Andhra Pradesh Medical Services And Infrastructure Development Corporation Tender

150 KVAR APFC PANELS IN SUB-STATION Supply Installation Testing & commissioning of free standing floor mounted dust and vermin proof compartmentalised cubical panel made out of CRCA sheet, required hardware, duly painted by two coats of zinc/red oxide primer followed by Powder coated/epoxy/PU painted with phosphatisation in grey or required shade after rinsing. The panel having PU/Neoprene rubber gasket of not less than 3mm thickness,separate detachable, gland plate M.S. base channel, hinged door with locking arrangement for equipment/ switchgear. Thickness of sheet shall not be less than 1.6mm up to 600mm length/width of any compartment and be of 2.0mm above 600mm. Load bearing structure shall be of 2.0mm thick sheet supported by base M.S. channel if required. Side walls and cable alley compartments having bolted type doors with detachable extension type structure, with proper ventilation arrangements for power capacitors with ventilating fans and louvres for natural cooling with required size of G.I. earth bus bar etc., complete. (only outer area on all sides shall be measured and panel to be fabricated from CPRI approved fabricator). Incomer :- 400A TPN, MCCB of adjustable, confirms to IEC 60947-2 and IS 13947-Part 1&2 having Breaking Capacity 35/36 KA with thermal magnetic release Panel Mounted. Makes: L&T- D shine / Schneider-CVS/Legrand –(DP X3/DRX)/ Siemens- 3VL / Hager-h3/ -1 no Supply of 63A/60A, 3 Pole, Adjustable, Confirms to IEC 60947-2 and IS 13947-Part 1&2 having Breaking Capacity 16 KA with thermal magnetic release Panel Mounted. Makes: L&T- D shine / Schneider-CVS/Legrand –(DP X3/DRX)/ Siemens- 3VL / Hager-h3 -5no Supply Installation Testing and commissioning of self healing MPP/MP type shunt capacitor (banks) conforming to IS:13340-41 / IEC :831-1&2 in existing panel or parallel with load terminals , the capacitor shall be fitted with discharge resistors, pressure sensitive disconnector (PSD) and shall have dissipation factor less than 0.0025 at 50 Hz and total wattage loss less than 0.5 Watt per KVAR. including making connections with suitable capacity conductors/ cables testing as required, Heavy duty Three phase 440 V , 50 Hz capacitor (Bank). Makes: L&T/Seimens/Epcos/ Schneider/ Havells

Supply and Fixing of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current ,conforming to IS:13947-4-1/IEC:947-4-1, Din rail mounting type ncluding making onnections, testing etc. as required. suitable for 10 KVAR capacity capacitor bank. Make:Seimens/ABB/Schneider/L&T/C&S/HPL/Havells-2no vells KEI/Polycab/Gloster/Goldmedal/GM Supply and Fixing of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current ,conforming to IS:13947-4-1/IEC:947-4-1, Din rail mounting type ncluding making onnections, testing etc. as required. suitable for 20 KVAR capacity capacitor bank. Make:Seimens/ABB/Schneider/L&T/C&S/HPL/Havells-2no Supply and Fixing of 440 Volt 3 pole capacitor (AC 6 B ) duty contactor with 3 no. early make and post break auxiliary contacts in series with quick discharge damping resistors/ reactors to limit the inrush current ,conforming to IS:13947-4-1/IEC:947-4-1, Din rail mounting type ncluding making onnections, testing etc. as required. suitable for 30 KVAR capacity capacitor bank. Make:Seimens/ABB/Schneider/L&T/C&S/HPL/Havells-3no Metering:- Supply and Fixing of (0-500) V range Volt meter on existing panel, making connection by PVC insulated copper conductor with PVC sleeves/channel etc., as required. Make:Conzerve/Elmeasure/ Meco/ HPL/L&T/ Socomec-1no Supply and Fixing of CT operated direct reading type Ammeter, below 500A, on existing panel , making connection by PVC insulated copper conductor with PVC sleeves/channel etc. as required. Make: Conzerve/Elmeasure/Meco/HPL/ L&T/ Schneider/AE/ Socomec-1no Supply and Fixing of Current Transformer, from 200 / 5 to 500/5 Ratio , 15 VA , class 1 accuracy with all necessary support in existing panel including connection etc. as required Make: Kappa/L&T/ Seimens/ C&S/ Schneider-3no Supply and Fixing of 240/220 V, LED (22.5 mm dia) Pilot lamp Red & Yellow Colour with integral circuit, terminal block, including connection etc. as required for capacitor ON and OFF + Supply indication

Supply and Fixing of 240/220 V, LED (22.5 mm dia) Pilot lamp Blue Colour with integral circuit, terminal block, including connection etc. as required for supply indication Supply and Fixing of selector switch for voltmeter (4 position) including making connection etc. as required. Make: L&T / C&S/ Salzer/HPL-1no Supply and Fixing of CT linked selector switch of 10 A for Ampere meter (4 position) including making connection etc. as requiredMake: L&T/C&S/Salzer/ HPL-1no Supply and Fixing of Cam operated rotary switches on existing panel with 2 way and off position, one pole, 32A. (auto mannual selector switch for capacitors) Make: Conzerve/Elmeasure/ Meco/HPL/L&T/Schneider/AE/Socomec-7no Supply and Fixing of Non-Luminious type, push button actuators and integral contact block of dia. 22.5 mm including making connection etc. as required Make:Seimens/ ABB/ Schneider/ L&T/ C&S/HPL-14no 10 kA - 6-32A range SP MCBs. Makes: Legrand-DX3 / Schneider-A9/Hager-h3/ Siemens-5SX4/ Havells STADx /L&T-AU/Indo Asian-Opti pro/ HPL (Techno) -6no Supply Installation Testing and commissioning of microprocessor based intelligent power factor correction relay having sensitivity up to 50 milli Amp secondary current and following way, self analysing auto c/k setting according to targeted power factor setting, the relay shall have minimum three digit display unit for display of real power factor, targeted power factor, lag/lead capacitor switching status, alarm output for under current, over current, insufficient compensation, indication of switching on units, auto/manual status, and shall have over load protection, no volt release etc. as required, 6 to 14 stage - sensitivity upto 50 milli Amp. Makes: L&T/Seimens/Epcos /Schneider/ ABB/Neptune-1no

Bus Bars:- Supply and fixing of Electrolytic grade aluminium bus bars by means of SMC / DMC type insulator, high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves Control wiring with suitable size of approved make FRLS PVC flexible copper wires, Earth Bus Bar, Door Loop earhtings, Ferrules, Feeder identifications, danger plate, door locks, auxilary contactors for auto manual operation and all other accessories including all labour charges etc with connections for finished item of work including transportation charges

Providing transformer plinth 1.2 x 1.2 x 1.5 mtr in size with necessary excavation in ground at the bottom with 150mm thick 1:2:4 cement concrete raft at the bottom and top and 225mm thick wall constructed in stone masonry and remaking hallow portion shall be filled with stone chips duly plastered 20mm thick outsides including watering etc., complete.

Supply and Transportation of 3C X 120 sq.mm XLPE insulated IS:7098/II/85 H.T.cable for working voltage 11 K.V Earthed with Stranded Compacted Circular Aluminium Conductor Screened with Extruded Semi-conducting compound, in combination with Copper Tape, cores laid up, inner sheath of Thermoplastic tape, galvanised flat steel strip armoured and overall extruded PVC type ST- 2 outer Sheathed cable etc complete Make: Torrent / Universal / Unicab / Havells / KEI /Polycab/ Gloster/RR Kabel/RPG

Supply and making heat shrinkable type outdoor termination kit of approved make suitable for XLPE insulated 11 KV cable, with required components, prepration of cable ends, testing etc as required of following sizes. Makes: Raychem /M seal/ Denson/ Multy/ Transeal- Hongshang Outdoor Termination Kit for 11KV XLPE (E) : 3 core 120/150/185 Sq mm

Supply and making heat shrinkable type indoor termination kit of approved make suitable for XLPE insulated 11 KV cable, with required components, prepration of cable ends, testing etc as required of following sizes. Makes: Raychem /M seal/ Denson/ Multy/ Transeal- Hongshang Indoor Termination Kit for 11KV XLPE (E) : 3 core120/150/185 Sq mm

Earth work excavation of Trench in hard ground soil, laying of U.G cables from 70 to 300 Sqmm on sand cushion covering the cable with bricks and back filling of trench cost and conveyance of materials and labour charges etc., complete.

Labour charges for run of U.G cables from 70 to 300 Sqmm on wall with necessary fixing arrangments such as saddles, clamps etc., as directed by department including cost and conveyance of all materials etc., complete.

Providing independent earthling by excavating a trench to a depth of 2.5 M in all soils, as per size specified in the Data, using 100mm dia Heavy gauge Flange C.I (Cast iron) pipe of 2.5 Mtrs length with necessary accessories duly providing staggered holes including filling with equal proportion of Salt and Charcoal in layers and all labour charges etc., complete.

Providing independent earthing for Sophisticated Electronic equipment with 600mm x 600mm x 3.15mm thick copper plate rigidly fixed to 40mm dia G.I Pipe of 2.5 mtr length connected with reducer providing G.I funnel with wiremesh as per National Electric Code including C.C.Chamber of size 400m x 400m x 400mm covered with R.C.C. Slab filling with salt and charcoal giving earth connection from electrode with Copper strip of 25mm x 5mm x 200mm length to be bolted with nut bolts to G.I.pipe including 25mm x 3mm copper strip of 6Mtrs length connected from plate to Copper strip with all accessories and labour charges complete as per IS specification 732/1982 (Part II).

Supply and Run of 50mm x 6mm G.I Strip including cost of all accessories and labour charges etc., complete

Supply and Run of 40mm x 6mm copper strip including cost of all accessories and labour charges etc., complete.

Earth work excavation for foundations (Manual Means) of buildings, septic tank, sump, compound wall in ordinary soils and depositing on bank with an initial lead of 10m and depth up to 3m including all operational,incidental, labour charges such as shoring, sheeting, planking, strutting etc., and overheads & contractors profit complete for finished item of work excluding dewatering charges etc., as per SS 20 B(APSS 308)

Plain Cement Concrete (1:5:10) (cement: fine aggregate: Coarse aggregate) for foundations and under flooring bed using coarse aggregate 40mm size hard , machine crushed granite from approved quarry using concrete Mixer 10 / 7 cft (0.2 / 0.8 cum) capacity including cost and conveyance of all materials like cement, sand, coarse aggregate, water etc. to site including all charges for machine mixing and hire charges of concrete mixer, laying concrete in foundations and under flooring bed, ramming in 15 cm layers finishing top surface to the required level curing etc.,and overheads & contractors profit complete for finished item of work. (APSS No. 402)

Masonry work in CM(1:6) prop (Cement : Sand) in superstructure with fly ash cement / lime solid blocks of size 290mm x 225mm x 140mm from approved source having minimum crushing strength of 50 Kg/Sqcm. including cost and conveyance of all materials like cement, sand, fly ash cement / lime solid blocks, water etc., to site, labour charges, like mixing cement mortar, scaffolding charges, constructing masonry, lift charges, curing, overheads and contrctor profit etc., complete for finished item of work. (APSS No. 501 & 504).

Supply and errecting fencing section having hot dipped galvanised Iron chain link mesh of 8 gauge (4.0 mm) as per IS: 2721-1979 at a spacing of 2"x2" (50 mm x 50 mm) and including all accessories and duly painted with one coat of red oxide and 2 coats of aluminium paint and all labour charges etc. complete.

Plastering 20mm thick single coat in CM(1:5) using screened sand including cost and conveyance of all materials like cement, sand, water etc., to site and all operational, incidental charges on materials and including cost of all labour charges for mixing mortar, finishing, curing as directed by Engineer-in-charge etc., and overheads & contractors profit complete for finished item of work for basement. (SS 901,903 & 904)

Supply, transportation and fixing of MS Angle Iron of size 50 x 50 x 6 mm for fixing as frame workincluding painting with red oxide paint and cost and conveyance of all materials and all labour charges etc complete.

Supply, transportation and spreading the 40mm size HBG metal in two layers of about 100mm thick in and around the sub-station yard.

Supply and transportation of following 300Sq mm X 3.5 core XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part-I)/1554-I Makes: Torent / Universal / Unicab / Havells / KEI / Gloster/Finecab / Polycab /RR Kabel/ Fortune Arrt

Earth work excavation of Trench in hard ground soil, laying of U.G cables from 70 to 300 Sqmm on sand cushion covering the cable with bricks and back filling of trench duly providing route indicator embedded in C.C including cost and conveyance of materials and labour charges etc., complete.

Labour charges for run of armoured U.G cables from 70 Sq.mm to 300 Sq.mm in existing cable trench/cable duct/ cable tray/hume pipe/G.I. pipe with necessary fixing arrangments such as cable ties etc., as directed by department at site.

Supply and making one end termination with heavy duty double compression brass gland as per BS 6121:2005 ,IP 66 complete,SIBG type, heavy duty Alluminium lugs duly crimped with crimping tool, PVC tape etc for following size of Armoured PVC insulated & PVC sheathed/ XLPE aluminium conductor cable of 1100 volt grade as required of size. Makes:Dowels/Comet/SMI 3.5 core x 300 sq.mm

Rupees Twenty Five Lakhs Fourty Two Thousand Six hundred and Eighty Three only