Military Engineer Services Tender

Use and removal of formwork to sides of pillars, posts, struts, piers,columns, for rough finished surfaces of concrete

M&L for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in foundation, footings, foundation beams etc.

M&L for reinforced cement concrete M-30 design mix using 20 mm graded stone aggregate as in columns, pillars, piers, posts and struts

M&L for PCC type B1 (1:2:4) using 20 mm graded aggregate as in copings.

M&L for reinforcement steel TMT bars 10 mm dia and over cut to length bent to shape required incl crancking spirally for hooping for columns hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for reinforcement steel TMT bars 5mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders all as specified.

M&L for 5 mm thick cement plaster in 1:4 on fair faces of concrete surfaces finished even and smooth without using extra cement.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc 25 cm in soft/loose.

Removing excavated materials exc 250m and n.exc 500m depositing where directed at a level n.exc 1.50m above the starting point

S&F of Rolled mild steel Framed work Fe 410-W (Gde E-250) quality A as in doors or gates of angle or other section with gusset plate , braced etc complete drilled for fixing steel sheeting or other covering and hinges or steel hanging door fitting complete

M&L for Preparation of newly plastered surfaces of wall and applying two coats of cement base paint, white or tinted over a priming coat.

M&L for Preparation of new steel and iron surfaces of any description over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer

Excavation over Areas n.exc 1.50m deep and getting out in soft/loose soil.

Rolling and consolidating formation surfaces in cutting with power roller 8-10 tonne complete all as directed

M&L for 150mm thick soling (or sub base) with broken boulders or quarried stone, interstices of granite filled, surface formed and rolled and consolidated to required gradient and camber

M&L for 250mm thick (Compacted thickness) in two layers WBM, with coarse aggregates required of Grading 2( 63 to 40mm size), spread, rolled and consolidated to gradient and camber

Applying evenly premixing /tack coat with bituminous primer @ 10kg per 10 sqm using paving bitumen.

M&L for premix bituminous macadam by paving bitumen of any penetration laid rolled and compacted to required gradient, camber ( Consolidated thickness 75 mm or less) all as specified and directed.

M&L for Bituminous premix asphaltic Semi dense concrete 30mm consolidate thickness with 5.5% binder content by weight of total mix, rolled and compacted to required camber and gradient complete using paving bitumen any penetration as binder.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregates as in Kerb stones etc set in CM 1:4

M&L for Moorum filling in floors, laid in layers n.exc 15cm thick, Spread, levelled and rammed including watering

Providing & Fixing of Solar Road Studs Type : Solar Road stud Source of Illumination: Super Bright LED Battery Type : Ni-cd rechargeable Maximum Load : 20 Tons approx, Weight (Kg) : 0.58 kg Protection class : IP68, Features: Improved driver reaction times. Avoidance of sudden breaking and last minute vehicle collision. Reliable and compact design. a permanent source of light on the Road. No. of LED: 6.0 Dimensions (mm): 132x122x75 mm Panel Wattage(W): 0.4 W, Applications: Used to save life and Reduced accidents on the Road by Providing up to a ten-fold increase in visibility. Battery Voltage: 1.2 V Battery Current Rating (mA): 1400 mA , Working Time: 72 Hrs, Life:3 year , Power supply:- monocrystalline solar cell, efficiency over 16% Shell material :- Die-catted aluminium, Battery:- 1.2 V 1200mAH Ni-Mh high temperature resistant battery , Lighting Time :- If charged for 8 hours in standard strongness sunshine, for flash model can be light for continuous 72 hours. , Lighting mode :- flash (2Hz + - 20%) Light colour :- Red, Light source ultra bright Fog applied LED's Visual distance :- 500m , Normal service time:- 3yrs Working temperature :- -10 degree Celsius to + 70 degree Celsius. Can be fixed with Epoxy (Make - Alcolite, 3M or Avery Dennison )