Zilla Parishad Tender

DUSTBIN (RATE WILL BE FIXED AS SQOUTATION)

Try cycle van(RATE WILL BE FIXED AS SQOUTATION)

Supplying, fitting, fixing, Chain link fencing of approved quality with R.C.C posts wooden posts or iron posts by means of galvanised "C" clips to grid of horizontal strands of galvanised high tensile spring steel wire of 12 S.W.G which have to be tensioned and fixed to the vertical posts by means of galvanised special clips, bolts and nuts etc. (The rate is exclusive of the cost of posts) (I) 50 mm. x 50 mm. x 8

SEGREGATION SHED Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.a) Depth of excavation not exceeding 1,500 mm.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) a) With earth obtained from excavation of foundation

(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation withwater, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) ( 5 th corr...)

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.b) River Bazree:

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(f) 25 mm to 30 mm shuttering without staging in foundation

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size)River Bazree

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. Groundfloor(JSW/JSPL/Shyam/SRMB/SSL/BMASL/Electrosteel)

Brick work with 1st class bricks in cement mortar (6:1)a). In foundation and plinth

125 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor.

(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation withwater, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(a) 15 mm thick plaster Ground floor

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality

Supplying , fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). (i) In Roof:- a) With 0.5 mm thick sheet

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc.

INSTALLATION OF 04 NOS OF STREET LIGHTS Supply & Erection of Single Steel tubular pole of 6mt long approx wt-52.25Kg, IS CHS 80mm OD 4mm th TATA with sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x150 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt after making drilled holes etc. on pole & carriage of pole upto 1.6 Km from Store to work-site including filling up the excavated earth pit with shifted soil and ramming properly

Extra above, for providing CC (6:2:1) base block (around the pole) dimension 0.60x0.60x0.76 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) incl. providing drilled hole in pole suitable for alkathene/polythene pipe entry as directed for street light wiring

S&F single arm header assembly 300mm long 80mm dia GI pipe welded with 1.5mt long 40mm dia GI pipe and MS angle iron frame of 35x35x5mm for photovoltic panel with nece. Nuts and bolts and painting including sypply and drawing necessy PVC insulated copper wire as per approved design&drawing of the EIC.

Earthing with 50mm dia Galvanised iron pipe 3.64mm thick x3mts long and 1x4SWG GI wire (1Mts long) 13mmx80mm dia GI bolts, double nuts, double washers incl. S&F 15mm dia GI pipe protection as to GS. By TATA Medium GI pipe for soft soil.

Supply and installation of SPV MODULE Indigenously manufactured PV module should be used. The PV module should have Mono crystalline silicon solar cells and must have a certificate of testing conforming to IEC 61215 Edition II / BIS 14286 from an NABL or IECQ accredited Laboratory. The power output of the module(s) under STC should be a minimum of 75 Wp at a load voltage of 16.4 ± 0.2 V. The open circuit voltage of the PV modules under STC should be at least 21.0 Volts. The module efficiency should not be less than 12 %. The terminal box on the module should have a provision for opening it for replacing the cable, if required. A distinctive serial number starting with NSM will be engraved on the frame of the module or screen printed on the tedlar sheet of the module. TATA BP or similar make.

Supply and Fixing All in one 15W Integrated Solar Streetlight suitable for perfect solar system solution for remote & off grid locations as well as farmhouses, gardens and parks for pathway marking and community lighting. Housing in Aluminium Alloy body which makes it water & rust proof with IP65. Enclosed inside the unit Multi cell LFP Technology BATTERY Lithium Ion/Oxide 30Ah+1%, 12.8V+0.4V, Max Continuous Discharge current (w/o PCM) upto 42A, should conform to the latest BIS/ International standards which is charged by a highly effiecient mono-crystalline solar panel. The LED luminary delivers close to 120 lumens per watt and is made from the finest LEDs from Bridgelux/Oshram/Philips confirmed to BIS specificatoon. The light must have dust to drawn system to auto control the device. The Streetlight is a plug & play unit and can be very easily mounted on walls or poles via the extensions provided with the product itself. A manual ON/OFF switch has also been provided so that the light can be switched OFF when not in use for a long time.

ADD GST@18%

ADD CESS@1%