West Bengal State Marketing Board Tender

Supplying & laying Polythene sheet (150 gm/Sq. m ) over damp proof coarse or below flooring or roof tarracing or in foundation or foundation trenches.

Cement Concrete with 40 mm down ballast excluding shuttering. (1:3:6 proportion.)( Pakur Vr.)

Brick work with 1st class bricks in cement mortar (6:1) (a) Foundation and Plinth

Brick work with 1st class bricks in cement mortar (6:1) b)        In Superstructure

125mm. thickbrickworkwith1st class bricks incementmortar (1:4) in ground floor.

Ordinary Cement Concrete (mix 1:1.5:3) with graded stone chips 20mm. nominal sizes excluding shuttering and reinforcement (if any) as per relavent IS Code . (i) Pakur Vr.

Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hardwood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting fixing and striking out after complete of works(upto roof of groun floor). f) 25mm to 30mm shuttering without staging in foundation.

(i) Reinforcement for reinforced concrete work in all sorts of structure including distributors, stirrups binder etc. including supply of rods initial straightening and removal of loose rust ( if any) necessary cutting to requisite length hooking and bending to correct shape placing in proper position every intersection complete as per drawing and direction. For works in foundation, basement, roof of ground floor/upto 4m. i) Tor Steel II) Other than Sail/TATA/RINL

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (i)(c)15mm th. Cement plaster(1:6)

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (ii)(b)15mm th. Cement plaster(1:4)

Plaster (to wall, floor, ceiling etc.)with sand and cement mortar including rounding off corners and chamfering corners as directed and racking out including, throating, nosing and drip coarse, scafolding/ staging where necessary(Ground Floor) (Excluding cost of chipping over concrete surface.) (ii)(c)10mm th. Cement plaster(1:4)

Neat cement punning 1.5mm thick in wall dado window silt, floor, drqins etc. using cement @ 0.152Cum/M2

Applying decorative Cement base paint ofapproved quantity after scraping the surfacethroughly as necessary as on plastered surfasce, ruled or concrete surface. Two coats

Applying exterior grade acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured (matt finish) or smooth finish / Acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacture's specification and as per direction of EIC. (b) two coats

Protective and decorative textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystaline additives derived from granite as per manufacture's specification and as per direction of EIC to be applied over acrylic primer as required.( Two Coats )

Supplying, fitting & fixing 1st quality Ceramic tiles inwalls and floors to match with the existing work & 4nos. of key stones (10mm) fixed witharalditeat the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2mm thick cement slurry at back side of tiles using cement @ 2.91 kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

Supplying, fitting & fixing 1st quality Ceramic tiles inwalls and floors to match with the existing work & 4nos. of key stones (10mm) fixed witharalditeat the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc (B) Wall WithSandCementMortar (1:3) 15mmthick&2mmthick cement slurry at back side of tiles using cement@2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (ii) Other than Coloured decorative including white

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand Papering.

(b)Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

Painting with superior synthetic enamel paint of approved made and brand including smoothening the surface by sand paper. i) on steel

Painting with superior synthetic enamel paint of approved made and brand including smoothening the surface by sand paper. (a) On timber or plastered surface : With other than hi-gloss of approved quality (iv) Two coats (with any shade except white)

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to I.S. 1038-1975 and manufactured from rolled steel section conforming to I.S7452-1974 with non friction projecting type box type type hinges. b) Openable steel window with side hung shutters.

Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to I.S. 1038-1975 and manufactured from rolled steel section conforming to I.S7452-1974 with non friction projecting type box type type hinges. c) (viii)Extra over above item for- M.S. Integretd grill as approved design integreted with steel window or ventilator.

Supplying fitting fixing in position fibre glass panes of approved quality with resin. Nail, clip etc. as IS: 12866-1989. in all floor internal wall) (e) 4 mm thick.

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all ecessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. ii) 110 dia

M.S. structural works with hollow sections (TATA make square or rectangular shape) conforming to IS: 806-1957 & IS:1161-1958) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1956 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.

Supplying, fitting & fixing Zn-Al alloy coated (Followed by colour coated )steel sheet work having minimum Yield strength of 550 Mpa of Trapizoidal profile of approved make (excluding the Suporting frame works) fitted and fixed with 10mm dia 'J' or "L' hook bolts limpet and bitumen washers and putty complete with 150mm end lap and one orrugation minimum side lap.( Payment to be made on area of finished work)

Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. (i) 16 mm dia bolt i) 300 mtr

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings ((a) 35mm thick shutters (single leaf)

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (d) Sal : Local

Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish)made of extruded P.V.C. multichamber hollow section having dimensions 60mm x50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner/wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials, taxes and all other incidental charges complete

PVC Door Shutter-30 mm thick:Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular 'L' shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete.

M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The boards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete)

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. (i) For 10 users A) With Pakur variety. (other than SAIL/TATA/RINL)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.( other than SAIL/TATA/RINL)

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. White

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc a) With 'P' trap

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (ii) Plastic (hallow type) white

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) i) 15mm dia

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) ii) 20mm dia

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) iii) 25mm dia

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (A) (i) Single Socketed 3 Meter Length

Supplying, fitting and fixing shower of approved brand and make. (a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model Tropical / Sumthing Special of ESSCO or similar brand)

Supplying, fitting and fixing bib cock or stop cock a) (ii) Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model- Tropical / Sumthing Special of ESSCO or similar brand)

Supplying, fitting and fixing bib cock or stop cock (b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model- Tropical / Sumthing Special of ESSCO or similar

Supplying, fitting and fixing bib cock or stop cock (d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).