Zilla Parishad Tender

Filling in foundation or plinth by Silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water ramming complete, including the cost of supply of silver sand (Payment to be made on measurements of finished quantity)

Cement Concrete with graded stone ballast (40 mm size) excluding shuttering etc. as per direction of Engineer-in-In 6:3:1 proportion.charge, complete. In 6:3:1 proportion

Brick work with 1st class bricks in cement mortar (6:1) in Foundation and Plinth

Earth work in in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm including watering and ramming etc layer by layer complete

25 mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer's specification followed by two coat of polymer based paint,

Brick work with 1st class bricks in cement mortar (6:1) in Superstructure

Ordinary Cement Concrete ( Mix 3:1.5:1) with graded stone Chips (20 mm size) excluding shuttering & reinforcement, if any as per IS 456-2000.using Stone material of Rajmahal variety

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. Tor / Mild Steel.Engieer-in-Charge.Other than SRMB/SHYAM/JSW

125 mm thick Brick work with 1st class brick in Cement Mortar (4:1). In Ground Floor

Hire and Labour Charges for shuttering with centering and necessary staging up to 4 m using approved stout props and thick hard wood planks of approved thickness with required bracings for concrete slabs, beams, columns, lintels, curved or straight including fitting, fixing and striking out after completion of works. Using 25 mm to 30 mm thick wooden shuttering as per direction of EIC, complete.

Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary. a) 20 mm thick plaster in sand cement morter (1:6)

10 mm thick plaster in sand cement morter (1:6)

15 mm thick plaster in sand cement morter (1:6)

Neat Cement punning (about 1.50 mm thick) on wall, dado

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc,including hoisting in position, straightening if required, fixing lugs in cement concrete (1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing

Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. / 4 mm thick

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing).

Supplying,fitting and fixing cast iron 'P' or 'S' trap conformimg to I.S. 3989 / 1970 and 1729 / 1964 including lead caulked joints and painting two coats to the exposed surface. (Painting to be paid seperately).

Supplying of UPVC pipes (B Type ) & fittings conforming to IS 13592-1992

Labour for fitting and fixing U.P.V.C pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes,cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work if necessary , but including the cost and fitting and fixing holder bat clamps ( any floor ) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the E.I.C

S/F/F best quality Indian make mirror 5.5 mm. thick silver red as per I.S.3438/1965 together with brass C.P. hinges

S/F/F porcelain soap tray of approved make

Supplying, fitting, fixing Aluminium domical grating

Construction of Inspect Pit of inside measurement 600 mm X 600 mm X upto 600 mm (depth) with 250 mm thick at 1st class brick work in cement mortar (6:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (6:3:1) with jhama khoa over a layer of jhama brick flat soling, 12 mm thick (4:1) cement plaster to insidewalls and out-side walls upto GL and 20 mm thick (4:1) plaster to bottom of the pit, providing necessary invert with cement concrete (4:2:1) with jhama chips as per direction, neat cement finishing to entire internal surfaces, top of the pit cover with 100 mm thick RCC slab (4:2:1) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (4:1) in all external surface of the slab & ne 560 mm dia RCC manhole cover of approved makes supplied fitted & fixed in the slab with necessary fitings, necessary earth work in excavation in all sorts of soil, filling sides of pit with earth and removing spoils after work complete in all respect. with pakur variety / TATA / SAIL / RINL

Construction of septic tank of different capacities as per approved drawing with Ist class brick work in cement mortar (4:1) including two 560 mm dia RCC manhole cover of approved make supplied, fitted and fixed in the top slab with necessary fittings, 19 mm thick cement plaster (4:1) with neat cement finish to the internal surfaces and 12 mm thick cement plaster (4:1) to outside wall upto 200 mm below GL floor finished with 25 mm hick grey artificial stone including supplying, fittings and fixing all necessary specials, fittings, SW tees, CI foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, filling up the chabmer with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring to be done with admixture of water proofing compound @ 5% by weight of cement, complete in all respect as per directionof Engineer-in- charge. / TATA/SAIL/RINL

Construction of soak gallery (600 mm X 450 mm) with two layers of jhama metal/Brick bats (38 mm to 50 mm size) 150 mm thick and 3 layers of dry brick flats in between the layers of jhama metal leaving an opening of 100 mm X 150 mm in section along the G.L. as per sketch including cutting trenches in required grade,back filling and compacting to its original G.L. etc. complete including costs of labour and materials

Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge..

Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive

White washing including cleaning and smoothening surface thoroughly. / Three coats

Priming one coat on timber, plastered or on steel or other metal surface with synthetic enamel / oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality Synthetic Enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc on the surface if necessary