Zilla Parishad Tender

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Cement concrete with 30 mm down graded shingles excluding shuttering. N.B. Variety (a) 1:3:6 proportion

Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes. (ii) River bazree

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, bindersetc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(I) Tor steel/Mild steel I. SAIL/TATA/RINL

Hire and labour charges for shuttering with centering and necessary staging up to 4 m. using approved stout prop and thick hard wood planks of approved thickness with required bracing for concrete slab, beams, columns, lintels curved or straight including fitting, fixing, and striking out after completion of works. (upto roof of ground floor.) (f) 25mm to 30mm shuttering without staging in foundation etc.

Hire and labour charges for shuttering with centering and necessary staging up to 4 m. using approved stout prop and thick hard wood planks of approved thickness with required bracing for concrete slab, beams, columns, lintels curved or straight including fitting, fixing, and striking out after completion of works. (upto roof of ground floor.) (a) 25 mm to 30 mm thk wooden shuttering as per decision & direction of Engineer-In-Charge.

Brick work with 1st class bricks in cement mortar (6:1) a) In foundation and upto plinth

125mm thik brick work with1st. Class briks in cement mortar (4:1) in ground floor.

Plaster(wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as dir-ected and raking out joints or roughening of concrete surface, including throating, nosing and drip course where nece With 6:1 cement morterssary. 20 mm thick plaster

Plaster(wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as dir-ected and raking out joints or roughening of concrete surface, including throating, nosing and drip course where nece With 6:1 cement morterssary. 15 mm thick plaster

Plaster(wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as dir-ected and raking out joints or roughening of concrete surface, including throating, nosing and drip course where nece With 4:1 cement morterssary. 10 mm thick plaster

Neat cement punning about 1.5 mm th. In wall, dado, windowsill, floor drain etc. NOTE :Cement0.152cu.m.per 100sq.m.

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. In Ground Floor Two Coats

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.

Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore (d) For depth upto 150 metre for 50 mm dia. tube well with top enlargement of 100 mm dia. (ii) 100 mm dia. boring etc. top enlargement

Labour for boring tube well of required dia. by water jet system through any type of soil strata including hire and labour charges for boring pipes, scaffolding, tools and plants as necessary and taking out them and lowering pipes, strainers, blind pipe etc. and fitting and fixing the same complete including bucket washing and other incidental works in the connection. The tube well should have a minimum 50 mm gap in between the outside of the tubewell pipe and the bore (d) For depth upto 150 metre for 50 mm dia. tube well with top enlargement of 100 mm dia. (i) 50 mm dia. boring etc.

Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239(i) 50 mm dia. boring etc. (A) PVC Pipe 100 mm

Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239(i) 50 mm dia. boring etc. (A) PVC Pipe 50 mm

Supplying PVC strainer of approved make with adapter conforming to I.S.12818 specifications. (ii)50 mm dia

Supplying, fitting and fixing steel cutter piece upto 450 mm long with sockets. (ii)50 mm dia

Digging earth in any soil including mixed soil but excluding moorum, laterite sand stone or any other hard stone including spreading or stacking the spoils within a lead of 75 metres as directed bailing out water upto 1 metre depth, shoring etc., when and if required and back filling with fine sand (including cost of sand) on completion of steining works. A) R.C.C. Ring Well i) 1.2 metre diameter of digging for 0.9 metre internal diameter of well ring a) Upto 3 metre below G.L.

R.C.C. well ring made with cement concrete 1:1.5:3 with stone chips and 0.80% reinforcement (including the cost of shuttering and reinforcement) cast at site fitted and fixed in position after proper curing true to plumb in the well including jointing with cement mortar 1:2 complete as per direction b) 65 mm thick and 1.2 metre internal dia Cement for joint filling-6 Kg/m a) Upto 3 metre below G.L.

Supplying, fitting and fixing CPVC (ChlorinatedPolyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessaryaccessories, specials viz. socket, bend, tee, union, cross, elbo, nipple,longscrew, reducing socket, reducing tee, short piece etc.fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respectincluding costof all necessary fittings as required,jointing materials in any position above ground. (Payment will bemade onthe centre line measurements of total pipe line including all specials. No separate payment will bemade foraccesories, specials. For Exposed Work (ii) CPVC Pipes class-2 ,SDR-13.5

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer (b) 1000 litre capacity

Labour for hoisting plastic water storage tank (i) Upto 1500 Litre capacity. (a) Upto 1st story from GL

Supply of Chlorinated Polyvinyl Chloride (CPVC) pipes & fittings conforming to IS-15778: 2007 25 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length 110 mm (b) 110 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length 110 mm (iii) Door Tee, (b) 110 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length 110 mm x) Bend 87.5² (b) 110 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length 110 mm xv) Vent Cowl (b) 110 mm

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length 110 mm Li) Nahani Trap. 90 mm

Supplying, fitting and fixing bib cock or stop cock (g) Supplying, fitting and fixing alloy iron with brass spindle bib cock/ stop cock of approved brand and make, spray painted and tested to 21 kg per sq. cm. 15 mm

Supply, transport installation and commissioning of solar PV installation for water pumping system with fixed structure (on roof) consisting of solar panels framed in anodised aliminium frame mounted on stable hot dipped galvanised (with 80 micron thickness) mild steel structure or sufficient strength which can withstand load or modules and high wind velocities upto 150 Km/hr, having RCC foundation designed against all possible loads (Dead, Live and imposed load). Modules supplied Wlth the SPV system should have certificate as per IEC 6121S specification or equivalent National or International standards and must be intcrconnectcd with 4/6 sq.mm cables routed in PVC conduits properly fitted along the G.I Structure to provide a good aesthetic view. Modules must qualify to IEC 61730 part I and part II for safety qualification testing. The power output or individual PV modulcs used in thc PV array, under STC, should be a minimum of 250 Watts peak, with adequate provision for measurement tolerances. Solar cells should be crystalline silicon cell with min. efficicncy of 14% and fill factor more than 70%, should be Iaminatcd bctween sheet of Ethylene Vinyl Acetate (EVA) and high transmissivity 3.2mm tempered glass. Including appropriate DC to AC Inverter and power controlling unit (protected wlth IP65 class enclosure) with MPPT technology to run at Iow sunshine and minimum 5 hours a day run wlth all necessary accessories suitable for solar + grid operantion and includintl all protections or AC induction motor pump. There should be a display of all measurable parameters including sorting of data at a set interval and transfer it in a pendrive through USB port . There should also be provision of interfacing GPRS based data transmission. (The rate is inclusive of manufacturer's warranty and comprehensive maintenance for 1st year and comprehensive masintenece for 4 years beyond 1st year)

Suppying fitting and fixing and installation of water pump with motor 1 HP 5 metre head suitable for 100 mm dia tube well etc including all (Bis satndards & including panel board 1HP)

Collecting sample of water for bacteriological and chemical test from any depth at any time during execution of work including hire and labour charges for tools and plants and sterilising the equipments, paying all charges and fees, testing etc. complete in all respect as per direction.

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. On steel surface

Painting with best quality synthetic enamel paint of approved make including smoothening surfaces thoroughly.. Two coat. On steel surface With super gloss (hi-gloss) (iv) Two coats

M.S. & W.I. Ornamental grill of approved design with MS flats or bars with joints continuously welded for windows railing etc. fitted and fixed in position with lugs and screwsand lugs in G.F. (i) Grill Weighting about 10kg/sq.mtr upto 16 kg/sq.mtr