Military Engineer Services Tender

Supply and Fixing horizontal multistage centrifugal pumpset of capacity 12.5 HP, 3 phase, Head-150mtr, 10cum/hr including base frame and foundation as per manufacturer's design and electric connection with suitable size PVC insulated copper conductor cable drawing through and including flexible conduit from main control panel to starter and starter to motor including thimble of suitable size, and all necessary connection for suction and delivery pipes and all holding arrangements foundation complete all as specified and as directed by Engr-in-Charge.( RII TO RII EXT)

Supply and Fixing horizontal multistage centrifugal pumpset of capacity 7.5HP, 3 phase, Head-,60 to 70mtr 10cum/hr including base frame and foundation as per manufacturer's design and electric connection with suitable size PVC insulated copper conductor cable drawing through and including flexible conduit from main control panel to starter and starter to motor including thimble of suitable size, and all necessary connection for suction and delivery pipes and all holding arrangements foundation complete all as specified and as directed by Engr-in-Charge.

Returning filling, including spreading, leveling , watering and well ramming in layers not exceeding 25 cm in hard/dense soil, complete all as specified and directed by Engr-in-Charge.

M&L for removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as directed by Engr-in-charge.

M&L for earthing complete with galvanised steel earth plate 600x600x6mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connect to galvanised iron strip 32x6 6mm as earthing lead by means of bolts, nuts and washers of GI or steel including excavation and earth work, GI pipe medium grade 15 mm bore for protection of GI earth wire, GI pipe medium grade 20mm bore for watering, charcoal dust, common salt, PCC 1:2:4 type B1 chamber with CI PCC cover GI funnel and wire mesh all as shown in elect plate No.3 of SSR Part-I (2007) including connection and testing complete all as directed by Engr-in-Charge. Note:- Excavation & earth work deemed shall be deemed to be included in the quoted rate.

Supply and fixing PVC insulated, round seathed, electric cable with copper conductor, 1100 volts grade cross sectional area 10 sqmm, 3 core complete for motor connection complete all as specified and directed by Engr-in-Charge.

Supplying, transporting, erecting and fixing steel tubular swaged poles type 410 SP-55, 11.00 meter long, complete with cast iron base plate, final taper plug, bolts, nuts and screws as specified including painting with two coats of aluminium paint heat resistant type over one coat of red oxide primer and making 06 Nos bands/straps with white and black colour (30 cm wide each) synthetic enamel paint at a distance 30 cm from plinth block and numbering of poles with black bitumenous synthetic enamel paint in 2.5 cm height including tarring one coat on steel surface embedded in concerete foundation complete all as per specified and directed

Supply, installation, testing and commissioning (in ( R-II in HIll Sector ) of LT Panel board suitable for 415 Volts, 3 Phase 4 wire, 50 Hz AC supply system confirming to IS:8623/93, outdoor type floor mounted alongwith factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick with ingress protection of IP-54 grade having heat shrinkable sleeves, louvers and air vent gasket for natural flow of air “U” type gasket shall be used to make the outer shell completely vermin proof. The panel shall be front/rear openable and having inner & outer shells. The inner shell dully compartmented for each control gear, including powder coating internally and externally the entire steel surfaces. All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200 mm x 1200 mm x 450 mm , mounted on angle iron stand made out of angle size 50x 50 x 6mm grouted in PCC foundation in cement concrete 1:2:4 type B-1 platform 45 cm above the ground level and 30 cm below the ground level (using 20mm graded crushed stone aggregate), including accomodating the following gears and accessories :- (a) Digital Ammeter 0 to 500 Amps digital type with built in selector switch, CT's of suitable ratio (set of three) = 01 Set (b) Digital voltmeter 0 to 500 Volt digital with built in selector switch = 01 No (c) Indication Lamps LED Type (RYB) = 01 Set (d) Internal wiring of suitable size of copper conductor cable (e) Aluminium bus bar of capacity 200 Amp for three phases and 100 Amp for neutral. (f) MCCB 160 Amp 25 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (as incomer) (g) MCCB 125 Amp 16 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (O/G) (h) MCCB 63 Amp 16 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (O/G).

Supply and fixing control unit into sheet metal enclosure for motor mounted on suitable angle iron stand including all fixing accessories complete all as specified and directed by Engr-in-Charge. Note: Each control unit consist of MCCB 63 Amps-01 AND MCCB 100 Amp No, Single phase preventor-01 No, RYB indication light-01set, Ammeter 0-160A- 01 No, Voltmeter 0-500V-01 No and the cost shall be deemed to be included in the quoted rate.

M&L for 25mm brass GATE VALVES (brass insert) of dia 50mm as per requirement of the site complete all as specified and directed by Engr-in-Charge.

M&L for Non return valve of size 40 mm bore dia PN1.6, iron wheel head,screwed both ends for pipe including required GI fittings all as directed by Engr-in-Charge. Make : Kirloskar/Sant/Leader

Supply and laying GI water tubing 20mm bore with screwed socket joints, medium grade galvanised including all fittings, such as sockets, bends, elbows, unions, tees laid in trenches and taking out unserviceable tube complete all as specified and directed by Engr-in-Charge.

M&L for 40mm dia brss GATE VALVES of as per requirement of the site complete all as specified and directed by Engr-in-Charge.

Supply, laying, jointing, testing and commissioning of High Tension (HT) XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, heavy duty, earthed electric power cable, cross sectional area 95 Sqmm 3.0 core aluminum conductor 11000volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, from Tropo post to R-I extn in hill sector complete all as specified and directed by Engr-in-Charge.

M& L for cross arms, bracings, suppots, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed by Engr-in-Charge.

Constructruction of platform for single transformer & Panels of size 2.50m X 2.50mX1.20 m high from natural ground level with brick walling including steps, XPM fencing fixed on angle iron posts upto 1.0m height with gate and locking arrangement, painting including top shed of CGI sheet for protection from rain and snow falling, complete all as specified (R-1 extn in Hill sector) and directed by Engr-in-Charge.

Supply and installation of copper wound transformer step down outdoor type complete with standard fitting HT 11KV 3 phase, LT 433 volts 3 phase 4 wire with off load tapping on HT side to vary secondary voltage within limit all as per IS 2006 of capacity 100 KVA complete all as specified and directed by Engr-in-Charge.

Supply and Fixing horizontal multistage centrifugal pumpset of capacity 25HP, 3 phase, Head-288 TO 310mtr, 10cum/hr including base frame and foundation as per manufacturer's design and electric connection with suitable size PVC insulated copper conductor cable drawing through and including flexible conduit from main control panel to starter and starter to motor including thimble of suitable size, and all necessary connection for suction and delivery pipes and all holding arrangements foundation complete all as specified and as directed by Engr-in-Charge.

Supply, installation, testing and commissioning (in ( R-II Extn in HIll Sector ) of LT Panel board suitable for 415 Volts, 3 Phase 4 wire, 50 Hz AC supply system confirming to IS:8623/93, outdoor type floor mounted alongwith factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick with ingress protection of IP-54 grade having heat shrinkable sleeves, louvers and air vent gasket for natural flow of air “U” type gasket shall be used to make the outer shell completely vermin proof. The panel shall be front/rear openable and having inner & outer shells. The inner shell dully compartmented for each control gear, including powder coating internally and externally the entire steel surfaces. All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200 mm x 1200 mm x 450 mm , mounted on angle iron stand made out of angle size 50x 50 x 6mm grouted in PCC foundation in cement concrete 1:2:4 type B-1 platform 45 cm above the ground level and 30 cm below the ground level (using 20mm graded crushed stone aggregate), including accomodating the following gears and accessories :- (a) Digital Ammeter 0 to 500 Amps digital type with built in selector switch, CT's of suitable ratio (set of three) = 01 Set (b) Digital voltmeter 0 to 500 Volt digital with built in selector switch = 01 No (c) Indication Lamps LED Type (RYB) = 01 Set (d) Internal wiring of suitable size of copper conductor cable (e) Aluminium bus bar of capacity 160 Amp for three phases and 80 Amp for neutral. (f) MCCB 125 Amp 36 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (as incomer) (g) MCCB 63 Amp 16 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 03 No (O/G)

Supply, installation, testing and commissioning (in ( R-I Extn in HIll Sector ) of LT Panel board suitable for 415 Volts, 3 Phase 4 wire, 50 Hz AC supply system confirming to IS:8623/93, outdoor type floor mounted alongwith factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick with ingress protection of IP-54 grade having heat shrinkable sleeves, louvers and air vent gasket for natural flow of air “U” type gasket shall be used to make the outer shell completely vermin proof. The panel shall be front/rear openable and having inner & outer shells. The inner shell dully compartmented for each control gear, including powder coating internally and externally the entire steel surfaces. All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200 mm x 1200 mm x 450 mm , mounted on angle iron stand made out of angle size 50x 50 x 6mm grouted in PCC foundation in cement concrete 1:2:4 type B-1 platform 45 cm above the ground level and 30 cm below the ground level (using 20mm graded crushed stone aggregate), including accomodating the following gears and accessories :- (a) Digital Ammeter 0 to 500 Amps digital type with built in selector switch, CT's of suitable ratio (set of three) = 01 Set (b) Digital voltmeter 0 to 500 Volt digital with built in selector switch = 01 No (c) Indication Lamps LED Type (RYB) = 01 Set (d) Internal wiring of suitable size of copper conductor cable (e) Aluminium bus bar of capacity 260 Amp for three phases and 130 Amp for neutral. (f) MCCB 200 Amp 36 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (as incomer) (g) MCCB 160 Amp 36 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 01 No (O/G) (h) MCCB 63 Amp 16 KA, 4 pole wih adjustable thermal and adjustable magnetic setting with spreader links on both sides (IS/IEC 60947/2) = 02 No (O/G)

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, screened, stranded aluminum conductor 1100 Volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through roads etc, from R-I extn to Kali extn in hill sector complete all as specified and as directed of following cross sectiional area and sizes :-

Supply and laying GI water tubing 25mm bore with screwed socket joints, medium grade galvanised including all fittings, such as sockets, bends, elbows, unions, tees laid in trenches and taking out unserviceable tube complete all as specified and directed by Engr-in-Charge.

Supply and laying/fixing, GI pipe light grade 100 mm dia bore for cable protection fixed to pole/wall or laid under floor/road/pavement, including taking out old & removal, complete all as specified and directed by Engr-in-Charge.

Earthing complete with galvanised steel earth plate electrode 600mm X 600 mm X 6 mm thick burried directly in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to and including GI strip 25 x 4 mm thick thick as earthing lead by means of steel bolts,nuts, check nuts and washers test points made of GI strip 25 x 4 mm, 10 cm long ,PCC 1:2:4 type B-1 in pit, angle iron 25X25X3mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways abd 12mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mess and light grade GI protection pipe 40mm bore upto 5m length for drawing in earth lead ,salt,charcol etc. including excavation and earth work in any type of soil , removal of surplus soil to a distance not exceeding 50m complete all as shown in electrical plate No. 3 of MES schedule 2009 part-I and connected complete all as specified including testing on completion complete all as specified and directed by Engr-in-Charge.

Supply and fix Switch air break gang opertated tripple pole mechanically operated from ground level mounted on 12 insulators outdoor type suitable for vertical instatllation single break provided with locking arrangement for operating handle including seven levers "Navtal" lock consisting of mild steel channel HT post top insulator copper alloy high pressure assembly with drop out expulsion fuses for phases, operating rod of 25 mm dia medium grade G.I. pipe complete conforming to IS-1018 of 1972 with continuous current rating 200 Amps 11KV grade complete all as specified and directed by Engr-in-Charge.

Supplying, installation, commissioning and testing of (level 2) transformer step down 11/0.433KV capacity 100 KVA, out door type copper wound 3 phase, 4 wire, 50 cycles per second, oil immersed naturally cooled external cooling tube core type delta connection on primary side (HV side) and star connection on secondary side (LV side) having tapping + 2.5%, 5%, 7.5%, 10% to be charged by means of hand operated, off load/tap changing gear including first filling of new transformer oil of dielectric strength not less than 60 KV with standard fittings such as two earting terminals for body and one additional for neutral brought out inbushing, oil level gauge indicator for level minimum and maximum, lifting lugs, rating and terminal plate, plain breather device with silica gel to prevent ingress of rain water and inserts, drain cum sampling valve 20mm bore steel with plug,dial type thermo meter, oil filling hole 32mm threaded with plug. The transformer shall be powder coated for water/dust and vermin proof.Note:- Transformer oil shall be conforming to requirements of IS-335-1993rec-2005 specification for new insulating oil for transformers. The transformer shall be IS-1180 (Part-I) 2014 with maximum total loses as per energy efficiency level-2 of IS:1180 (Part-I 2014) complete all as specified and directed by Engr-in-Charge. Note :- Transformer will be installed in R-1 Extention in Hill sector. All T&P required for installation is included in quoted rates.

(a) 95 sqmm, 3.5 core complete all as specified and directed by Engr-in-Charge.

Supply and fixing Star Delta starter, oil immersed, initial oil filled, 3 phase, 50 c/s, 440 V suitable for 30 HP pumping set for heavy duty type: SSD complete all as specified and as directed by Engr-in-Charge. Make BCH

M&L for returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as directed by Engr-in-charge.

M&L sand cushioning to underground cables 8 cm below the cable before laying and 15 cm above the cable after laying, and streching the cable complete welll ramming/compressed the sand upto 18 cm complete all as specified and directed by Engr-in-Charge.

S&F PVC four layer water storage tank of capacity 2000 ltrs including required PCC works complete all as specified and as directed by Engr-in-Charge.

Removal of excavated material i.e soil to a distance not exc. 50m and depositing where directed at a level not exceeding 1.5 mtr above starting point complete all as specified and directed by Engr-in-Charge.

Supply and laying GI water tubing 40mm bore with screwed socket joints, medium grade galvanised including all fittings, such as sockets, bends, elbows, unions, tees laid in trenches and taking out unserviceable tube complete all as specified and directed by Engr-in-Charge.

(b) 25 sqmm, 3.5 core complete all as specified and directed by Engr-in-Charge.

M&L for excavating in trenches not exceeding 1.5mtr wide and not exceeding 1.5mtr in depth for laying of GI pipeline of 40mm bore dia all as specified and directed by Engr-in-Charge.