Military Engineer Services Tender
To inquire about any e-tender the Andaman & Nicobar Islands government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder one can find every eprocurement Punjab tender on BidAssist. BidAassist has collated each and every Eproc Andaman & Nicobar Island Tender on its website. Looking for Andaman & Nicobar Island tenders online or going through the cumbersome government websites for it, has been made easier with the help of BidAssist.
Military Engineer Services - MES Tender
Civil And Construction
Civil Works Others
Eprocure
Opening Date13 May 2023
Closing Date1 Jun 2023
Tender Amount₹ 48,00,000
Costs
EMD
₹ 96,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MES_595387_1Bid Award Id
ViewTender No
8752/GE/H/PBTender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Demolition of cement concrete un-reinforced in any position and paving not exc 15cm thick above or below ground level complete all as specified and as directed.
26.88
-
-
Demolition of Reinforced manhole , Drain over cover slabs in suimilar works etc complete all as specified
4.5
-
-
Supply & fabricate and fixing in position angle iron posts for fencing posts and struts including flat iron etc and including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets for securing fencing including all necessary welding , drilling, bolting or riveting, complete all as specified and directed.(Steel confirming to Fe-290 (Gde E-165)).
500
-
-
S&F for MS Galvanized with 1.0mm thick PVC coated chain link fencing 50mm x 50mm over 3.15mm GI wire all as specified
90
-
-
S & F for 10mm dia MS round bar for tighting/securing fencing wire etc,including two coats of synthetic enamel mpaint over a coat of red oxide
50
-
-
M & L for Mild steel screw bolts (machine made) with hexagonal or square head one end and screwed the other, or screwed both ends each screw-wed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long diameter of neck in exc 16mm and n.exc 20 mm
20
-
-
M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in cooping
1
-
-
M&L precast cement concrete block masonry exc. 10 cm width with solid block C1 (1:3:6) (using 20 mm graded stone aggregate) and setting in cement mortar (1:6) all as specified.
15
-
-
M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in cooping in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water roughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed
3
-
-
M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified & directed by Engineer-in-Charge.
3
-
-
M&L PCC (1:4:8) type D2 using 40mm graded stone aggregate as in 75mm thick as in sub base complete all as specified & directed by Engineer-in-Charge.
145
-
-
M& L for plain cement concrete type A-1 (1:1.5:3) (Using 20 mm graded stone aggregate) as in hard standing finished with even and smooth with using extra cement including use and waste form work complete all as specified and directed.
10
-
-
Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade `A'
4
-
-
Finishing surface to concrete roads, pavements, by brooming
9
-
-
S&F for glossy finished chequerred cement concrete tiles 30cmx30cmx25mm thick set jointed with grey cement and pigment and pointed in neat cement slurry including 20 mm thick screed bed of CM(1:6) in floors
125
-
-
M&L for machine pressed precast concrete interlocking paver block glossy finished of any shape and size with grey cement and pigment confirming to IS 15658-2006 of 80mm thickness, M-40 Grade laid dry to any pattern or profile as directed incl filing to the edges in CM 1:4 all manufacturer's instruction complete all as specified and directed
20
-
-
M&L for sand filling under floors or in foundation including watering and consolidation incl spreading and levelling
1
-
-
Excavating in post holes (or similar holes) each not exc 0.50 Cum, getting out hard/dense soil, returning filling in and ramming earth or Brocken rubble mixed with earth around, in layers not exceeding 25 cm
12
-
-
M&L for cement concrete Type B-1, 1:2:4 (using 20 mm graded stone aggregate) for post, struts (including caps) including weathering, slightly rounded or chamfered angles and throating and including necessary form work all as specified and directed
6
-
-
M&L for pre cast cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in manhole cover slab set in cm 1:6 all as specified and directed
4.5
-
-
M&L for cement concrete1:2:4 Type B-2 Using 20mm graded stone aggregate as in surface channels or drain
2
-
-
M&L for vitrified tiles light shade 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 15mm thick in cement mortar 1:4, complete all as specified.
20
-
-
Ditto all as per item No 03 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.
4
-
-
M&L for non skid ceramic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tiles exc 0.06 Sqm but n. exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed of CM (1:4) bedding complete all as specified
80
-
-
M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.
35
-
-
Ditto all as per item No 06 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.
7
-
-
M&L for non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.
50
-
-
Ditto all as per item No 08 above but as in skirting / dados etc. including backing coat 10mm thick in cement mortar 1:3, complete all as specified.
10
-
-
M&L for glazed ceramic designed coloured tiles as in vertical surfaces of size 300x450x7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match designed incl 10 mm thick backing coat in CM (1:3) complete all as specified.
80
-
-
M&L 16 to 18mm thick granite stone (of any type ) work (table rubbed and polished) in floors, staircase tread & risers of steps, cooking platform, window cill/jambs etc laid bedded over 15mm thick CM (1:4) bedding & pointed in white/coloured cement to match coloured tiles including Rounding, grinding and mirror polishing complete. (Note : Colour of granite shall be as approved by Engr-In-Charge)
30
-
-
Dismantling of ceiling boarding including grid of any description fixed in any position with nails
80
-
-
S&F for anodoised aluminium powder coated snap grid frame work for ceiling 605mm x 605mm using aluminium anodoised sections aluminium section main tee 36.5x25x1.4mm, cross 23.5x26.4x1.4mm, angle 25x25x1.4mm including cutting, drilling jointing etc complete including 4mm dia of GI hangers wire suspenders fixed with adjustable connectors and providing 6mm thick E-boards (Classic) 605mm x 605mm size Specified by Engr-in-charge and making good
55
-
-
M & L for seamless false ceiling made out of 12mm thick of gypsum board fixed to the ceiling section with 25mm long self drilling and tapping screws having Philips head with under head cutter at 200mm centre to centre, including finishing the joints of face board with specially formulated joining compound and 48 mm wide fibre tape to provide seam less finish and including GI channel 0.55 mm thick with two unequal flanges of 20 to 30mm and web of 27 mm fixed to surrounding wall using nylon sleeve and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 215 mm each and web of 45 mm suspended from soffits at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.20mtr length) of 0.55 mm thick having kurled web of 50 mm and flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 6mm thick GI hangers adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flats 40x3 mm size long and expansion hold fasteners 12.5mm dia 40mm long including thin layer of Pop with Gypsum binder, sanding the surfaces till smooth surface is obtained and finally applying two coats of acrylic emulsion over one coat primer over 3mm thick putty all as specified and as directed
25
-
-
Taking down chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each
6
-
-
Taking down chowkhats or frames with shutters without taking off shutters from frame n.exc 1.5 Sqm each
6
-
-
Taking down shutters of any description exc 1.0 sqm but n.exc 2.0 sqm each
6
-
-
Taking down Aluminium Windows chowkhats or frames with shutters without taking off shutters from frame exe 1.5 Sqm and n.exc 4 Sqm each
12
-
-
Taking down Aluminium Windows and Ventilator chowkhats or frames with shutters without taking off shutters from frame n. exe 1.5 Sqm each
10
-
-
S&F IInd class hardwood plain solid straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints.
0.22
-
-
S&F flush shutter 35mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick wooden lipping around the edges of shutter complete all as specified and directed.
12
-
-
S&F 35mm thick, IInd class hard wood glazed and skeleton shutter open rebated and prepared to receive gauze, etc. ( without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing gauze etc size of members of shutters as specified in as Part I Ses 8 Cl 8.24 (a)
10
-
-
S&F Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube, fixed in opening as per specification all as directed
50
-
-
S & F for Factory made solid PVC molded with particle board core door shutter 28 to 30 mm thick panel design with 2mm thick molded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing all as specified
25
-
-
S&F in butt hinges extruded aluminium alloy with galvanized mild steel hinge pin ,anodized of hinges 100 mm type B-21
66
-
-
S&F extruded aluminum alloy handle fabricated type anodized 150mm long.
44
-
-
S&F Aluminum anodized barrel bolt of extruded section 150mm long
44
-
-
S&F Aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing bolts and sliding bolts of extruded such or cast aluminum alloy
10
-
-
M&L for HDF boards (fire & water proof) of 19mm thick as in CB, cabinet, shelves etc & the like with an including 02 coats of synthetic enamel spray painting glossy finish over a coat of primer incl preparation of surface complete all as specified and as directed.
15
-
-
S&F auto hinges stainless steel grade AISI-316 (type Austenitic anticorrosive in nature) suitable for kitchen cabinets,CB , Shelves etc
30
-
-
S&F contineous (Piano) hinges mild steel bright finish or electrogalvanised, width of flaps 40 mm
12
-
-
S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge
300
-
-
S&F for providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene asket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, auminium snap beading for glazing/ paneling, C.P. brass/ tainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge
200
-
-
Supply only plain sheet glass 4.0 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum window shutter not exc 0.5 Sqm in each pane.
18
-
-
Supply only plain sheet glass 4.8 mm thick ordinary quality and glazing with aluminum glazing clip in aluminum Door shutter exc 0.5 Sqm in each pane.
12
-
-
Supply only figured glass, pin head type sheet glass 4.0 mm thick ordinary quality and glazing with aluminium glazing clip in aluminium window shutter not exc 0.5 Sqm in each pane.
7.5
-
-
S&F Prelaminated particle board 12 mm thick, exterior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work complete.
12
-
-
S&F floor door stopper of aluminium alloy body & tongue, anodised with hard drawn spring of 140mm size fixed in floor complete all as specified and directed
8
-
-
Supply only Aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.
12
-
-
Supply and fix in repairs aluminium alloy wire mesh 0.45 mm nominal dia of wire average width of aperture 1.40 mm and fixed with aluminum wire staples all as specified and directed.
50
-
-
S&F Powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.
60
-
-
S&F in repairs aluminum (extruded section) body, door closer hydraulically regulated designation No. 3, universal type, suitable for door shutters of 851 to1000 mm width and of weight between 61 to 80 Kg and fixed complete all as specified and directed.
6
-
-
Dismantling of cast iron/PVC pipe any dia and any shape incl bends/branch pieces jointed in cement mortar and taking out if reqd.
60
-
-
S&F for 110mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.
35
-
-
S&F for 110mm dia PVC (SWR) bends any radius complete all as specified.
10
-
-
S&F for 110mm dia PVC (SWR) bends with acess door any radius complete all as specified.
8
-
-
S&F for 110mm dia PVC (SWR) branch piece single (Single T ) equal or unequal complete all as specified.
6
-
-
S&F for 110mm dia PVC (SWR) vent cowl complete all as specified.
2
-
-
S&F for 75mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints fixed to wall etc using synthetic rubber adhesive cement solvent complete all as specified.
25
-
-
S&F for 75 mm dia PVC (SWR) grade bends of any radius
6
-
-
S&F for 75 mm dia PVC (SWR) grade bends with acess door of any radius
4
-
-
S&F for 75 mm PVC (SWR) branch piece, single (SingleT ) of radius equal or unequal complete all as specified.
4
-
-
S&F for 75 mm PVC (SWR) branch piece, single (Single Y) of radius equal or unequal complete all as specified .
4
-
-
S&F for 75 mm PVC (SWR) vent cowl complete all as specified.
2
-
-
M&L for 75 mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified.
6
-
-
S&F in repairs vitreous china ware wash hand basin white flat back of size 550x 400 mm with pedestal including brackets, 32 mm CP waste coupling, chain and plug, waste fittings, and all necessary inlet, out let connections complete.
7
-
-
S&F in repairs 15 mm bore pillar taps, cast copper alloy, chromium plated fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts(Make :Prayag Cat No. PIS-50H or Equivalent approved)
7
-
-
S&F in repairs for bib taps long body with flange cast copper alloy chromium plated fancy type with capstan head handle screwed down for Iron pipe or for brass fancy for CP brass fancy type 15mm dia(Make :Prayag Cat No. PIS-08H or Equivalent approved)
14
-
-
S&F in repairs two way bib cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank and cup (Make : Prayag Cart Part No PIS-12 H or Equivalent approved)
6
-
-
S&F in repairs angular stop cock cast copper alloy fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed for 15mm bore of pipe with long shank and cup (Make :Prayag Cat No. PIS-10 H or Equivalent approved)
12
-
-
S&F in repairs vitreous china ware wash down white water closet pan (pedestal pattern with trap incl connecting to drain and flushing pipe, antisyphonage pipe incl PVC sheet cover etc complete all as specified.
3
-
-
S&F in repairs vitreous China squatting pan, `Orissa' pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe)
2
-
-
S&F in repair PVC valveless syphonic action type flushing cistern 10 ltr capacity white with intel ball valve float flush pipe and handled including brackets complete all as specified.
10
-
-
S & F in repairs Brass chromium plated towel ring with round flange. (Make Prayag Cat Part No. BA-11 or Equivalent approved)
8
-
-
S&F in repairs Brass chromium plated tubular towel rail 20mm dia & 60 cm long between flange. (Make Prayag Cat Part No. BA-70 or Equivalent approved)
20
-
-
S&F in repairs Hand shower (health faucet) with 8mm dia & 1.0mtr long flexible tube with wall hook. (Make PrayagCat Part No. BEA-41 or Equivalent approved)
6
-
-
S&F in repairs PVC connection 15 mm dia and 600 mm long with both and nuts
12
-
-
S&F in repairs looking mirror 600 x 450 mm bevelled edge of selected quality glass, mounted on 6mm thk AC bldg board or commrcial ply wood & fixed to wooden plugs with chromium plated brass screws and cup washers complete.
8
-
-
S&F in repairs 1mm thick Stainless steel sinks with drainage board in kitchen with waste coupling, plugs, washers and waste pipe fixed on granite platform, over all size 915 X460mm bowl size 410mm X 330mm X 160mm complete all as specified.
2
-
-
Labour for drilling holes with drill machine with electric driven for gas pipe etc not exc 25 mm dia Upto 10cm depth in marble stone etc
2
-
-
S& F in repairs 20mm to 25 mm dia, Harrison rails, powder coated anodized aluminium alloy with fancy type fixing curtain brackets, stops, rollers etc
60
-
-
S&F in repairs for plate rack of stainless steel of size 31X36X10 (inch) with steel sleevs & hanging arrengement for utensile, complete all as specified and directed (Make : Prayag Cat No. P-348)
2
-
-
S & F in repairs for wall mixer 3-in-1 system with provision for both hand shower and over head shower composite with 115 mm long bend pipe connecting legs & wall flanges Mixer (Make: Prayag Cat No PIS-80H), hand shower including 1.5 mtr flexible tube with hook Cat No BHS-87, and over head showerwith arm and flange(300mm) of cat No BOS-90.
1
-
-
S&F in for Corner glass self assembly size 300mm with chromium plated bracket guard and railing (Make: Prayag Cat No. BEA-44)
6
-
-
S&F in repairs concealed stop Cock with wall flange incl all fittings complete all as specified and as directed.
Make : Prayag cat No-7318
3
-
-
S&F in repairs CP overhead shower dia 125 mm overhead shower round with revolving joints (with body rotation) & 225mm long arm shower with rabit cleaning system and all fittings Make - Prayag BS-76 as approved.
4
-
-
Taking up or down 20mm dia steel tubing connection, including cleaning for refixing or removal to store
30
-
-
Taking up or down 25mm dia steel tubing connection, including cleaning for refixing or removal to store
40
-
-
S&F 20 mm dia bore of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified
30
-
-
S&F 25 mm dia bore of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified
40
-
-
S&F in repairs for providing 25mm dia Gun Metal, globe or gate valves with iron wheel head, screwed both ends for iron pipes
5
-
-
Cutting chases in PCC block walls for concealed water tubing etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by engineer- in- charge.
10
-
-
S&F rotational moulded Polyethylene [HDPE] Water Tanks, Triple Layered, ISI Marked Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes including taking down old tanks complete all as specified and as directed by Engineer- in - charge.
3
-
-
S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe bore dia of 25mm (Minimum weight 455 gms) complete all as specified and as directed by Engineer- in - charge.
3
-
-
Dismantling plain or corrugated steel sheeting any gauge, thickness including similar pattern roof coverings.
295
-
-
S&F for pre painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering fixed with self tapping screws as specified.
270
-
-
S&F for pre painted Galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an coloure having tensile strength of 550Mpa as in roof covering, ridge, eves gutters etc fixed with self tapping screws as specified.
25
-
-
Dismantling structural steel work complete all as specified.
14
-
-
M&L for rolled section as in main and cross beam, hip and jack rafter,purline where connected to common rafters and running rails and guides for sliding doors fixed witg angle cleats or other connecting plates of grade Fe-410 (grde E-165)
450
-
-
M&L for aluminium wind tie of any size fixed with self tapping screws of size 50/75mm with integral EPDM washer in roof covering and including dismantling of old wind tile
124
-
-
S&F in repairs collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete
20
-
-
S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165
200
-
-
S&F in repairs for Framed work such as ornamental and intricate design Gate, grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165
865
-
-
M&L for preparation of new steel surfaces over 10 cm in width or girth not otherwise described and applying 2 coats of synthetic enamel paint over one coat of red oxide primer all as directed.
210
-
-
M&L for preparation of old steel surfaces over 10 cm in width or girth not otherwise described and applying one coats of synthetic enamel paint over one coat of red oxide primer all as directed.
40
-
-
M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia for securing with clips quality conforming to deformed or twisted bars.
450
-
-
S & F in repairs stainless steel tubing of any diameter of circular, square or rectangular in shape of grade AISI-316 (type Austenitic anticorrosive in nature) as in railings / grills / designer work including post top cap, bottom plate, cutting, bending, seamless welding and fixing in any type of location incl taking down old railing of any description complete all as specified and as directed.
110
-
-
Taking down cement plaster on brick /stone masonry / concrete surfaces of wall / ceiling incl raking out joints, hacking for key, scrubbing down with water etc and deposited the debris outside the MD land complete all as specified.
70
-
-
M&L for rendering 15mm thick in CM 1:4 including mixing water proofing compound on concrete/block masonry surfaces and finished even and smooth without using extra cement all as specified.
40
-
-
M&L for 10mm thick plaster in CM (1:6) on fair faces of concrete/PCC block surfaces of walls finished even and smooth (without using extra cement) all as specified.
260
-
-
M&L for broken stone or boulders hard core of gauge exc. 63 mm but not exc. 100 mm, deposited, spread and levelled in layers of not exc.15 cm thick, watered and rolled rammed to a true surface.
8
-
-
M&L for Forming fair finished drain using extra cement.
60
-
-
M&L for preparation on newly plastered wall surface and applying two coats of cement base paint complete all as specified and as directed.
100
-
-
M&L for preparation of old surfaces of walls and applying one coat of cement base paint including filling of cracks, holes and including leveling the surface which undulation found with cement putty etc. complete all as specified.
700
-
-
M&L for preparation of newly plastered wall surfaces and applying two coat of oil bound distemper over one coat of primer including leveling the surface which undulation found with cement putty etc complete all as specified and directed.
30
-
-
M&L for preparation on newly plastered external wall surface and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).
40
-
-
M&L for complete removal of existing treatment of old decorated external wall surface by scrapping, washing, cleaning etc and applying two coat of weather proof (exterior grade) acrylic emulsion paint with anti fungal property over a coat of primer of the same manufacturer as that of paint incl filling cracks, holes using wall care putty complete all as specified and as directed. (Make: Dulux Weather Shield Max or Apex Ultima from Asian Paints or Berger weather coat All guard).
550
-
-
M&L in repairs Aluminium composite panel sheet of 3.0mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwitched by 2.5mm polyethylene core with PVDF coating of 30.0 micron fixed over frame of aluminium tubular section 25x50mm.20.0mm thick, dully fixed to wall/ceiling with expansion fastner, having panels not exc 1200x1200mm with necessary silicon filling, in approved pattern as in column, beam, wall etc. compete as specified and as directedNote: Necessary MS scaffolding required for work shall be deemed to be included in the quoted rate.
50
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements