Municipality Tender

Manufacture, SuppLy, Delivery and fixing of furniture;Accounts Room Supply and installation of Workstation 1500x1500x600 side by side GRIHA Certified HYBRID SYSTEM- 52 mm Thick Main Spine . The uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm. this shall be coated with min. 45 micron thickness of epoxy powder coating.52 mm thk panel to be provided with two top tiles 1 nos White Board and 1 no magnetic fabric tile above the table top . Middle 2 Blocks of the Main partition should have - blocks made of honeycomb structure wrapped outside with fabric , Bottom Tile should be of - Metal. . panels elevated from floor by 120 mm , . .Wire Management - Electrical switches to be mounted above table top & Data on bottom Metal tile. Work top- Made of 25 mm thk prelaminated particle board with 2 mm thick edge band Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Workstation 1500mmWx1500mmWx600mmD , Four person + cluster GRIHA Certified HYBRID SYSTEM-of 52 mm Thick Main Spine workstation . The uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm. this shall be coated with min. 45 micron thickness of epoxy powder coating.52 mm thk panel to be provided with two top tiles 1 nos White Board and 1 no magnetic fabric til Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Freestanding Pedestals (646ht x 390w x 435d), Metal pedestal - 3 draw = 2box + 1 file Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Metal KBPT with mouse tray in Satin Ral white colour Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Full Back Size : 45.5 cm. (W) x 53.0 cm. (H) *Seat Size :48.5 cm. (W) x 49.0 cm. (D) The HR polyurethane foam used in seat and back cushion is moulded in Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "5" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-am)de form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Storwel shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ?D? grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Mayfair Main Desk size shall be 1350 Width x 750 Depth x 750 Height. The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT. The Modesty panel shall be in a combination of black & white cedar with 2 door drawer unit Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: ? 360° revolving type. ? 17° ±2° maximum tilt on pivot at centre ? Upright position locking. Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of visitor chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation table size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.Return unit size shall be 1050 Width x 450 Depth x 705 Height. The top of Finesse ERU -3616 LHS shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm thk. hot pressed plywood OCP-QLTA-PL14-18.The Back should be made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D) BACK SIZE :45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. ARMRESTS : The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TPE). LUMBAR SUPPORT ASSEMBLY: The Lumbar support consshould be ts of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features. ? 360° revolving type. ? Single point control. ? Front-pivot for tilt with feet resting on ground ensuring more comfort. ? Tilt tension adjustment. ? 4-position locking with anti-shock feature. ? Seat/back tilting ratio of 1:2. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia should be Ø66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of visitor chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Workstation 1200mmWx600mmD: GRIHA Certified HYBRID SYSTEM- 52 mm Main Spine Thick workstation . The uprights and horizontals shall be made of aluminum extrusion having material AL96063-T6 & have average wall thickness of 1.2 mm & powder coated with epoxy-polyester powder. Fabricated bottom frame for 52.4mm shall comprise of L- Channels made of 2mm thick CRCA steel (IS:513), formed plates of 3mm thick HR steel (IS:2062) & ERW steel tube of size 35x15x1.6mm in oval cross section (IS:7138) welded together. This shall be coated with average 50 to 60 micron thickness of epoxy powder coating. This shall be bolted to the uprights with M6 screws. legs shall be fabricated by CO2 welding MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube) with the base plate of the MS plate of which an M8 Leveler shall be fitted, which shall allow for adjustment of the height by 50mm. this shall be coated with min. 45 micron thickness of epoxy powder coating.52 mm thk panel to be provided with two top tiles 1 nos White Board and 1 no magnetic fabric tile above the table top . Middle 2 Blocks of the Main partition should have - blocks made of honeycomb structure wrapped outside with fabric , Bottom Tile should be of - Metal. . panels elevated from floor by 120 mm , . .Wire Management - Electrical switches to be mounted above table top & Data on bottom Metal tile. Work top- Made of 25 mm thk prelaminated particle board with 2 mm thick edge band. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Freestanding Pedestals (646ht x 390w x 435d), Meta pedestal - 3 draw = 2box + 1 file Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Metal KBPT with mouse tray in Satin Ral white colour Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of high back chair with The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Full Back Size : 45.5 cm. (W) x 53.0 cm. (H) *Seat Size :48.5 cm. (W) x 49.0 cm. (D) The HR polyurethane foam used in seat and back cushion is moulded in Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "5" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-am)de form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of TABLE Main Desk size shall be 1200 Width x 600 Depth x 743 Height . Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation hinge door(HDU) unit size shall be 1280 Width x 425 Depth x 705 Height. Top of HDU - 4315 shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: ? 360° revolving type. ? 17° ±2° maximum tilt on pivot at centre ? Upright position locking. Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm. Height - min 89.5 to max 100.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Examiner Supply and installation of table size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading.Return unit shall be 1050 Width x 450 Depth x 705 Height. The top of ERU shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm thk. hot pressed plywood OCP-QLTA-PL14-18.The Back should be made up of injection moulded glass filled nylon & upholstered using Net fabric with high tenacity yarn. SEAT SIZE: 47.0 cm. (W) x 51.5 cm. (D) BACK SIZE :45.0 cm. (W) x 65.3 cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf for 25% compression. ARMRESTS : The armrests have an Up-Down adjustment of 8.5 ± 0.5cm which should be provided in armrest structure. Armrest Top has an integrated layer of Thermoplastic Elastomer (TPE). LUMBAR SUPPORT ASSEMBLY: The Lumbar support consshould be ts of polypropylene pad with moulded polyurethane foam & covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pad. Lumbar pad has an adjustment of 8.0 ± 0.5 cm in height. FRONT PIVOT SYNCHRO mechanism: The adjustable tilting mechanism should be designed with the following features. ? 360° revolving type. ? Single point control. ? Front-pivot for tilt with feet resting on ground ensuring more comfort. ? Tilt tension adjustment. ? 4-position locking with anti-shock feature. ? Seat/back tilting ratio of 1:2. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia should be Ø66.1 ± 0.5 cm (76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of visitor chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Commissioner CC Room Mayfair Main Desk size shall be 1350 Width x 750 Depth x 750 Height. The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT. The Modesty panel shall be in a combination of black & white cedar with 2 door drawer uni Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D).BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm (W) x 60.5 cm (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTRE-TILT mechanism: The mechashould be m should be designed with the following features: ? 360° revolving type. ? 17° ±2° maximum tilt on pivot at centre ? Upright position locking. Tilt tension adjustment. . PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSY: The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black nylon Overall Dimensions of Chair Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation Storwel shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ?D? grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of public seating chair SEAT SHELL : The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H) UNDERSTRUCTURE ASSEMBLY: Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment ARM REST ASSEMBLY: Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT 40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame. Overall Dimensions of Chair Seat Height - 44.1 cm. Height - 78.5 cm. Width & Depth of Chair as - Width-169.5cm and Depth-63.8 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Commissioner Room Supply and installation sofa(3+1+1) of sofa 1 seater-92cm(w)*87cm(d)*78cm(h)*43cm(sh). 3 seater-175cm(w)*87cm(d)*78cm(h)*43cm(sh). STITCHING: THREAD : Poly Proplin, PVC. Thickness (mm) : 0.9. Weight (GSM) : 575. FRAME MATERIAL Moisture Content ( 10 ? 12 %) : 16-20%. Thickness of Plywood used(mm) : 12mm & 18mm. SEAT FOAM: (DENSITY, TYPE)-Thickness (mm) : 69, 22 & 10 mm. Density (Kg/m3)- 32d. Type of Foam : Vergin Always / in some case Moulded - Dencity :- 48d. LEG MATERIAL: * Fixing of Leg : Woodscrew provided on frame in addition to M-8 / T-Nut * Material of leg - Plastic * Bush for Leg bottom : Pvc. Bush .BACK FOAM: (DENSITY, TYPE) -Thickness (mm) : 45 mm .Density (Kg/m3): 28 d .ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm .Density (Kg/m3): 26 d Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of center table of overall Size : Width : 107cm Depth : 81.5cm Height : 46cmTABLE METERIALS & SIZE :TOP:SOLID TABLE TOP , LEGS:SOLID RUBBER WOOD Color :WENGE Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of corner table of overall Size : Width : 60.5cm Depth :60cm Height : 46cmTABLE METERIALS & SIZE :TOP:SOLID TABLE TOP , LEGS:SOLID RUBBER WOOD Color :WENGE Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of hinge door unit(HDU shall be 1280 Width x 425 Depth x 705 Height. HDU - 4315 shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of Main table 1800mmWx900mmDx750mmH, Return table(1200mmWx500mmDx750mmH) with Work surface : Made of combination of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under- structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to I8-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of high back leather chair SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. *HIGH BACK SIZE : 47.5 cm. (W) x 77 cm. (D) ARMRESTS (FU3201,FU3202): The armrest top is moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM (FU3201,FU3202): The adjustable ting mechanism is designed with the following features: ? 360° revolving type. ? Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. ? Tilt tension adjustment can be operated in seating position. ? 5-position Tilt limiter giving option of variable tilt angle to the chair. ? Seat/back tilting ratio of 1: 2 ? The mechanism housing is made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT (FU 3201/FU3202): Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT (FU3201/FU3202): Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT (FU3201/FU3202): The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.).TWIN WHEEL CASTOR (FU3201,FU3202) : 5 Nos. twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair with seat slideSEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. * MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) * SEAT SIZE: 49.0 cm. (W) x 51.4 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features : ? Up-Down adjustment? 8 steps (8.0±0.5cm range) ? Height adjustable armrest structure which is chrome plated & fitted with an armrest top. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. ? 360° revolving type. ? Single point control. ? Front-pivot for tilt with feet resting on ground ensuring more comfort. ? Tilt tension adjustment. ? 4-position locking with anti-shock feature. ? Seat/back tilting ratio of 1:2. BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY WITH CASTORS: The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTOR: The twin wheel castors are injection moulded in black PP. OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontaly as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Deputy Mayor Supply and installation of Main table 1800mmWx900mmDx750mmH, Return table(1200mmWx500mmDx750mmH) with Work surface : Made of combination of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Softclosing access flap with in-build power box are provided on work surface for wire management. Modesty Panel : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Under- structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to I8-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedstal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestal is provided with lock for security. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of high back leather chair SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. *HIGH BACK SIZE : 47.5 cm. (W) x 77 cm. (D) ARMRESTS (FU3201,FU3202): The armrest top is moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM (FU3201,FU3202): The adjustable ting mechanism is designed with the following features: ? 360° revolving type. ? Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. ? Tilt tension adjustment can be operated in seating position. ? 5-position Tilt limiter giving option of variable tilt angle to the chair. ? Seat/back tilting ratio of 1: 2 ? The mechanism housing is made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT (FU 3201/FU3202): Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT (FU3201/FU3202): Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT (FU3201/FU3202): The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.).TWIN WHEEL CASTOR (FU3201,FU3202) : 5 Nos. twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair with seat slideSEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. * MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) * SEAT SIZE: 49.0 cm. (W) x 51.4 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features : ? Up-Down adjustment? 8 steps (8.0±0.5cm range) ? Height adjustable armrest structure which is chrome plated & fitted with an armrest top. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features. ? 360° revolving type. ? Single point control. ? Front-pivot for tilt with feet resting on ground ensuring more comfort. ? Tilt tension adjustment. ? 4-position locking with anti-shock feature. ? Seat/back tilting ratio of 1:2. BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY WITH CASTORS: The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTOR: The twin wheel castors are injection moulded in black PP. OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontaly as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Council Hall Supply and installation of table 1350mm W X 600mm D X 740mm H table of Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure : It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes as shown above. Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns) Wire Management : An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables on to worktop and connect devices charger to power socket below worktop.(75 seater) Accessories are provided for adding functionality to the products. Document Shelf is made of 1.2mm CRCA MS IS:513 and is epoxy polyester powder coated (DFT 40-60 microns). It is to be used for storing papers and accessing them quickly. HDMI Wire Cover is made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns). HDMI Holder is made of 2mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns). The HDMI wire cover along with HDMI holder (part of same packet) to be booked for every provision for HDMI connection as per customer/AV team requirement (except in head and corner module). Name plate is provided to display the name of person and consists of two plates - Inner and Outer plate. They are made of 1.2 mm Aluminium sheet and 2mm Aluminium sheet respectively. They are tack welded to each other using Tungsten Inert gas Welding. The Name Plate is epoxy polyester powder coated (DFT 40-60 microns). Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of visitor chair with SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. . TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of table of 1200mmWx600mmDx750mmH with Work Surface :Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Gromet provided on work surface for wire management. Modesty Panel : Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Understructure : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door Storage : Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Handle is provided for ease of opening. Storage is provided with lock for security. Like godrej interio

Manufacture, SuppLy, Delivery and fixing of furniture;Supply and installation of mid back chair with SEAT ASSEMBLY/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with foam laminated fabric and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression. The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with foam laminated fabric. Seat SIZE : 46.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 46.6 cm. (W) x 75.6 cm. (D) ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). ACTIVE BIO-SYNCHRO mechanism:The adjustable tilting mechanism should be designed with the following features: o 360° revolving type. o Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. o Tilt tension adjustment can be operated in seating position. o 5-position Tilt limiter giving option of variable tilt angle to the chair. o Seat/back tilting ratio of 1: 2 o The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY : The pedestal should be injection moulded in black 33% glass-filled Nylon 66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.1±0.5 cm. pitch-center dia.(76.1±1.0 cm. With castors.) TWIN WHEEL CASTOR: 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. Overall Dimensions of Chair Seat Height - 44.2-54.2cm. Height - 113.4-130.9cm. Width-76.1 cm and Depth-76.1 cmm Like godrej interio