Zilla Parishad Tender

Supplying, fitting and fixing plug of approved make conforming to I.S. specifications. (ii) 75 mm

Supplying,fitting and fixing check valve (horizontal) G.M. tested to 21 kg per sq. cm.

Supplying, fitting and fixing heavy type bell mouth reducing socket. (i) 50 mm X 100 mm

Supplying, fitting and fixing 300 mm M.S. housing clamp of approved quality.

Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). withall necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials. (d) For depth upto 150 metre for 50 mm dia. tube well with top enlargement of 100 mm dia. (i) 80 mm dia.

Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). withall necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials. (d) For depth upto 150 metre for 50 mm dia. tube well with top enlargement of 100 mm dia. (i) 150 mm dia.

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work (ii) CPVC Pipes Class-2,SDR-13.5 50mm

Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches or drain in all sorts of soils (including mixed soil but excluding laterite or sand stone) including removing spreading ro stacking the spoils within a lead of 75 m, as directed including trimming the side of trenches, levelling dressing an raming the bottom, bailing out water etc. as required complete. a) Depth of excavation not exceeding 1.5 m

Earth Work in filling of foundation trenches of plinth with good earth in layers not exceeding 15cmm including watering ramming etc.layer by layer complete ( payment to be made on the basis of measurement of finished quantity work) (a)With earth obtained from excavation of foundation. (a)With earth obtained from excavation of foundation 1/ 5 th of item no

C) (iv) With carried earth arranged by the contractor within a radius exceeding 5 km. butnot exceeding 10 km. including cost of carried earth

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. a) 1:3:6 proportion

Brick work with 1st class bricks in cement morter (1:6) (a) in foundation and plinth

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (ii ) River Bazree

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel I. SAIL/TATA/RINL

Hire and labour charge for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slab, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto the roof of ground floor) a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. Ground Floor

Plaster (to wall, floor, ceiling etc) with sand - cement-morter including rounding off and chamfering corners as directed and racking out joints including throating, noising and drip course, scaffolding / staging where necessary ( Ground floor) (excluding cost of chipping over concrete surface ) i)With ( 1:6 ) Plaster b) 20mm thick

Neat cement plunning about 1.5mm thick in wall dado, window sills, floors, drains etc. using cement @ .152 cu m/100 sq m

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (b) Extra for work in grill gate. (I) For hanging and locking arrangements including supply of materials and labour complete. (15% extra over the corresponding item of grill ) (@ Rs = 10021 x 15% = 11524.15)

b) Primer one Coat on steel or other metal surface or on steel or other surface with synthetic enamel / oil bound primer of approved quality including smmothening surfaces by sand papering etc.

A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface throughly by sand papering etc. including using of approved putty etc. on the surface, if necessary. (b) on steel or other metal surface (two coats) with other than hi-gloss of approved quality iv) Two coats ( with any shade except white)

Applying decorative cement base paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concreted surface) as per manufactures specification, (two coats)

Solar Module: Supply, transport, installation and commissioning of ISI marked solar module as per following specification. 1. Cell: Indigenous mono crystalline silicon SPV cells. 2. Solar Module: Monocrystalline cell with PERC technology/module with bifacial cell 3. Standards: ISI marked as per IS 14286 and having certification of IEC 6183(1), 61730(1&2), 61710 4. Modules must quality to IS 170210(Part 1) 5. Min efficiency 19.5% 6. Fill factor: More than 75% 7. Module wattage mismatch in the SPV array: within +3% 8. Wattage output warranty: Should be less than 90% at the end of 10 years and 80% at the end of 25 years. 9. Power output of individual PV modules used in the PV array, under STC minimum 300Wp. Necessary test certificate also to be supplied. For detail information please see cl. No 2.1 of technical specification. b) For 2HP Off-Grid Solar water Pumping System with Monocrystalline/ Monocrystalline PERC/bifacial SPV Modules

Module Mounting Structure: Supply, transportation & Installation of GI manual tracking/Fixed structure made of MS Hollow Section, Pipes, Plates, angles etc as per IS4923, IS:1161/1239, IS:1079/2062, to hold min 300Wp SPV Module as per drawing and technical specification. The steel structure is to be protected with minimum 80 micron galvanization (hot dip) and provided with fixed arrangement of dual axis manual tracking arrangement for three times in a day and seasonal lilting to face the sun optimally.

Power conditioning unit with enclosure: Supply, transportation, Installation and commissioning of Solar Power Conditioning Unit consisting of following components and features 1. Variable frequency Drive with inbuilt MPPT, Voltage range suitable for operation pump-motor set of 1HP to 20 HP, detail mentioned in cl 6.1 2. Power input: DC source for 1HP, 2HP and 3HP 3. Power input: AC/DC source or hybrid for 5HP and above 4. Incomer: DC MCB 2 Pole 16 amp upto 5HP, 25 amp for 7.5HP and 10HP, 40 amp for 15 to 20 HP as per IS/IEC 60947-2 5. Incomer: AC MCB 4 Pole 16 amp upto 5HP, 25 amp for 7.5HP and 10HP, 40 amp for 15 to 20 HP as per IS/IEC 60947-2 6. Type II DC SPD of 40 KA 7. Type II AC SPD 40 KA for AC/DC or Hybrid input 8. Dual input (Solar/Grid) 25 amp changeover switch for 5H and 7.5HP, 40 amp for 10HP, 63 amp for 15 to 20 HP 9. Reverse protection diode 1600 VDC with heat sink 10. Data logger 11. Remote monitoring system 12. Should have built –in EMC filters 13. IP 65 glands for cable in and out 14. Min. IP 54 enclosure. For details features, protection, RMS, communication architecture, security Data storage, tolerance or various parameters, standards to be qualified, etc. please refer to cl. 6.1 of technical qualification. 3) For 3HP Pump Motor Set with DC input

Cable and Accessories: Supplying, fitting and fixing of UV rated Copper cable laid inside HDPE conduit and other accessories as per following with necessay connection with the Solar PV Module, MPPT etc I. 4.0 Sqmm Single core multi studs-5m (for 1HP/2HP/3HP) ii. Lugs, HDPE Pipe, Flexible pipe, saddle, cable tie etc a) For 1HP/2HP/3HP per structure

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe including excavation of soil for installation of each electrode and filling & ramming and connection to individual structure to earth electrode including S&F 20mmx3mm galvanized (Hot Dip) MS flat on Wall/floor with GI saddles as required and connecting to equipments incl. drilling holes, with bolts, nuts, washers etc.

Lighting system a scheme (with lighting Pole) Dusk to dawn lighting arrangement at 4 mts height above ground level, with Hot dip Galvanised 80mmx50mm, medium duty pipe with 12V, 15Ah 2-in-1 Lithium ion/Ferro- Phosphate battery with in-built 7-11 Watt LED lamp, 50 Wp solar panel (min 19% eff.) to cover the scheme area. The lighting system should be warranted for 5years for the date of installation

Lighting protection (Pole mounted): Lighting protection with 3”x1.5” GI pipe of 6m+1m height with base flange in proper RCC foundation and S&F Lighting Conductor Air Terminal made of 20mm dia 1000mm long GI pipe (ISI Medium) having five discharge prongs of 4SWG GI (Hot Dip) wire at top duly soldered with 7/16 stranded GI (Hot Dip0 wire and 85 mm dia 6mm thick GI base plate at bottom incl. necessary holes etc. Eating with 65mm dia GI pipe (Medium) 3.0mts long and 1/9/10 stranded GI (Hot Dip) wire (4 mts long) 20mm dia x125mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire crimping sockets/ thimbles and S&F 65mm dia GI Pipe (ISI-Medium) protection (3 mts. Long) to be filled with bitumen partly under the ground level and partly above the ground level to an average depth of 3.65 Mts. Including connection to earth electrodes with 25x6mm GI strips

Supply and Installation of 3 Phase AC electromotor Pump-motor set with speed of 3000 rpm (synchronous speed) suitable for Solar applications and shall have 60 months guarrentee for folloing conditions including loading, unloading, transportation etc c) 3HP 3 Phase AC surface mounted Monoblock Pump Motor having discharge at required head as below: i) Surface pump-motor set for STW, as per IS:9079 with discharge of 6.5-7.14Lps at 16mts. total head with foot valve, required quantity of flexible suction pipe(15m) clamps, bend, footvalve and all others accessories to complete connection of suction and delivery side.

Testing and commissioning of scheme after completion of all work

Add GST 18%

Add Labour Cess 1%