West Bengal State Electricity Distribution Company Limited Tender

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or rougening of concrete surface, including throating, nosing and drip course where necessary. ( excluding cost of chipping over concrete surface ). With 1:6 cement mortar 20 mm. thick plaster In Ground floor.

15 mm. thick plaster In Ground floor.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface. With other than Hi-gloss of approved quality. Two coats (with any shade except white)

Applying Exterior grade Acrylic Primer of approved quality and brand on plastered or concrete surface (old or new) to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly,complete as per manufacturer's specification and as per direction of the EIC. In ground floor. One coats.

Protective and decorative Acrylic exterior Emulsion paint of approved quality,as per manufacturer's specification & as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In ground Floor (Two Coat ).Super Protective 100% Acrylic Emulsion.

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacture's specification) including cleaning and smoothning surface. Two coats.

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.A) Floor. With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m.(i) Coloured decorative.

Ordinary Cement Concrete( mix.1:2:4) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement, if any, as per relevant I.S.Codes Pakur variety.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups,binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. Tor steel/Mild steel (SAIL/TATA/RINL) For works in foundation, basement and upto roof of ground floor / upto 4m.

Ordinary Cement Concrete( mix.1:1.5:3) with graded stone chips(20 mm.nominal size) excluding shuttering and reinforcement if any,in ground floor as per relevantI.S.Codes Pakur variety. In ground floor.

25 mm. to 30 mm. thick wooden shuttering without staging in foundation.

Supplying, fitting and fixing bib cock or stop cock. Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

Chromium plated Bib Cock with wall flange (Equivalent to Code No.5047 & Model - Florentine of Jaquar or similar brand.

Supplying, fitting & Fixing approved brand PVC connector white flexible with both ends coupling with heavy brass C P nut 15 mm dia. 600 mm long.

Supplying, fitting & Fixing 32 mm dia PVC waste pipe with PVC Coupling at one end fitted with necessary clamps. 1050 mm long

Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. The rate includes the hire charge of all tools and plants, adhesive, joineries such as screw, cleate angle etc. but excluded the cost of extruded alumium sections, glass,panel boards neoprene / EPDM gasketing, locking arrangement, weather gasketing / wool pile, floor spring, top pin, handle, tower bolt, glazing clips etc. (10% rate reduction has to be made for swing doors or partitions where floor sping is not used. 10% enhancement of rate is to be made where door frame of extruded aluminium sections has to be fitted and fixed to masonry wall. 5% rate enhencement may be allowed for double leaf swing door. Payment shall be made for the shutter area only exept where door frame is fixed the entire opening shall be taken to consideration. Payment for door frame sections are to be paid seperately).

M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr