Zilla Parishad Tender

Cement Concrete with graded jhama khoa SINGLE(30mm size) excluding shuttring Iin foundation (1:3:6) N.B VARITY

Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid T 2430/1510 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 4 mm thick High Pressure Steam Cured Non Asbestos pearl designer Fibre Cement Standard Ceiling Board (Density 1500 Kg/m3) of size 595 mm X 595 mm, conforming IS 14862 & Type A Category IV of ISO 8336, tested as per AS-1530 part 3 & BS-476 Part 4,5,6,7 & 8, should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge. In ground floor. In Foundation & plinth up to PL

Hire and labour charges for shoring work (includingnecessary clos plank walling, framing,Eucalyptus/Jhou bulla piling, strutting etc) completeas per direction of the Engineer-in-charge forfoundation excavation (vertical surface are in contactwith supported earth is to be measured.) (This itemshould be executed on specific direction of the Enginner in charge). Foundation upto plinth

Hire and labour charges for shoring work (includingnecessary clos plank walling, framing,Eucalyptus/Jhou bulla piling, strutting etc) completeas per direction of the Engineer-in-charge forfoundation excavation (vertical surface are in contactwith supported earth is to be measured.) (This itemshould be executed on specific direction of the Enginner in charge). Shuttring For coulmn,Beam,Chajja,slab For Coulmn Side Lintrel SLAB Chajja for Window

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mmnominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.I. SAIL/ TATA/RINL 1.2% of the total concrete vol.

Brick work with 1st class brick in cement morter (1:4)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excludingcost of chipping over concrete surface] 15mm thick outside plaster with cement mortar 1:6 For Ground floor

Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excludingcost of chipping over concrete surface] 20mm thick outside plaster with cement mortar 1:6 For Ground floor

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum shouldbe correted upto three decimals). h) Neem, Jam, Jackfruits

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made) iv) 25mm thick shutters with 12mm thick panel of size 30 to 45 cm. b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) a) 40mm X 6mm, 250mm Length

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) c) 40mm X 6mm, 125mm Length

Iron butt hinges of approved quality fitted and fixed with steel crews, with SI (vii) 100mm. X 58mm. X 1.90mm.

Iron parliamentary hinges conforming to IS 362-1982 fitted and fixed complete with steel screws. (d) 225mm long x 10mm dia bolt.(for door)

Iron parliamentary hinges conforming to IS 362-1982 fitted and fixed complete with steel screws. (d) 150mm long x 10mm dia bolt.(window)

i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting.

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) Quantity same as the inside + celling plaster Quantity (LS)DETAILS IN BILL

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (GROUND FLOOR)(LS)DETAILS IN BILL

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats GF(LS)DETAILS IN BILL

B) Painting with superior quality aluminium paint of approved make and brand including smoothening surface by sand papering etc. on steel surface :

Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. (a) Area of each tile upto 0.09 Sq.m

Supplying and laying true to line and level vitrified tiles ofapproved brand (size not less than 600 mm X 600 mm X 10mm thick) in floor, skirting etc. set20mmsandcementmortar (1:4) and 2 mm thick cement slurry back side of tilesusing cement @ 2.91Kg./sqM or using polymerised adhesive(6 mm thick layer applied directly over finished artificial stonefloor/Mosaic etc ofcement per sqM belowmortar only, joints grouted with admixture of white cementand colouring pigment to match with colour of tiles / epoxygrout materials of approved make as directed and removal ofwax coating of top surface of tiles with warm water andpolishing the tiles using soft and dry cloth upto mirror finishcomplete including the cost of materials, labour and all other incidental charges complete true to the manufacturer'sspecification and direction of Engineer-in-Charge. (Whitecement, synthetic adhesive and grout material to be suppliedby the contrr]e)ILS IN BILL (I) With application slurry @1.75 kg/ Sq.m, 20 mm sandcement mortar (1:4) & 2 mm thick cement slurry at back sideof tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.(B) Light Colour

ELECTRICITY 20 %

SANITATION 10 %

Dismantling all types of plain cement concreteworks, stacking serviceable materials at site andremoving rubbish as directed within a lead of 75M (a) upto 150 mm. thick (LS)

Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (b) 4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating) Diduction (Glass Portion)

Labour charge for fabrication and installation of structural Glazing/Curtain Wall made from annodized extruded allooy aluminium sections for the following units:- Structural Glazing made of extruded and annodized alloy aluminium sections, fabrications including cutting to proper shape and size, drilling including cost of brackets, fastener bolt, mullion bolt, nuts & washers, maskin tape, double side adhesieve crosslink foam (used for guard of glazed silicon on sub-frame), tissue paper foam (used as filler between sub-frame and under backing of weather silicon), screws and other necessary hardwares, fixing of glass as per drawing, specification and direction of Engineer-in-Charge. (The rate includes hire charges of all tools and plants, including all incidental charges, adhesieve, joiners such as screw,cleate angle,etc. but excluded the cost of extruded aluminium sections, glass, glazed silicon, weather silicon etc.) c) 40mm X 6mm, 125mm Length

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In Charge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film G) Fixed Glazing.i) Top, bottom and side member. (LS)

Supplying Weather Silicone sealant of approved make and brand for fixing of grove line between the Glasses as per direction of Engineer-in charge. for Structural Glazing/Curtain wall.Weather Silicone sealant for filling the Grove line between Glasses or any other material for facial work

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987; (A) clear, toughened glass conforming to IS: 2553-1992 (part-II) vi) 6mm thick coloured / tinted / smoke glass.

(a) M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windowsrailing etc. fitted and fixed with necessary screws and lugs in ground floor (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

M.S structural works with hollow section ( square or rectangular shape) confroming to is : 806-1968 & IS : 1161-1998) connected to one another with bracket,gusset, Cleat as per design, Drwaing & direction of engineer-in-charge complete including cutting to request shape & size, fabrication including metal are wedlding confroming to IS : 816-1969 &IS : 9595 using electrodes of approved make and brand conforming to IS : 814-2004, haulage, hosting and erection all complete. Payment to be madeon the besis of calculating weight of structural members of MS hollow section as specified in relevent IS code in finished work payment for guesst, bracket cleatmay be made by adding the actual weight of such items with weight of finished structural members.therates are considerd for a hight of finished structural members. the rates are considerd for a hight og erection 8m / 2nd floor level from the ground add 1.5 % extra over the rate for each additional floor or 4m. beyond 8m or part thereof

Galvanised corrugated iron sheet work (excluding thesupporting frame work) fitted and fixed with 10 mm. dia J orL hook-bolts, limpet and bitumen washers and putty completewith 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet tobe supplied by contractor)i) 60 MM THICK

DISPLEY BOARD

Add:- GST @ 18%

Add:- Labour Welfare Cess @ 1%