Military Engineer Services Tender
To inquire about any e-tender the Andaman & Nicobar Islands government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder one can find every eprocurement Punjab tender on BidAssist. BidAassist has collated each and every Eproc Andaman & Nicobar Island Tender on its website. Looking for Andaman & Nicobar Island tenders online or going through the cumbersome government websites for it, has been made easier with the help of BidAssist.
Military Engineer Services - MES Tender
Eprocure
Opening Date6 Apr 2024
Closing Date1 May 2024
Tender Amount₹ 43,50,000
Costs
EMD
₹ 87,000Document Cost
₹ 500Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MES_646020_1Bid Award Id
ViewTender No
8112/E8Tender Authority
Military Engineer Services ViewPurchaser Address
-Website
http://http://mes.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
M & L for providing 125mm thick PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation, sub base etc complete all as specified and as directed.
36
-
-
M & L for use and waste of timber as in formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter as in rough finished surfaces of concrete flat all as specified and as directed.
45.9
-
-
M & L for use and waste of timber as in formwork to sides of pillars, posts, struts, piers, column and stanchions for rough finished surfaces of concrete square, circular, rectangular on plan or polygonal all as specified and as directed.
27
-
-
M & L for RCC M30 (Design Mix) (using 20 mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs,under-reamed piles and mass concrete all as specified and as directed.
10
-
-
M & L for RCC M30 (Design Mix) (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts all as specified and as directed.
6
-
-
M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping for columns hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to Fe-410-S all as specified and as directed.
900
-
-
Description all as per Item No 9 above but 5 mm dia and over up to 10 mm dia as in stirrups, spacers and binders, complete all as specified and as directed.
240
-
-
S & F MS sections as in ISMC, ISWB, angle, main and cross beams, hip and jack rafters; purlins, rolled section where connected to common rafters and running rails and guides for truss /column / staircase /ladder /anchor (MS HSFGB Grade10.9S) bolt for columns/ base plates /gusset plates, wind tie, etc including cutting welding etc; fixed with angle cleats or other connecting plates complete all as specified and as directed.
4350
-
-
M & L for preparation of new /previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.
85
-
-
Removing excavated surplus soil to a distance exc 250m and n.exc 500m depositing where directed at a level n.exc 1.5m above the starting point all as specified and as directed.
10
-
-
E/M PORTION
Supplying and laying of 75mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and as directed.
55
-
-
Supplying and laying of 50mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and as directed.
45
-
-
Supplying and laying of 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified and as directed.
65
-
-
S & F of CPVC ball valve having dia 75mm including all necessary fittings complete all as specified and as directed.
4
-
-
S & F of CPVC ball valve having dia 50mm including all necessary fittings complete all as specified and as directed.
5
-
-
S & F of CPVC ball valve having dia 25mm including all necessary fittings complete all as specified and as directed.
5
-
-
Supply, testing, installation and erection of stainless steel tank of capacity 5000 litres, SS-316 grade, ISI marked, 5 layer including fixing of float valve, inlet/ outlet pipes complete all as specified and as directed.
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements