Zilla Parishad Tender

Supply of galvanised iron socket with ISI mark

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but WCluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed The item includes necessay bi.mming the sides of trenahes, levelling, dressing and ramming the bottom, bamng out water as required complete (a) Depth of excavation not exceeding 1,500 mm.

Cement concrete with 30 mm down graded shingels excluding shuttering. N.B Veriety In Ground floor ( 1:3:6) Propotion

Ordinary Cement concrete. mix (1:1 ½ :3) cement concrete with graded stone chips 20mm size.

Hire and labour charges for shuttering with centering etc. complete 25mm to 30mm shuttering with out staging in foundation)a) 25 mm. thick to 30 mm.thick wooden Shuttering

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.

Plaster (to wall floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed with 1:4 cement morter 20mm thick

125mm. thick brick work with cement mortar (4:1) with 1st class bricks

Neat cement punning about 1.5 mm thick

Construction of soak galery (600 mm X 450 mm) with lwo layers of jhama metal/Brick bats (38 mm to 50 mm size) 150 mm thick and 3 layers of dry brick Hals in betwen the layers of jhama metal leaving an opening of 10 mm X 150 mm ,n section along the G.L as per sketch including cuting trenches in required 13 grade.back filing and compacting torts ongm~ G.L etc. complete mcludmg costs of labour and mJenals ..P. No 90 Item NO-6 (PWD S&P)

M S. structural works in columns, beams etc. with simple rolled structural members (e g joists, angle, channel sections conformingto IS 226, IS: 808 & SP (6) 1964 eonneoted to one another withbraclet. gussets, cleats as per design, direction of Eng1neer-mcharge complete including cutbng to requisite shape nnd length.fabrication with necessary bolting, metal arc welding conforming tors• 816-1956 & IS: 1995 using electrodes of ~proved make and brand 14 confoonlng to 15•814-1957, haulage hoisting and erectionall complete. The rate includes the cost of rolled steel section.consumables such as electrodes, gas and hire charge of all toolsand plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. I) For structural members of specified sections weighing less than 22.5 Kglm.P. No ~ Item NO. 1

b) Priming one coat on steel or other metal surlace with synthetic oil bound pnmer of approved quality including smoothening surfaces by sand papering 15 etc. (b) On steel or other metal surface With super gloss (hi-gloss)• [iv) Two coats (with any shade except white) P. No 200 Item NO. 1-a)

A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of I Approved putty etc on the surface. 1f necessay 16 (b) On &1ool or other metal surface With super gloss (hi-gloss)- (iv) Two coats (with any shade e~ceptwhite).P. No 200 Item NO. 2-b)-lv

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved mde confooning to IS-15778: 2007. with all necessary accessories, specials viZ. socket, bend tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials.(Detailsm bill)::: (a) For Exposed Work;:: (ii) CPVC Pipes Class-2,SDR-13.5 ::: 25 mm::: P. No 29 Item N0.1-lij

Supplying P V C. water storage tank of approved quality with closed top wrth lid (Black) • Multilayer ::; (a) 1000 litre capacity P. No 37 Item NO. 6-a)

Supplying, fitting and fiXing pillar cock of approved make. d) Polythene Piller Cock (EMCO I ATLAS or equivalent) Q) 15 mm:::

WRDD SCHEDULE,Page - 109 / Item - 1(b) PV Module : Supply , transport , installation and commissioning of Solar PV installation for water pumping system with fixed structure consisting of solar panels framed in anodized aluminium frame mounted on stable hot dipped galvanized (with 80 micron thickness) mild steel structure of sufficient strength which can withstand load of modules and high wind velocities upto 150 Km/hr, having RCC foundation designed against all possible loads (Dead, Live and imposed load). Modules supplied with the SPV system should have certificate as per IEC 61215 specification or equivalent National or International standards and must be interconnected with 4/6 sq.mm cables routed in PVC conduits properly fitted along the G.I structure to provide a good aesthetic view. Modules must qualify to IEC 61730 part I and part II for safety qualification testing. The power output of individual PV modules used in the PV array, under STC, should be a minimum of 250 Watts peak, with adequate provision for measurement tolerances. Solar cells should be crystalline silicon cell with min. efficiency of 14% and fill factor more than 70%, should be laminated between sheet of -Ethylene Vinyl Acetate (EVA) and high transmissivity 3.2mm tempered glass including appropriate DC to AC inverter and power controlling unit (protected with IP65 class enclosure) with MPPT technology to run at low sunshine and minimum 5 hours a day run with all necessary accessories suitable for solar + grid operation and including all protections of AC induction motor pump. There should be a display of all measurable parameters including storing of data at a set interval and transfer it in a pendive thru USB port . There should also be provision of interfacing GPRS based data transmission. (The rate is inclusive of manufacturer's warranty and comprehensive maintenance for 1st year and comprehensive maintenace for 4 years beyond Ist year)

WRDD SCHEDULE,Page - 114 / Item - 2(i) Supplying , fitting and fixing of Sand Filter - Manual as per IS:14606 Sand Filter10m³/hr-M Single

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe

Connecting the equipment to the earth busbar incl. S&F GI wire of size bellow on wall /floor as required and making connection to the equipment with bolts, washers, cable lugs etc. as required and mending good damages. No 4 SWG GI wire

Installation of submersible electro motor pumping set of following capacities by using necessary requisite, tools and plants by lowering the same within the tubewell housing pipe upto the following depth as per direction by fitting, fixing column pipes and other accessories, fixtures with necessary nuts, bolts and washers and suspending the entire assembly of pump set vertically by fixing the same supported by M.S. clamps over the top of housing pipe, binding the motor cable with each column pipes and drawing cable upto pump controller/starter point including opening out of the top cap of housing pipe of the tubewell and testing of motor both in loading as well as in unloaded condition before and after installation of the same. (The rate is inclusive of hiring charges of tools & plants.) (b) 30 cubic metre per hour capacity electro motor pumping set. (i) Length of pump assembly not exceeding 18 metre length

Supplying 1 m × 0.6 m × 24 swg MS board containing list of spout wise water users by making numbers of spout as directed by EIC. The board should have base colour - Black and words - White to be fitted and fixed on the wall of the pump house.

Supply of 1 HP oil fill AC solar submersible pump motor set complete having suitable dischage as per yeld test of well. Submerisble cable of 30mtr 3 core 2.5 sqmm that cable (Finolex) with MOC bar chart (Kriloskar make Pump) (Rate As per Quotation

Supply fitting fixing of 38 mm dia column pipe having 3.04 mtr length including supply and fixing one socket at one end

Supply & Fixing Information Sign Board 1000x500mm fabricated with MS Sheet 18SWG and ISA frame 25x25x4mm including Painting and lettering with approved paint as per instruction of authority

Add GST 18%

Add Cess 1 %