Zilla Parishad Tender

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.

Reinforcement for reinforced concrete work in all sorts of structures …. And binding with 16 gauge black annealed wire….as per drawing and direction. For works in foundation, basement and upto roof of ground floor/upto 4m. Tor steel--------- JSW/SRMB/SHYAM/ELECTROSTEEL

Hire and labour charges for shuttering with centering and necessary stagingupto 4 m using approved stout props and thick hard wood planks of approvedthickness with required bracing for concrete slabs, beams and columns,lintels curved or straight including fitting, fixing and striking out aftercompletion of works (upto roof of ground floor) (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.

First class Brickwork in cement-sand mortar (1:6) (a) foundation and plinth

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor

75 mm thick brick work with 1st class bricks set in cement, sand mortar (1:4) including H.B. neting in every alternate layers

Supplying P.V.C. water storage tank of approved quality with closed topwith lid (Black) - Multilayer a) 500 litre capacity

Labour for hoisting plastic water storage tank. (i) Upto 1500 litre capacity. (a) Upto 1st story from G.L.

Labour for punching hole in plastic water storage tank upto 50 mm dia

Supplying, fitting and fixing shower of approved brand and make. (g) PTMT overhead shower ( Prayag or equivalent) (i) 75 mm round

(a) M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of railing etc. fitted and fixed with necessary screws and lugs in groundwindows,floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thickcement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m.

25mm. thick damp proof course with cement concrete with stone chips (1:1,5:3) ……..

Artificial stone in floor, dado, staircase etc with cement concrete(1:2:4) with stone chips, laid in panels as directed with toppingmade with ordinary 3 mm. thick topping (High polishing grinding on this item is notpermitted with ordinary cement).

Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excludingcost of chipping over concrete surface] (i)With 1:6 cement mortar (c) 15 mm thick plaster Ground Floor

ii) With 1:4 cement mortar (c) 10 mm thick plaster Ground Floor

Labour for Chipping of concrete surface before taking up Plastering work. Ground floor ceiling

Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet mitercut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided throughout the frame. The door frame shall be fixed with the wall using 65/100 mm longM.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for each vertical member and minimum 2 Nos forhorizontal member etc. complete as per Manufacturer‟s specification anddirection of Engineer-in-Charge.

Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC DoorShutter consisting of outer frame made out of M.S. tubes of 19 gauge thicknessand size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have costof steel primers of approved make and manufacture, M.S. frame covered with 5mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out ofwhich 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle oneither sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top &bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock railsshall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm widecross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th.both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles&rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner sideand joined together with solvent cement adhesive. An additional 5 mm th. PVCstrip of 20 mm which is to be stuck on the interior side of the “C” channel usingPVC solvent adhesive etc. complete excluding all necessary hardwares as perdirection of Engineer-in-Charge. In ground floor

Supplying, fitting and fixing M.S. clamps for door and window frame made of flatbent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) asper direction. (Cost of concrete will be paid separately) (c) 40mm X 6mm, 125mm Length

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISImark. (iii) 75mm. X 40mm. X 1.12mm.

Iron socket bolt of approved quality fitted and fixed complete (a) 75mm long x 10mm dia bolt.

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.

White washing including cleaning and smoothening surface thoroughly. (c) Three coats (on new works only).

Colour washing with any shade with Stainers, as required includingcleaning and smoothening surface thoroughly : (ii) External surface (Ground floor) (b) Two coats (on new works only). (i) Other than yellow, pink.

Supplying, fitting and fixing Orissa pattern water closet in white glazedvitreous chinaware of approved make in position complete excluding 'P' or'S' trap (excluding cost of concrete for fixing). (i) 580 mm X 440 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing white vitreous china best quality approvedmake wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks,C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillarcock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approvedquality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approvedquality P.V.C. connection pipe with heavy brass C.P. nut includingmending good all damages and painting the brackets with two coats ofapproved paint. (ii) 550 mm X 400 mm size

Supplying, fitting and fixing flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 Mm X 75 mm wooden blocks Complete. 470 mm X 280 mm X 340 mm

Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm

Supplying, fitting and fixing bib cock or stop cock. e) PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or 15 mm

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes 15 mm dia

20 mm dia

25 mm dia

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (ii) Double Socketed 3 Meter Length (b) 110 mm

(a) Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc.

(A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary b) On steel or other metal surface : With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)

Construction of septic tank of Different capacities as per Aproved drawing with 1st class brickwork in cement mortar (1:4) including two 560 mm RCC manhole cover (heavy type) of approved make supplied, fitted and fixed in the 100 mmthick RCC (1:1.5:3) top slab with necessary fittings 20 mm thick cement plaster ...........on the basis of actual height based on relevant IS code.

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size)including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials.With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.

Add : GST 18%

Add L W Cess 1%