serial item No. 42 above but 40 KL capacity Pre Sedimentation tank complete ditto.
2
-
-
All as per Serial item No. 42 above but 84 KL capacity Pre Sedimentation tank complete ditto.
2
-
-
S & F in repair of water pressure gauge diaphram type range 0-7 Kg/Sq cm 100 mm dia complete all as directed by Engineer-in-Charge.
3
-
-
Supply only High strength calcium Hypo Chloride, 65-70% chlorine content, Calcium based granular disinfectant for water treatment chemical complete all as specified and directed. (Note: Make shall be as per approved makes of E-in-C. Testiting certifcate of chemical shall be submitted by the contractor before supply).
600
-
-
M & L for Repair/ Maint, Servicing of Diesel engine generating set of capacity 30 KVA of Make:- Kirloskar, 1500 RPM, Air cooled/Water cooled consisting of the following works:-
(a) Replacement of all Filters, Lubricating Oil.
(b) Checking of Belt Tension, Battery Connections and Topping up Distilled Water (if required), External Bolts and Nuts and its Tightening, Safety Units and its Electrical Connections, Alternator Cable Connections, Engine Control Wirings
(c) Carry out necessary Tappet Clearance, if required.
(d) Cleaning of Fuel Lines, Inlet Air Lines and Exhaust Liner Radiator Fins.
(e) Check functioning of Changing Alternator.
(f) Engine Safety viz. High Water Temperature Gauge, Oil Pressure Gauge, Oil Temperature Gauge and High Speed Gauge shall be checked for their functions and repaired/replaced if required.
(g) Coolant Level and Conditioning of Coolant shall be checked and refilled if required.
(h) The Governor shall be Checked and Tuned for Proper Functioning.
(j) Check for Leaks if any and shall be rectified.
(k) The Engine shall be Run on NO LOAD or at AVAILABLE LOAD, Check any Leakage and Abnormal Noise. If any such abnormality Noticed the same shall be Diagnosed and Remedial Action shall be taken to removed the casues.
NOTE : (a) Replacement of Consumable Items such as Distilled Water, Lube Oil, Grease etc are deemed to be included in the unit quoted rate. (b) All Other Spare Parts (Quantitites mentioned under supply only items here-in-after are Provisional only) and will be Measured & Paid seperately as 'Supply only' under appropriate Items. Labour element for the same shall deemed to be included in the unite quoted rate)
3
-
-
All as per serial item No. 47 above but for 15 KVA DG set of make Ashok Lyland complete ditto
1
-
-
Supply only Air Filter Assembly including Fliter (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
2
-
-
Supply only AVR (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
2
-
-
Supply only Bearing for cooling fan and fan belt (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
3
-
-
Supply only Controler Model No. KG934 (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
1
-
-
Supply only Cooling fan (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
2
-
-
Supply only Door Hinges with Nut & Bolts (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
6
-
-
Supply only Fuel Filter Assembly including Filter (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
2
-
-
Supply only Fuel Pipe (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
3
-
-
Supply only Oil Filter Assembly including Filter (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
2
-
-
Supply only V Belt (as per existing/ as approved) suitable for DG Set 30 KVA complete all as specified and as directed.
1
-
-
Supply only Air Filter Assembly including Fliter (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only AVR (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Bearing for cooling fan and fan belt (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Controler Model No. KG934 (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Cooling fan (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Door Hinges with Nut & Bolts (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Fuel Filter Assembly including Filter (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Fuel pipe (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only Oil Filter Assembly including Filter (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
Supply only V Belt (as per existing/ as approved) suitable for DG Set 15 KVA complete all as specified and as directed.
1
-
-
S & F in repair Asbestos Rope (as per existing/ as approved) complete all as specified and as directed.
10
-
-
S & F in repair Battery Terminal of Copper/Brass (as per existing/ as approved) and connected complete all as specified and as directed.
3
-
-
S & F in repair Toggle Switch 3-way, Double Pole (as per existing/ as approved) and connected complete all as specified and as directed.
1
-
-
M & L for Cleaning of Radiator of any Capacity after Opening all Nuts, Bolts, etc. by dismounting, Re-mounting after Cleaning with Chemical and Tightening of Nuts, Bolts, etc. including Straightening of Radiator Fins with suitable Tools, complete all as specified and as directed.
4
-
-
M & L for Repairing & Cleaning of Diesel Tank with suitable Materials after disconnecting Fuel Line, Opening of all Nuts, Bolts, etc., Re-fixing the same after satisfactory Repairing including necessary Welding (if required), etc., complete all as specified and as directed.
4
-
-
Supply & Filling Coolant for Radiators as approved complete all as specified and as directed.
(MAKE : KIRLOSKAR or equivalent Make as approved by GE)
20
-
-
Supply & Filling Engine Oil 20 W/ 40 Grade as approved, complete all as specified and as directed.
(MAKE : CASTROL CRB PLUS or equivalent Make as approved by GE)
40
-
-
S & F in repair on load Change over switch, with SS enclosure, current rating 125 Amps, 4 pole, 415 V, 50 Hz complete all as specified and directed. (Make: Havell's Cat No. IHCNFE0125 or equivelant approved make as per list of manufacturer)
2
-
-
S & F in repair on load Change over switch, with SS enclosure, current rating 63 Amps, 4 pole, 415 V, 50 Hz complete all as specified and directed. (Make: Havell's Cat No. IHCNFE0063 or equivelant approved make as per list of manufacturer)
1
-
-
M & L for repair/ overhauling of electric panel board including replacement of defective spare/parts such MCCB, MCB, CT, voltmeter, Amp meter, frequency meter, indicator lamps etc including necessary welding to doors, replacement of defective wire, lugs etc and spray painting with one coat of synthetic enamel pait (1st grade quality) complete all as specified and directed. (Note : (i) Spare parts shall be measured and paid seperately as supply only. (ii) The cost of cleaning, painting and replacement of minor spare such as lugs, wire etc shall deemed to be included in the unit quoted rate).
8
-
-
Supply only Digital Voltmeter 0-500 volts with built in selector switch of dial size 96 x 96mm with accuracy class 1.0 including complete all as specified and directed.
5
-
-
Supply only digital ammeter with built in selector switch 0-500 Amps of dial size 96x96mm with accuracy class 1.0, three phase complete all as specified and directed.
5
-
-
Supply only MCCB 415 Volt, 25 KA, 4 Pole, 200 Amps Capacity, adjustable thermal and magnetic release complete all as specified and as directed. (Make: Havell's Cat Part No. IHLANDC40200 or equivelant of make as per List of Manufacturer's)
6
-
-
Supply only MCCB 415 Volt, 25 KA, 4 Pole, 100 Amps Capacity, adjustable thermal and magnetic release complete all as specified and as directed. (Make: Havell's Cat Part No. IHLASDC40100 or equivelant of make as per List of Manufacturer's)
6
-
-
Supply only CT's Cast Resin type of ratio 100/5 Amps suitable for electric panel complete all as specified and as directed. (Make: AE/L & T or equivelant of make as per List of Manufacturer's)
3
-
-
Supply only MCB 4 pole 63 Amps, 240 Volts, 10KA, C curve complete all as specified and as directed (Make: Havell's cat part No. DHMZCFPF063 or equivalent make as per List of Manufacturer's)
2
-
-
Supply only MCB 4 pole 40 Amps, 240 Volts, 10KA, C curve complete all as specified and as directed (Make: Havell's cat part No. DHMZGCFPF040 or equivalent make as per List of Manufacturer's)
10
-
-
Supply only Neon indicator lamp for panle board complete all as specified and as directed
5
-
-
M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 32x6mm by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 40 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab of size 350x350x50mm (reinforced with 10 mm dia deformed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion inclduing taking down old one complete all as specified and as directed by the Engineer-in-Charge.
4
-
-
M & L Earthing complete with copper earth plate electrode 600 mm x 600mm x 3.15 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with copper earth strip of size 20x3mm by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 40 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion inclduing taking down old one complete all as specified and as directed by the Engineer-in-Charge.
6
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements