Zilla Parishad Tender

Ordinary cement concrete M-20 (mix 1:1.5:3) with graded stone chips (20mm down) excluding shuttring and reinforcement, if any, in ground floor as per IS-456-2000.i). With River bazree

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction.For works in foundation, basement and upto roof of ground floor/upto 4m. ( Details to be in bill) L.S. (JSW/JSPL/SHYAM/ SRMB/ BMASL/ ELECROSTEEL/SSL)

Hire and labour charge for shuttering with centreing and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (upto roof of ground floor)25 mm. to 30 mm. thick wooden shuttering as per ( Details to be in bill) L.S.

a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.Grill weight @ 8 Kg / M2=69.3 Kg

Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) ofsize 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut atjunction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mm M.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to be providedasgapinsert. Thedoorframetobefixed withwall byusing 8mmdia. and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos. screws to be provided for each vertical member & 2 nos. for horizontal member all complete as per direction of Engineer-in-Charge.

Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive.

25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days of concrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer based paint to be paid separately).( Chequering not required over concrete or painted surface). [Note: - Waterproofing as per item NO 60, polymer based paint as per item 59 (a) of Section (C)

Brick work with 1st class bricks in cement mortar (6:1)a). In foundation and plinth

Brick work with 1st class bricks in cement mortar (6:1)b). In super structure of Ground floor

125 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor.

Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints or roughening of concrete surface, including throating, nosing and drip course where necessary (ground floor).a). 20 mm thick plaster with 6:1 cement mortar

b). 15 mm thick plaster with 4:1 cement mortar

c). 10 mm thick plaster with 4:1 cement morter

Priming one coat on timber, plastered or on steel or other metal surface with synthetic enamel/oil bound prinmer of approved quality including smoothening surfaces by sand papering etc. a). On steel surface

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand parpering etc. in cluding using of approved putty etc. on the surface , if necessary.On steel surface withany shade except white. Two coats.

Iron butthinges ofapproved quality fitted and fixed with steel screws, with ISI mark.(iii) 75mm. X 40mm. X 1.12mm.

Iron secket bolt of approved quality fitted and fixed complete.100 mm long x 10 mm dia bolt For door

Anodised aluminium D- type Handle ………do …….do. 75x45x25 mm size

Neat cement punning about 1.5 mm. thick in wall, dado, window, sills, floor, drain etc.

Apply Decorative cement based paint approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. ii) Two coats

Add Sanitary & Plambing work @7.5%

Add GST@18%

Add CESS@1%