Military Engineer Services Tender
To inquire about any e-tender the Andaman & Nicobar Islands government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder one can find every eprocurement Punjab tender on BidAssist. BidAassist has collated each and every Eproc Andaman & Nicobar Island Tender on its website. Looking for Andaman & Nicobar Island tenders online or going through the cumbersome government websites for it, has been made easier with the help of BidAssist.
Military Engineer Services - MES Tender
Civil And Construction
Eprocure
Opening Date22 Oct 2024
Closing Date12 Nov 2024
Tender Amount₹ 43,50,000
Costs
EMD
₹ 87,000Document Cost
₹ 500Tender Fee
Refer Documents
Summary
Repair/ Maint Of Fire Fighting System, Pump Sets, Sprinkler System And Periodical Repairs/ Comprehensive Maint Of Lifts And Other Allied Works At Inhs Dhanvantari Bv Yard And Other Otm Area And Day To Day Complaints And Certain B/r Repair At Lltr Por
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_666889_2Tender No
8453/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
(iv) The above maintenance include complete maintenance of existing lift by regularly and systematically examining adjusting fabricating as and attending complaints/ break down calls within respective time frame as catered in Particular specification for smooth and efficient functioning of the equipment/lift (v) Contractor will prominently display his contact/ mobile number and OEM contact number inside and outside the lift on each lift for call in emergency.
(vi) Contractor shall submit safety security certificate of lifts from OEM in every month as per performa given in particular specification and shall be submitted along with running account receipts and final bill failing which payment shall not be processed.
(vii) Monthly maintenance check will be carried out by OEM as per monthly maintenance check list mentioned in particular specification.
-
-
-
S & F in repair of the following items for the service lift prior to AMC for lift No. L-H 5936 complete all as specified and as directed by Engineer-in-Charge:
(a) Charger Unit - 01 No
(b) Charger battery - 01 No
(c) Metal roller 'V' Assy - 08 Nos
(d) Bearing oil - 03 Ltrs
(e) Door belt (big) - 01 No
(f) Door belt (small) - 01 No
(g) Gong bell PCB Assy incl LED back light with coil (white), voice board ver V3 - 12-24 V DC - 04 Nos
1
-
-
S & F as in repair of the following items for the service lift prior to AMC for lift No. L-H 5937 complete all as specified and as directed by Engineer-in-Charge:
(a) Orange square dot matrix display with gong driver SG 1005 - 01 No
(b) Bearing Oil - 03 Ltrs
(c) Three way intercom (press & speak) handset - 01 No
(d) Gong bell PCB Assy incl LED back light with coil (white), voice board ver V3 - 12-24 V DC - 02 Nos.
1
-
-
S & F in repair of the following items for the service lift prior to AMC for lift No. L-H 5938 complete all as specified and as directed by Engineer-in-Charge:
(a) Charger battery - 01 No
(b) Bearing oil - 3 Ltrs
(c) Door belt (big) - 01 No
(d) Door belt (small) - 01 No
1
-
-
Supply,fixing,testing and commissioning of maintenance free battery 12V 18 AH including terminal clamps, copper lead of suitable length including disconnecting and removing existing unserviceable battery complete all as specified and as directed by Engineer-in-Charge
4
-
-
Supply & lay in repair water proof elevator floor mat made up of rubber with coin floor texture / anti skid texture for non slip floor having minimum thickness not less than 3mm complete all as specified and as directed by Engineer-in-Charge.
6
-
-
M & L for painting of one coat of synthetic enamel paint for the lift equipment i. e. motor, gear box, control panel, supporting structure etc including preparation of surfaces, writing of MES number complete all as specified and as directed by Engineer-in-Charge
3
-
-
M&L for servicing of 5 Ton capacity Manual operated crane installed at Main Power house, greasing, oiling, complete overhauling including testing all as specified and as directed by Engineer-in-Charge.
Note:(i) The quoted rate inclusive of all consumables and minor parts (ii)Chain pulley shall be measured and paid seperately under relevant item as supply only.
1
-
-
Supply only 05 Ton heavy duty chain pulley with lifting height minimum 6 m complete all as specified complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M & L for cleaning of semi underground static water tank of capacity 1.65 lakh litre by step by step procedure enumerated below :-
(a) The inner surface of the walls of the tank shall be cleaned with wire brush after emptying the water in the tank to adjacent tank.
(b) After thorough cleaning of the tank, the cleaning water and sludge is to be removed by using pump and the sludge has to be disposed off at a place as directed by Engineer-in-Charge.
(c) After removing the sludge from tank the tank shall be cleaned with anti bacterial agents.
(d) Applying water proofing compound to arrest leakages and seal the cracks on walls.
(e) After complete treatment, writing of "Tank capacity" 'Date of cleaning and due date of cleaning' on wall including applying two coats of white washing to external surfaces complete all as specified and as directed by Engineer-in-Charge
1
-
-
All as per item No 11.00 here in before but of semi underground sump capacity 60000 Liters complete all as specified and as directed by Engineer-in-Charge.
2
-
-
M&L for Inspection, maintenance and servicing of (60-105) HP Deisel Engine pump for 'B' check once in a 03 month or 250 hrs whichever is earlier of the engine for smooth functioning and carrying out the complete checks as per the manufacturers instructions all as specified and directed by the Engineer-in-Charge:-
(a) Replace the lubricating oil.
(b) Replace lubricating oil filter element.
(c) Replace lubricating oil by pass filter element.
(d) Replace the fuel filter element.
(e) Check engine coolent.
(f) Check the crank case breather.
(g) Check turbo charger (for turbo fitted engine).
(h) Draining out unserviceable engine oil from sump.
(i) Checking & adjusting fan belts.
Note. replacement of engine oil & radiator coolant shall deemed to be included in the rate quoted.
6
-
-
M & L for dismantling the pump of capacity 60HP- 40HP, isolating suction / delivery line connections, checking the worn out parts like impeller, shaft, stuffing box, shaft sleeve using Micrometer and transporting to workshop for repairs, check for condition of bearings, removing scales from impeller and pump housing, building the worn out metal of transmission shaft to required level, machining to the required size on lathe machine, grinding and finishing to match the sleeve, and fixing into the housing, re-assembling, transport back to the installation, installing in position, check for alignment with dial gauge, inserting shims where necessary, refixing with coupling, tightening with torque wrench to required level, re-connecting the flanged pipe connections of suction/ delivery, greasing for bearings including replacement of rubber insertion etc complete all as specified and as directed by Engineer-in-Charge.
Note :- Spares will be measured and paid separately under relevant schedule.
1
-
-
All as per item No 14.00 here in before but 12.5 HP / 10 HP complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only incorporating of pump set repair work for pumpset of capacity 60 HP - 40 HP :-
-
-
-
Shaft bushes with check nuts (stainless steel) for above pumpset.
1
-
-
Ball bearings suitable for above pump.
2
-
-
Metal Coupling for above pumpset.
1
-
-
Gland packing end cover (Stainless steel of suitable grade) as per existing size
1
-
-
Supply only for incorporating of pumpset repair work for pumpset of capacity 12.5 HP / 10 HP :-
-
-
-
Shaft bushes with check nuts (stainless steel) for above pumpset.
1
-
-
Ball bearings suitable for above pump.
2
-
-
Metal Coupling for above pumpset.
1
-
-
Gland packing end cover (Stainless steel of suitable grade) as per existing size
1
-
-
M & L for dismantling the defective induction motor of 60 HP - 40 HP capacity/make/class of insulation from foundation bed, disconnecting all electric supply connections, duly coupled with pump/compressor, trasnporting to workshop removing burnt out widing from stator/rotor, rewinding with suitable gauge of super enamelled copper wire of approved make and replacing/ refixing DE /NDE bearings, insulation materials, varnishing , heating, greasing of bearings etc complete, re-assembling, testing and commissioning of following capacity motors complete all as specified and as directed by Engineer-in-Charge. Note : Terminal block, Bearings of motor if required shall be measured & paid separately under relevant schedule items.
60
-
-
All as per item No 18.00 here in before but 12.5 HP / 10 HP complete all as specified and as directed by Engineer-in-Charge.
12.5
-
-
M & L for dismantling of motor of 60 HP - 40 HP capacities pumpset from installed position after disconnecting the coupling and electric connections and transporting the motor to the work shop, strip opening of the motor complete incl dismanlting stator, rotor assembly and cleaning the complete assemblies by taking out perished glass sleeve of connecting leads from common termination to terminal block, and washing with carbon tetra chloride, decarbonising and cleaning the rotor with CTC solution. Replacing the glass sleeve of connecting leads from common termination to terminal block, binding the loose coils with binding cloth, varnishing the coils complete and applyng bectol on the excitor coils, stator coils and heating complete, reassembling the unit and testing with megger for insualtion value and re-assembling, aligning with pump, re-inserting shims where necessary, refixing with coupling, tightening with torque wrench to required level, re-connecting the electric cable etc check for drawing current testing, commissioning etc all as directed Engineer-in-Charge. Note: Bearings of motor if required shall be measured & paid separately under relevant schedule items.
1
-
-
All as per item No 20.00 here in before but 12.5 HP / 10 HP complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M & L for renewal of rubber bush coupling for the following capacities of pumpsets complete all as specified and as directed by Engineer-in-Charge.
-
-
-
60 HP to 40 HP
1
-
-
12.5 HP / 10 HP
1
-
-
Supply only following bearings required during rewinding / varnishing of motors complete all as specified and as directed by Engineer-in-Charge.
-
-
-
DE/NDE bearings suitable for 40 to 60 HP motor
2
-
-
DE/NDE bearings suitable for 12.5 / 10 HP motor.
2
-
-
Supply only terminal block complete with hardware of following capacity motors complete all as specified and as directed by Engineer-in-Charge.
-
-
-
60 HP to 40 HP
1
-
-
12.5 HP / 10 HP
1
-
-
Taking down unserviceable pressure guage of any size complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Supply and fixing of pressure gauge 0-21 kg/cm² ,4" dia complete with necessary fittings complete all as specified and as directed by Engineer-in-Charge.
4
-
-
S&F in repair fully automatic starter delta startor 3 Phase 415 Volt 50 HZ suitable for 60 HP capacity induction motor complete all as specified and as directed by Engineer-in-Charge.
1
-
-
S&F in repair DOL starter three phase, 415 Volt with over load relay suitable for 10/12.5 HP capacity with sheet steel enclosure complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M&L for preparation/cleaning of outer surface by scrapping with emery paper or other means and painting of fire fighting pump motor of capacity 60 HP with two coat of synthetic enamel paint of red colour complete all as specified and as directed by Engineer-in-Charge.
1
-
-
All as per item No 29 .00 here in before but 40 HP complete all as specified and as directed by Engineer-in-Charge.
1
-
-
All as per item No 29.00 here in before but 12.5 HP / 10 HP complete all as specified and as directed by Engineer-in-Charge.
2
-
-
M& L for preparation to external old steel surface of fire fighting pipe line/hose box/door/panel board and connected accessories of various sizes by scraping and applying a coat of synthetic enamal paint complete all as specified and as directed by Engineer-in-Charge.
Note :- (i) Colour of paint will be decided by Engr-in-Charge.
(ii) Scaffolding and other safety precution equipment will be arranged by the contractor for the pipes which are upto G+3 floor height and cost for the same shall be deemed to be included in the quoted rate.
(iii) Contractor shall made good all disturbed surfaces and quoted rate deemed to be inclusive for the same.
165
-
-
Taking down old unserviceable MS pipe of any class and any size complete all as specified and as directed by Engineer-in-Charge.
60
-
-
Supply and lay MS pipe ERW Heavy (IS1239) erect, jointing complete of 150 mm dia with necessary supports and specials such as tees, bends, reducers etc including consumables and painting with one coat of red oxide primer and two coat of synthetic enamel paint including making good the disturbed surfaces of wall/ ceiling etc complete all as specified and as directed by Engineer-in-Charge.
6
-
-
All as per item No 34 here-in-before but of 100 mm dia complete all as specified and as directed by Engineer-in-Charge.
6
-
-
All as per item No 34 here-in-before but of 80 mm dia complete all as specified and as directed by Engineer-in-Charge.
18
-
-
All as per item No 34 here-in-before but of 50 mm dia complete all as specified and as directed by Engineer-in-Charge.
12
-
-
All as per item No 34 here-in-before but of 25 mm dia complete all as specified and as directed by Engineer-in-Charge.
Notes for item Nos. 34 to 38:-
(i) The excavation earth work measured and paid seperately under relevant item.
(ii) Flanges & gaskets at both ends of each pipe shall be included in the quoted rate.
(iii) The quoted rates also include for cutting of existing pipe for insertion of
fittings / new branch pipe.
(iv) Painting to the new pipe including applying primer shall be measured and paid seperately.
18
-
-
M& L for preparation to external new steel surface of fire fighting pipe line/hose box/door/panel board and connected accessories of various sizes by scraping/ preparation of surfaces and applying two coats of synthetic enamal paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.
Note :- (i) Colour of paint will be decided by Engr-in-Charge.
(ii) Scaffolding and other safety precution equipment will be arranged by the contractor for the pipes which are upto G+3 floor height and cost for the same shall be deemed to be included in the quoted rate
(iii) Contractor shall made good all disturbed surfaces and quoted rate deemed to be inclusive for the same.
100
-
-
S&F in replacement Sprinkler glass bulb type (Standard response) as per IS:15106/TAC guidelines 68 degree temperature rating pendent type complete all as specified and directed by Engineer-in-Charge.
19
-
-
S&F in repair Addressable manual call point resettable type complete all as specified and as directed by Engineer-in-Charge.
4
-
-
S&F in repair Fire Alarm Sounder cum strobe shall have audibility level not less than 85 DB measured at 1m, strobe shall have not less than 75 cd flashing at 1 Hz for visual indication with control module, operating voltage 24 volts DC the sounder cum strobe shall be integrated with control modules of existing FACP complete all as specified and as directed by Engineer-in-Charge.
1
-
-
S&F in replacement butterfly valve with CI body of size 100 mm dia with suitable gasket, nut & bolts including necessary welding works as required complete all as specified and as directed by Engineer-in-Charge.
1
-
-
S&F in replacement butterfly valve with CI body of size 150 mm dia with suitable gaskit, nut & bolts including necessary welding works as required complete all as specified and as directed by Engineer-in-Charge.
1
-
-
S&F in replacement butterfly valve with CI body of size 80 mm dia with suitable gaskit, nut & bolts including necessary welding works as required complete all as specified and as directed by Engineer-in-Charge.
2
-
-
S&F in replacement ball valve of size 25 mm dia with necessary welding works as required complete all as specified and as directed by Engineer-in-Charge.
2
-
-
S&F in replacement cast Iron Non return valve, short body type, flanged ends heavy duty as per IS 5312, PN 1.6 of size 150 mm dia including 6mm thick rubber insertion ring complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M & L in replacement for yard hydrant post 80 mm dia MS of flange type complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M & L for servicing of 26 No fire hydrant posts for arresting any leakage, replacing damaged O rings, lock plugs, end caps with chain complete all as specified and as directed by Engineer-in-Charge.
Note: (i) lock plugs shall be measured and paid seperately under relevant item as supply only.
1
-
-
Supply only lock plugs for fire hydrant posts complete all as specified and as directed by Engineer-in-Charge.
4
-
-
M & L for servicing, maintenance, repair & attending break down calls of M/s Edwards make fire alarm panel along with all connected items (control module/ monitor module/ smoke detectors/ isolators/ manual call points/ response indicators etc) connected through wires / comminication cables as per OEM instructions which includes preventive maintenance schedule of fire alarm panel and connected items, cleaning of panel and all connected items, checking the functionality of all modules, checking for any malfunction of the system and rectifying the same, replacing any damaged wire / comminication cable upto 30 mtr length, checking for receiving the notofications properly and if not rectifying the same and changing the mapping location with the item as per site requirement complete all as specified and as directed by Engineer-in-Charge.
Note:
(a) The rep of OEM shall visit the installation site for periodic preventive maintenance check up of fire alarm system for every 3 months other than breakdown job.
(b) Apart from the periodic preventive maintenance visits, all break down calls shall be measured seperately.
3
-
-
(c) The quoted rate is inclusive of minor parts only and all major parts like control module, monitor module, power supply board and mother board shall be measured and paid seperately under supply item only.
(d) In addition to the above the contractor shall deploy rep of OEM to rectify any type of defects arised during the contract period, to keep the fire alarm system in operational condition.
-
-
-
Supply only control module suitable for the existing fire alarm panel complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only monitor module suitable for the existing fire alarm panel complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only power supply control board suitable for the existing fire alarm panel complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only mother board suitable for existing fire alarm panel complete all a s specified and as directed by Engineer-in-Charge.
1
-
-
Supply and fixing in replacment fire hydrant valve, single headed including required washer and fittings complete all as specified and directed by Engineer-in-Charge.
1
-
-
Supply and fixing in replacment fire hydrant valve, double headed including required washer and fittings complete all as specified and directed by Engineer-in-Charge..
1
-
-
Supply and fix in repair C P Hose of 15 m length complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply and fix in replacement branch pipe gun metal 63 mm inlet made threaded outlet 15 mm bore nozzle short complete all as specified and as directed by Engineer-in-Charge.
2
-
-
M & L in replacment hose box made of 18 gauge MS sheet 800x600x250mm with double door with 4mm thick glass and door frame made of 16 gauge MS sheet painted fire red outside and brilliant white inside yard complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply and fix in replacment Hose reel Drum of 30 m long and 20 mm dia high pressure hose reel complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply and fix as in repair of transparent acrylic sheet thickness of minimum 3 mm for hose box complete all as specified and as directed by Engineer-in-Charge.
2.8
-
-
Excavation in trenches of soft/loose soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for foundation, pipe, laying of cable etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out complete all as specified and as directed by Engineer-in-Charge
4.86
-
-
Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil all as specified and as directed by Engineer-in-Charge by Engineer-in -charge.
4.28
-
-
Removing excavated materials (soil) to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 meter above the starting point all as specified and as directed by Engineer-in-Charge by Engineer-in -charge.
0.58
-
-
M & L for Cutting the tarmac / hard standings and excavating in trenches across the road for laying pipe including making good the excavated portion by means of readymix cold mix bitumen road repair mix matching with the existing road surface complete all as specified and as directed by Engineer-in-Charge
1.62
-
-
Demolition of brick work or stone boulder masonry, built in cement mortar complete all as specified and as directed by Engineer-in-Charge.
0.8
-
-
M&L for precast cement concrete solid block masonry exc 10cm in width type C1, 1:3:6 (using 20mm stone aggregate ) set in CM (1:6) for value pit chember etc.
0.8
-
-
Demolition of cement concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-Charge
0.75
-
-
M&L for Plain Cement Concrete in foundations, filling and mass concrete type D2 1:4:8 nominal mix ( 40 mm graded aggregate) including formwork complete all as specified and as directed by Engineer-in-Charge
0.75
-
-
M & L for carrying out repair, maintenanace, servicing and attending breakdown of oil fired incinerator of Make HATT, including inspecting all parts, control circuit wiring and control circuit boards / mother board for general repairs / servicing / over hauling as per OEM instructions for ensuring smooth and trouble free operation of equipment to the entire satisfaction of user / department all as specified and as directed by Engineer-in-Charge.
2
-
-
(a) The rep of OEM shall visit the installation site for periodic preventive maintenance check up of the Fire incinerator system for every 6 months other than breakdown job . During the process, the system shall be cleaned and general performance will be checked including inspection of all spare parts such as fuel injection pump, primary burner system, secondary burner system, operation of hydraulic doors, ID fan, FD fan, entire control circuit wiring, PCB board / control circuit board and all other connected items for functioning of the fire incinerator and repairing the same if found defective and testing & commissioning after rectifying defect complete all as specified and as directed by Engineer-in-Charge.
Note:
(i) All spare parts such as nozzle assembly, photo cell light detector, fuel pump, solenoid switch, ignition electrode, thermocouple, control circuit borad / mother board / PCB, burners, hydraulic oil shall be measured and paid seperately. (ii) The quoted rate inclusive of cleaning of Fire incinerator and connected system as per OEM instructions.
(iii) The charges for fixing, commissioning, testing of new spares including diamantling old units is included in the quoted rate.(Each job per incinerator is for 06 months and breakdown call will be measured and paid seperately).
-
-
-
Supply only following spares for carrying out repairs / maintenance / servicing / attending breakdowns under item No 71
-
-
-
Nozzle assembly
1
-
-
Photocell Light detector
1
-
-
Control circuit board / mother board
1
-
-
Hydraulic oil
50
-
-
Fuel pump BFP 41L3
1
-
-
Solenoid switch
1
-
-
Ignition electrode
1
-
-
Thermo Couple .
1
-
-
M&L in repair of inside fire chamber with fire bricks and gypsum of side wall and roof of the primary and secondary chamber including testing and commissioning complete as as specified and directed by Engineer-in-Charge.
1
-
-
M&L for cleaning of chimney of incinerator from chamber to upto 10 m height and removing all dirt, particles from inside and refixing with gland, nuts and bolts and cleaning of mild steel water tank, removing all particles from tank, replacement of GI Pipe connected from chimeny to water pump including valves and arresting any leakage in water collection tank and other accessories complete all as specified and as directed by Engineer-in-Charge.
1
-
-
M & L for carrying out repair, maintenanace, servicing and attending breakdown calls of chemical desiccant dehumidifier of capacity 600 cmh (FFB - 600), including strip opening of dehumidifier inspecting parts / spares for general repairs / servicing / over hauling as per the following scope of work given below for ensuring smooth and trouble free operation of equipment to the entire satisfaction of user / department all as specified and as directed by Engineer-in-Charge:
10
-
-
Scope of work:
(i) Filters: Check for physical status of filters, cleaning the both process and reactivation air filters by racking out filters from dehumidifiers and clean both the filters with compressed air or wash with warm soap solution and refix both the filters in their location. If the filters are damaged replace the filters of OEM recommended make.
(ii) Desiccant Rotor: Check the desiccant rotor for smooth operation, no sign of discoloration, pits, cracks due to dirt, dust or other foreign material. The desiccant rotor should be removed for cleaning from its position safely as per OEM instaructions. Cleaning the rotor by dry vaccum and dusting brush with attachment with soft bristle brush and vaccum both the surfaces of rotor or by applying moisture free compressed air of pressure rating less than 2 Kg/sqcm on one side at lease 250mm away from rotor surface and vaccum on other side, refix the rotor in its original position. The cleaning of desiccant rotor is upto full satisfaction of Engineer in charge and if the rotor replacement is inevetable due to poor performance of rotor the same should be replaced with new desiccant rotor of OEM make complete all as directed by Engineer-in-Charge.
-
-
-
(iii) Seals: Check the seals for any wear and tear and air leakge, the same should be replaced with high performing silicone seals complete all as directed by Engineer-in-Charge.
(iv) Reactivation air heater: Check the heater element complete all as directed by Engineer-in-Charge.
(v) Fan Motors: Check for any abnormal sound from the motors and clean both the process and reactive motors by removing from their original postion, remove the impeller and clean the fan impeller throughly and refix the same in original location.
(vi) Bed drive unit: Disconnect the bed drive motor supply check for any wear and tear of bed drive timing belt and replace the same if damaged and care should be taken for to avoid revese rotation of motor while refixing.
(vii) Electric circuit: Tighten all connections by applying proper torque .
-
-
-
(viii) Attending complaints of Dehumidifier of following capacity, checking for control circuit and power circuit connections from MCB TPN / SPN plug socket control point to dehumidier, healthiness of process fan & react fan motor winding, functionality of the contactors, over load relay, differential pressure switch, delay timer, heater coil, thermostat, limit switches, illuminating switches, rotation of dessicant rotor / bed drive reduction unit, complete as per nature of complaint and rectify the defect by replacing concerned material / rewinding of fan motors complete to make the dehumidifier operational all as specified and as directed by Engineer-in-Charge. Note:
(i) The quoted rate is inclusive of control wiring. (ii) Each complaint / servicing attended shall be measured as one job through job card.
(iii) All spare parts incorporated should be as per OEM recommendation only.
(iv) Sapres like control wiring, nuts / bolts / washers etc, T&P for servicing are deemed to be included in the quoted rate.
(v) Replacement of spares such as filters, desiccant rotor, bed drive unit, Bed drive timing belt limit switch, thermostat, seal group, heater coil, LED lamp, switches, contactors, relays, MCBs, rewinding of fan motor will be measured and paid separately under relevant items.
-
-
-
(vi) It is responsibility of contractor to engage required manpower as per requirement and take necessary measures to run the equipment in the event of breakdown to the satisfaction of user and as directed by Engineer-in-Charge. Considering the sensitive nature of installation the contractor shall always be in a position to make alternate standby arrangement in case of break down. Contractor shall keep his spares ready in advance for carrying out repairs without any delay. Any break down shall be attended within 2 Hrs and defects shall be rectified within 24 Hrs of time otherwise a recovery of Rs 2000/Hr along with cost of perished storage products due to non-functional of equipment shall be attributed to contractor without any further claim. The cost for same is deemed to be included in scope of item. The labour charges for fixing, commissioning, testing of new spares including diamantling old units is included in the quoted rate.(Each job per each dehumidifier unit for 04 months and breakdown call will be measured and paid seperately).
-
-
-
Supply only following spares for carrying out repairs / maintenance / servicing under item No 75
-
-
-
Supply only react air filter of size 280 x 160 x 25 mm for FFB 600 model complete all as specified and as directed by Engineer-in-Charge.
3
-
-
Supply only process air filter of size 350 x 160 x 38 mm for FFB 600 model complete all as specified and as directed by Engineer-in-Charge.
3
-
-
Supply only Desiccant rotor of OEM make for FFB 600 model complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only seal group of OEM make for FFB 600 model complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Supply only bed drive timing belt of OEM make for FFB 600 model complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only MCB TPN, 415 Volts, 32 Amps 10 KA complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Supply only power contactor 3 phase, operated by 230 volts complete all as specified and as directed by Engineer-in-Charge.
2
-
-
supply only Thermal overload relay complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only differential pressure switch complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only delay timer 0-10 (s/m/h) range complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only heater coil 2.4 KW,230 Volts AC tubular type complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Supply only thermostat of range 50-300º C complete all as specified and as directed by Engineer-in-Charge.
4
-
-
Supply only bed failure limit switch SPDT complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only illuminating switch complete all as specified and as directed by Engineer-in-Charge.
3
-
-
Supply only bed drive reduction unit with gear motor of capacity 0.34 HP, 230 volts complete all as specified and as directed by Engineer-in-Charge.
1
-
-
Rewinding of process / React fan motors of capacity 0.5 HP, 3 phase 415 volts complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Supply only MCB SPN 230 Volts, 25/32 Amps 10 KA complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Taking down MCCB of any type and any size complete all as specified and as directed by Engineer-in-Charge.
3
-
-
S&F MCCB 3 Pole 250 A, 25 KA breaking capacity, thermal magnetic release complete all as specified and as directed by Engineer-in-Charge.
1
-
-
S&F MCCB 3 Pole 100 A, 16 KA breaking capacity, therma; magnetic release complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Taking down MCB of any type and any size complete all as specified and as directed by Engineer-in-Charge.
3
-
-
S&F MCB TPN 40-63 A, 10 KA breaking capacity complete all as specified and as directed by Engineer-in-Charge.
3
-
-
Supply,fixing ,testing and commissioning of maintenance free battery 12V 180 AH including terminal clamps, copper lead of suitable length including disconnecting and removing existing unserviceable battery complete all as specified and as directed by Engineer-in-Charge.
2
-
-
Taking up or down old/chocked water tubings 15mm bore with fittings from trenches /walls and stacking at site including cleaning for refixing in new or old position or credit to contractor complete all as specified and as directed by Engineer in charge
6
-
-
Taking up or down old/chocked water tubings 20 mm bore with fittings from trenches /walls and stacking at site including cleaning for refixing in new or old position or credit to contractor complete all as specified and as directed by Engineer in charge
12
-
-
Taking up or down old/chocked water tubings 25mm or 32 mm bore with fittings from trenches /walls and stacking at site including cleaning for refixing in new or old position or credit to contractor complete all as specified and as directed by Engineer in charge
12
-
-
S&F 15 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and as directed by Engineer in charge
6
-
-
S&F 20 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and as directed by Engineer in charge
12
-
-
S&F 25 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and as directed by Engineer in charge
6
-
-
S&F 32 mm outer dia CPVC pipes of pressure rating 10kgf/cm2 fixed complete to walls ,ceiling s or in floors etc complete all as specified and as directed by Engineer in charge
6
-
-
M&L for cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing etc., and making good, cutting not ecx 10 cm girth complete all as specified and as directed by Engineer in charge
6
-
-
S&F in repairs 32mm waste fittings, brass, chromium plated for glazed ware sinks and basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repairs 40mm waste fittings, brass, chromium plated for glazed ware sinks and basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end complete all as specified and as directed by Engineer in charge
2
-
-
Fixing only in repairs bib cock including cleaning, removing of air block etc of any type and size complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs vitreous china wash basin, white flat back of size 550mm x400mm, excluding tap incl bracket complete all as specified and as directed by Engineer in charge
2
-
-
S&F in repairs bib tap cast copper alloy fancy type chromium plated screwed for 15mm bore complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repairs vitreous china wash basin, white flat back of size(mm) 600x480x195 incl all fixing accessories complete all as specified and as directed by Engineer in charge
2
-
-
S&F in repairs ball brass valve high pressure of polethene float and fly nut complete screwed for iron pipe and fixed, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed of 25mm bore complete all as specified and as directed by Engineer in charge
5
-
-
All as per item no.97.00 here in before but 20mm dia bore complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repairs (Non fancy type )Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed ends for pipe or union fixed for 15mm/20mm bore) complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs( fancy type ) Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm/20mm bore) complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs stop valves cast copper alloy chromium plated with long shank and cup (concealed type) fancy type screwed down high pressure screwed both ends for pipe or union fixed for 15mm bore,including necessary cutting and making good wall or floor tiling to match existing(tiles to be paid supplied only rates) complete all as specified and as directed by Engineer in charge
15
-
-
Fixing only in repairs stop cock (Non fancy type )size after cleaning and removing of blockage complete all as specified and as directed by Engineer in charge
10
-
-
Fixing only in repairs stop cock (Fancy type ) and size after cleaning and removing of blockage complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs vitreous china squatting pattern (IWC) of pattern long pan of size 580mm, white with P or S trap, front or back inlet and foot rest complete including provision of PCC (1:5:10) bedding complete all as specified and as directed by Engineer in charge
2
-
-
Fixing only in repairs by replacing minor parts like flushing knob, float, screws etc of PVC flush tank low level cistern, 10 ltr capacity, including connecting to existing water supply line and water closet pan complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs PVC flexible connection, of 15mm and 450mm long with brass unions and rubber washers on either side, for connecting water supply line to WHB, flushtank etc, complete all as specified and as directed by Engineer in charge
15
-
-
S&F in repairs Towel Holder Twin Type CP Brass complete all as specified and as directed by Engineer in charge
2
-
-
S&F in repair brass chromium plated over head shower rose with arm 125 mm size with long body with swivel joint including fixing to steel pipe or union, complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repairs sheet glass 5.5 mm ordinary quality and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and as directed by Engineer in charge
25
-
-
S&F in repairs PVC flush tank low level cistern, 10 ltr capacity, including connecting to existing water supply line and water closet pan complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repair 100 mm dia CP grating incl joints with solvent cement complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs vitreous china wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified and as directed by Engineer in charge
2
-
-
S&F in repairs vitreous china wash down water closet pan pedastel pattern of size 770x380x660 (EWC)(couple Closet) white in colour with and incl Soft close Seat cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified and as directed by Engineer in charge
2
-
-
Fixing only in repairs concealed stop cock of any type and size after cleaning and removing of washer of blockage complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs stainless steel sink with drainage board made out of 1.00 mm thick sheet with plug, washers, Ms angle cantilever brackets for suitable size and connecting union to pipe of overall size 1140 mm x 500 mm and bowl size 510mm x 400 mm x 190 mm complete all as specified and as directed by Engineer in charge
2
-
-
S&F in repairs PVC seat cover white closed pattern for EWC in repairs complete all as specified and as directed by Engineer in charge
5
-
-
S&F in repairs 600mm x 450mm mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood fixed to wooden plugs with chromium plate brass screws and cup washers complete all as specified and as directed by Engineer in charge
10
-
-
S&F in repairs tubular towel rail of 20mm dia of 60cm in length, D shaped bracket brass chromium plated including brackets complete all as specified and as directed by Engineer in charge
5
-
-
Taking down existing chowkats or frames n.exc. 1.5 Sqm each but with shutters (without taking off shutters from the frames removing to from store or handed over to contractor complete all as specified and as directed by Engineer in charge
5
-
-
Taking down existing chowkats exc. 1.5 Sqm and n.exc. 4 Sqm each without taking off shutter from the frame complete all as specified and as directed by Engineer in charge
5
-
-
Taking down shutters resecuring and easing of any description exc. 1 Sqm and n.exc. 2.00 Sqm each and refixing the same opening
5
-
-
S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed by Engineer in charge
25
-
-
S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and as directed by Engineer in charge
6
-
-
S&F plain, solid, straight chowkats and frames of 2nd class hard wood, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and as directed by Engineer in charge
0.15
-
-
S&F Glazed and skelton shutters 30mm thick of 2nd class hard wood open rebated and prepared to receive glass, gauge etc. edges of framing plain chamfered or rounded fitted without and mitred beads for securing glass etc., divided into squares sizes of members of shutters as specified in SSR Part-I, section 8Clause 8.20(a) with sash bars any numbers complete all as specified and as directed by Engineer in charge
10
-
-
S&F Plain framed panelled shutters (any number of panels), 35mm thick of 2nd class hard wood with panels of plywood flats complete all as specified and as directed by Engineer in charge
10
-
-
Demolition of tiles of any description or thickness in floor, hearth or wall including cement mortar bedding, removing debries off the premises complete all as specified and as directed by Engineer in charge
102
-
-
M&L for non-skid ceramic coloured tiles 7 to 8mm thick(square/rectangular)area of each tile exceding 0.06 Sqm but not exceeding 0.11sqm ,in floors etcset and jointed in cement slurry and pointed in coloured cement to match over a screed bed of 15mm thick in CM 1:4 complete all as specified and as directed by Engineer in charge
60
-
-
All as per Item No.128.00 here in before but for vertical surfaces such as skirtings, dados and risers to steps complete all as specified and as directed by Engineer in charge
10
-
-
M&L for 20 mm thick granite (of any type ) work (table rubbed mirror polished) edges rounded chamfered and bull nosed in steps, joints, cills, cooking platform & likes over screed bed incl pointing in white cement with admixture of pigment to match with shade of granite stone incl grinding and polishing complete all as specified and as directed by Engineer in charge
2
-
-
M&L for 15mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes, complete all as specified and as directed by Engineer in charge
2
-
-
M&L for coloured glazed ceramic tiles in vertical surfaces 350X250X7mm/ 450X350X 7mm thick as in skirting /dado, set and jointed in cement slurry and pointed in coloured cement to match laid over 10mm thick cement backing coat in CM 1:3 complete all as specified and as directed by Engineer in charge
40
-
-
Dismantling of wall and ceiling boards (fiber, pulp , insulation etc)or insulation boards /slabs /blankets any thickness including cover fillets, grid work any description and any position complete all as specified and as directed by Engineer in charge
100
-
-
S&F Aluminium anodised snap grid false ceiling of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM, grid size n.exc. 610 x 610mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab roof truss fixed with suitable size MS hook and fastening bolts etc including 'E' board classic 4mm thick oceanic sheet of size n.exc. 610 x 610mm size fixed in ceiling with clips to aluminium snap grid incl preparation of new surface and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engineer-in-Charge.
100
-
-
Taking down Cement Plaster of any description on PCC block walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer-in-Charge.
Note: Rate inclusive of scaffolding at any height
300
-
-
M&L for rendering 10 mm thick plaster in fair faces of PCC block wall or concrete surfaces in CM (1:6) finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.
200
-
-
M&L for rendering 5mm thick ceiling plaster in CM (1:3) on concrete surfaces finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.
100
-
-
M&L for providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, and similar works slightly rounded or chamfered angles and throating including necessary form work complete all as specified and as directed by Engineer-in-Charge.
2
-
-
M&L for applying two coats of oil bound distemper over a coat of primer on newly plastered surface of wall including preparation of surface, complete all as specified and as directed by Engineer-in-Charge.
200
-
-
M&L for applying two coats of oil bound distemper over a coat of primer on newly plastered surface of ceiling including preparation of surface, complete all as specified and as directed by Engineer-in-Charge.
100
-
-
M&L for providing and applying putty of 1 mm thickness over plastered surface of wall/ceiling to prepare the surface even and smooth complete all as specified and as directed by Engineer-in-Charge.
20
-
-
M&L for preparing new steel or iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.
20
-
-
M&L for preparation of new wood/wood based surfaces of exc. 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.
10
-
-
S&F Anodised Aluminium frames or shutters for doors, partitions, Windows and Ventilators and similar works with one or more rebates incl necessary fittings and fixture such as jointing cleats, glazing clips, rubber packings, screws, handles stainless steel adjustable friction stay hinges etc. as required fixed to aluminium frame complete all as specified.
NOTE: (i) Unit rate quoted shall deemed to include cost of rubber beading, fittings such as handles, SS friction stay hinges and fixing of glass, wire cloth & Decogrill etc. (ii) Glass, wire cloth & grill to be measured and paid separately.
215
-
-
Supply only 5.5 mm thick, Sheet glass, selected quality, in squares n. exc 0.5 Sqm each pane complete all as specified and as directed by Engineer-in-Charge.
15
-
-
Supply only 4mm thick, Figured glass, pinhead type in squares n exc 0.5 sqm each pane complete all as specified and as directed by Engineer-in-Charge.
15
-
-
Supply only Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction complete all as specified and as directed by Engineer-in-Charge.
100
-
-
Supply only Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge.
15
-
-
S&F in repair 5.5mm thick sheet glass ordinary quality in aluminum joinery in squares of area n.exc 0.50 sqm in each pane including necessary adjustements, dismantling and re-securing complete all as specified and as directed by Engineer-in-Charge.
15
-
-
S&F in repair aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge.
30
-
-
S&F in repair aluminium anodised Doors, windows and ventilators members any description for replacement of unserviceable members, Minor repair to any sections and making serviceable the same by means of adjustment, greasing, changing friction hinges if necessary etc complete all as specified and as directed by Engineer-in-Charge.
Note -Glass , wire mesh etc measured seperately on respective item of schedule
100
-
-
S & F anodized aluminum door seals of 32mm (overall size) with standard 1mm thick aluminum sections and bottom brush and provision of counter sunk holes for screws etc complete all as specified and as directed by Engineer-in-Charge.
30
-
-
S&F in repair Door closer hydraulically regulated, designation No. 3, universal type, aluminum extruded body suitable for door shutters of 851 to 1000 mm in width complete all as specified and as directed by Engineer-in-Charge.
5
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements