West Bengal Electronics Industry Development Corporation Limited Tender

Cleaning the exposed corroded Reinforcement as well as worn out concrete by sand blasting with air compressor including all materials, hire charges of machineries and labour etc. all complete as per technical specification and direction of the Engineer-in-Charge.

Providing anti-corrosive protective coating to inhibit the corrosion to HYSD reinforcements including two coats of anti-corrosive coatings of consumption as per manufacturer's specification, cleaning etc. complete as per the direction of the Engineer-inCharge

Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m. including stacking of steel bars. All floor & any Height

Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineerin- Charge prior to execution will be necessary).

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, leveling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1,500 mm.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, leveling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring.

Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm. Including watering and ramming etc. layer by layer complete. (payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation.

Earth work in filling in compound, tank, low land, ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement before and after the work. With carried earth arranged by the contractorany lead. including cost of carried earth.

Filling in foundation or plinth by yellow fine sand (Grading Zone III as per IS: 383-1970) stacked at site.) in layers not exceeding 150mm as directed & consoling the same by through saturation with water ramming complete including the cost of supply of sand (Payment to be made on measurement of finished quantity)

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Antitermite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrefos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 liter per sq.m. of the surface before sand bed or subgrade is laid. Holes upto 50mm.to 75mm. deep at 150mm. centre to centre both ways shall be made with 12mm. diameter mild steel rod on the surface to facilitated saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in Para 6.4 of code IS-6313 (Part-II)-1981. (Mode of measurement will be per sq.m. of plan area of plinth treated).

Hire and labour charges for shuttering with centering . using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. 25 mm to 30 mm shuttering without staging in foundation

Hire and labour charges for shuttering with centering and necessary staging upto 4 m. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. Steel shuttering or 9 to 12 mm thk. Approved quality ply board shuttering in any concrete work. All floor, Roof & above

Supplying & laying Polythene sheet (150gm/sqm.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. All floor, Roof & above

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. foundation, basement all floor, Roof & above

Cement concrete with graded stone chips(20mm nominal size) any floor 1:3:6 proportion. foundation, basement all floor, Roof & above

Batch Mixed concrete of M 25 Grade with well Graded stone chips of 20 mm nominal size containing designed quantity of cement per Cu. M of Wet concrete produced in computerised batching plant under controlled condition using approved super plasticizer designing concrete mix following I.S 10262 and I.S. 456 transporting the mix with agitation in transit mixer to work site depositing the mix on a platform erected for the purpose at required level of concreting and then placing the mix in its final location of form work compacting and curing the same complete as per specification and direction of the Engineer-in charge including hire charges of computerised batching plant, transit mixer with all accessories vibrators etc. inclusive of all other incidental charges in this connection complete but excluding cost of hire charge of platform and its supporting staging which would be paid through separate item. Consumption of cement will not be less than 300 Kg of cement per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. foundation, basement all floor, Roof & above

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For work in foundation, basement all floor, Roof & above. Tor steel Fe 500 (SAIL/TATA/RINL).

Ordinary cement concrete (mix1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering & reinforcement if any, in ground floor as per relevent IS codes. Pakur variety. Foundation, basement all floor, Roof & above

Brick soling with picked jhama bricks including preparetion of bed as necessary with joints properly filled in and packed with powdered earth and including necessary cushion of similar material below the soling (and in between layers when more than one layer is used) completes as per direction. Single brick flat soling(thickness 75mm.). Foundation, basement all floor, Roof & above

25mm thk Damp Proof Course with cement concrete (1:1.5:3) (with graded stone aggregate 10mm normal size) & painting the top suface with a coat of bitumen [ VG 40] using 1.7kg. Per Sqm. Including heating the bitumen & cost & carriage of all materials complete. [ Bitumen to be supplied by the Agency]. Foundation, basement all floor, Roof & above

Brick work with 1st class bricks in cement mortar(1:4). In foundation and plinth

Brick work with 1st class bricks in cement mortar(1:6) . In Superstructure , Foundation, basement all floor, Roof & above.

125mm thk. Brick work with 1st class bricks in cement mortar (1:4) in ground floor. Foundation, basement all floor, Roof & above

75 mm thick brick work with 1st class Bricks set in cement, sand mortar(1:4) in ground floor including H.B. netting in very alternate layers. Foundation, basement all floor, Roof & above.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, noisng and dripourse, chiping, scaffolding / staging where necessary. With 1:6 cement mortar. 20 mm thick plaster. Foundation, basement, all floor, Roof & above.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, noisng and dripourse, chiping, scaffolding / staging where necessary. With 1:6 cement mortar. 15 mm thick plaster. all floor, Roof & above.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, noisng and dripourse, chiping, scaffolding / staging where necessary. . With 1:4 cement mortar. 10 mm thick plaster. all floor, Roof & above.

Providing, mixing and laying protection for plaster work admixed with surface active plasticising agents, polymers & additives. (conforming IS 2645 2003 & IS: 9103-2000) at 200 ml per bag of cement all in complete. all floor, Roof & above.

Chipping of concrete surface before taking up Plastering work (including cost of all tools, labour, scaffolding & other initial charges). Thls work should not be excuted without specific permission of Engineer-in-charge. Complete in all respect all floor roof & above.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips laid in panels as directed with topping made with ordinary or white cement (as necessary) & marble dust in proportion (1:2) including smooth finishing & rounding off corners including raking out joints or roughening of concrete surface & application of cement slurry before flooring works using cement @1.75kg/sqm all complete including all materials & labour. In ground floor. 3mm thick topping(High polishing grinding on this item is not permitted with ordinary cement). Using grey cement. 25mm thk. all floor, Roof & above.

Supplying, fitting and fixing 18 mm. to 22 mm. thick kota stone slab in wall, Stair, dado in 15mm thick [avg] cement mortar (1:3) including making suitable arrangement to hold the stone properly by brass / copper hooks including pointing in cement mortar (1:2) (1 cement : 2 marble dust) with admixture of pigments matching the stone shade, including grinding and polishing all complete as per direction of Engineer-in-charge including cost of materials, labour, scaffolding, staging, curing complete. [Using cement slurry for bedding @4.4 kg/Sq.m and for jointing @1.8 kg/Sq.m]. all floor, Roof & above.

Toilet Floor: Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622- 2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance 0.5, Mohr's hardness 5.0, Staining resistance: Class-1, Water Absorption: E 0.5%], MOR 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). In Ground Floor: Sizes-300 mm x300mm x10 mm with breaking strength 1200 N. all floor, Roof & above.

Supplying , fitting & fixing 1st quality Ceramic tiles in walls to match with the existing work & 4 nos. of key stones (10 mm.)fixed with araldite at back of each tiles & finishing the joints with the white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface ,if necessary or by synthetic adhesive & grout materials etc. (Anti skid) with sand cement mortar (1:3) 15mm thick & 2mm thick cement slurry at back side of tiles using cement @ 2.91 kg/Sqm. & joint filling using white cement slurry @0.20kg./Sqm. Area of each tile above 0.09sqm. colour decorative. all floor, Roof & above.

Supplying , fitting & fixing anti skid or Digital glazed 1st quality Ceramic tiles (Size-600mm X 600mm X minimum 8-10mm thick) ) in floors and dado to match with the existing work & 4 nos. of key stones (10 mm.)fixed with araldite at back of each tiles & finishing the joints with the white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface ,if necessary or by synthetic adhesive & grout materials etc. Floor With Polymerised and epoxy grout pointing including spacer-2mm ( When Tiles are laid over existing hard ready surface). Area of each tile (Size 600mmx600mm) above 0.09sqm. Colour Decorative in any floors. Roof & above.

Neat Cement punning about 1.5mm thick in wall dado, window sills floor, drain Note: cement 0.152cum. Per 100sqm

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). sal: malayasian. any floors. Roof & above.

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative natural veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: 35mm thick shutters (single leaf).any floors. Roof & above. inlcuidng cost of PU Polish over veneer surface

Supplying fitting & fixing fiber reinforcement polymer(FRP) composite door shutters as per approved design with glass fiber reinforcement plastic moulded skins & a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science & Technology(DST) to satisfy IS:4020 door testing performance criteria. any floors. Roof & above. 32mm thick

Supplying fitting & fixing fiber reinforcement polymer(FRP) composite door frame as per approved design with glass fiber reinforcement plastic moulded skins & a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science & Technology(DST) to satisfy IS:4020 door testing performance criteria. 66mmx90mm. Any floors. Roof & above.

Supplying, Fitting & Fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. In cement concrete(1:2:4) including cutting of brick work / concrete work as per direction. 40mmx6mm,200mm length. Any floors. Roof & above.

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :125x64x2.5 mm. Any floors. Roof & above.

Supplying, fitting & fixing SS floor door stopper. Any floors. Roof & above.

Providing and fixing bright /matt finished decorative Stainless Steel handles of approved quality & make with necessary screws etc all complete - 250 mm. complete in all respect. All floor, roof & above

Anodised aluminium aldrop/sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted & fixed complete. 250mm x 16mm dia bolt. Any floors. Roof & above.

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: . 100mm long x10mm dia bolt. Any floors. Roof & above.

Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete-125mm. All floor & roof

Supplying fitting & fixing 6 levers Crystal Satine Mortice Lock or pin cylinder technology with pair of lever handle and keys including fitting & fixing complete. Any floors. Roof & above. of approved make as per selection by customer

Supplying fitting & fixing Hydraulic door closer fitted and fixed complete. Heavy type. Any floors. Roof & above.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge ( Including Door handle, lock and stopper etc.).

Supplying fitting & fixing of full Height frameless 12 mm thick clear or Frosted glass toughened glass interior partition. Product should be manufacturing as per specifications given below: All aluminium or parts section made from (aluminium alloy 63400-WP or IS: 733 & IS 1285:2002) shall undergo a 8-10 stages anti rust treatment and shall be powder coated with Epoxy polyester in Glossy finish to a thickness of 60 to 70 microns. The frame structure is made by joining different Extrusions (Refer Assembly guide lines for Sections details) by means of brackets made of 3 mm Thk HR (IS-2062) and screws as per elevations defined by client. All the stainless steel (Grade 304) & all hardware fitting as per I.S.I standards. All glass partition 12 mm thick clear toughened glass (IS-2835) partitions shall be mounted on floor gaskets made of rubber / PVC to provide gripping with the floors. PVC Rubber extrusion fixed on to the extrusion profile, supports the glass edges from back Side. Each frame shall be provided with minimum two or more 12mm levelling bolts which allow 40 to 50mm adjustment for floor unevenness as well as false ceiling height difference (up to 15 mm). The levellers shall be concealed inside the skirting. All the exposed partition paned edges shall be fixed with aluminium extrude box shape powder coated trims. Ends must be covered with Die cast aluminium. The rate shall include all design, support (if required). Including the cost of glass, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel etc. complete in all respect. All floors & roof. (Mode of measurement: The above Glass partition will be measure the single side exposed surface area.)

Providing, fitting and fixing in position glazed casement/ 2trake or sliding windows and casement or fixed type windows, skylights ventilators with 6mm thick float/smoke glass in natural mat finish anodised colur (10-12 micron) aluminium section of series 40 mitre and jointed crimped with stainless steel friction stay, handles, locks, glazing clips, EPDM gasket, weather pile in frame grooves, nickel chrome plated fixing screws all of approved make including all materials and labour asper drawings, specifications complete. Any floors. Roof & above.

Supplying, fitting & fixing two pointed nose aluminium handle including fitting & fixing. any floors. Roof & above.

Supplying, fitting & fixing Aluminium peg stay 300mm long including fitting fixings

Supplying fitting & fixing with integrated grills conforming to IS 1038-1975 & manufactured from rolled or Square steel sections conforming to IS 7452-1974 with non-fricition projecting type, box type hinges, glazing clips, lugs locking bracket, handle plate etc. including hoisting in position, straightening if required, fixing lugs in cement concerete (1:2:4) with stone chips 20mm down cutting holes & mending good damages to match with excluding glazing . M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continously welded with M.S. flats & bars. any floors. Roof & above.

Suplying fitting & fixing Collapsible gate with 40mm x 40mm x 6mm tee as top & bottom guide rail, 200x10mmx2mm vertical channels 100mmapart in fully stretched position 20mmx5mm M.S. flats as collapsible bracings properly rivetted & washered including 38mm steel rollers including locking arrangements fitted & fixed in position with lugs set in cement concrete & including cutting necessary holes chasing etc. in walls floors etc & making good damages complete etc. any floors. Roof & above.

Suplying fitting & fixing M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. Grill weighing above 16 Kg./sq.mtr and above. any floors. Roof & above.

Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three ) nos 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade) Brushed/Mat finish, complete as per direction of the Engineer-in-charge. Weight of Strainless Steel railing per metre 6.5 Kg (approx). any floors. Roof & above.

Supplying and applying Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including surface by sand papering etc. any floors. Roof & above.

Supplying and Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. any floors. Roof & above.

Supplying and applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. Two Coat. any floors. Roof & above.

Supplying, and, applying protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Two Coats. Super Protective 100% Acrylic Emulsion. any floors. Roof & above.

Supplying,applying rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick). The rate includes cost of material, labour, scaffolding and all incidental charges. any floors. Roof & above.

Supplying, and, applying Interior grade Acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. Solvent based interior grade Acrylic Primer. any floors. Roof & above.

Supplying & Applying acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : Two Coats. Luxury Quality. The rate includes cost of material, labour, scaffolding and all incidental charges. any floors. Roof & above.

Supplying & Applying painting with best quality synthetic enamal paint of approved make & brand including smoothening surface by papering etc. including using of approved putty etc. on the surface, if necessary: on timber or plaster surface. With super gloss (hi gloss). Two coats (with any shade except white). any floors. Roof & above.

Supplying & Applying painting with best quality synthetic enamal paint of approved make & brand including smoothening surface by papering etc. including using of approved putty etc. on the surface, if necessary: On steel or other metal surface: With super gloss (hi-gloss). Two coat (white in shad). any floors. Roof & above.

Supplying & Applying protective and Decorative Textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystalline additives derive from Granite as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. any floors, roof & above.

Supplying, fitting & fixing bubble free float glass of approved make and brand conforming to IS: 2835-1987. 5mm thick coloured / tinted / smoke glass. any floors, roof & above.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 12mm thick cleared toughened glass coforming to IS: 2553-1992 (Part-II)

Supplying and laying true to line and level 25 mm. thick precast roof tiles made of cement conc. With stone chips as per approved strength and density set in 25 mm.(Avg) thick cement morter (1:3) & filling up joint (3mm wide) with cement sand mortar (1:1) applying cement slurry @ 1.75 kg. per Sqm. back of tiles & then setting close the precast tiles, finishing up the joints with slurry already laid & finally finishing the top surface including providing 150mm high skirting with the top surfac including providing 150mm high skirting with the same tiles flushed with the inside surface of parapet wall finishinbg the mouth of rain water pipes, curving etc. as necessary complete as per direction of the Engineer- in- charge.(levelling if necessary maybe paid separately).For 25mm thick precast tiles (cement 14.6kg./Sqm. Underlayer). any floors, roof & above.

Supplying & applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required). any floors, roof & above.

Supplying & laying Polymer concrete made with water resistant bonding agent of synthetic rubber emulsion as per manufacturer's specification including the cost of cement concrete (2.75 Kg / bag of cement) Note : Payment on volume of (1 : 1½ : 3) Concrete. any floors, roof & above.

Supplying & providing surface preparation by mechanical means to remove any dust , laitance, oil, grease and any other foreign material and ensuring the surface dampness by water ponding test all in complete. any floors, roof & above.

Providing and laying protection plaster (12-15 mm) in 1:3 ratio (cement:sand) admixed with Dr Fixit Pidiproof LW plus (conforming IS 2645 2003) at 200 ml per bag of cement all in complete. any floors, roof & above.

Supplying & applying glass Fibre mesh- Used for angular filleting purpose at wall slab junctionSupplying Bathseal system over the sunken portion floor of bathroom, with the products in the ‘Kit’ as detailed below : a) Bathseal Tape - Bituminous two sided adhesive tape for wrapping around pipes inserted through wall and floor.b) Bathseal Grout - Non-shrink expansive, cementitious free flowing grout for filling gaps around bathroom pipes to fill in the gaps besides pipes. c) Bathseal WPC - Acrylic elastomeric cementitious waterproof coating for sunken portion and wherever required.. d) Pidicrete URP - To prepare mortar with it to fill in the external side walls gaps etc. e) Glass Fibre mesh- Used for angular filleting purpose at wall slab junctionApplication oft Bathseal system After water-testing cementicious pressure grouting could be done, if felt required and wherever required only. For grouting, holes should be drilled at 45⁰ angles around the ½ of thickness, of the structure and cementitious slurry to be injected through the fixed nozzles, wherever required, by applying adequate pressure. Providing and laying of fillets at the junction of slab and vertical walls prepared with cement sand mortar in the ratio 1:5 admixed with 5-7% of Pidicrete URP by weight of cement. (Cement, sand will be supplied by client at fee of cost)Applying Bathseal system over the sunken portion floor of bathroom, with the products in the ‘Kit’ as detailed below : a) Bathseal Tape - Bituminous two sided adhesive tape for wrapping around pipes inserted through wall and floor. b) Bathseal Grout - Non-shrink expansive, cementitious free flowing grout for filling gaps around bathroom pipes to fill in the gaps besides pipes. c) Bathseal WPC - Acrylic elastomeric cementitious waterproof coating for sunken portion and walls in bathroom. d) Pidicrete URP - To prepare mortar with it. e) Glass Fibre mesh- Used for angular filleting purpose at wall slab junction. any floors, roof & above.

Supplying, fitting & fixing fire resistant door frame conforming to IS:3614, tested and certified as per laboratory approved by Engineerin-charge, of section 143 x 57 mm having built in rebate made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 120 minutes fire rated door shutters. The frame is fitted with intumescent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with back plate bracket and anchor fastener of approved size and make. Rubber door silencers should be provided on striking jamb.

Supplying, fitting & fixing fire resistant Door leaf of 46 mm thick fully flush double skin glazed fire resistant door shutters with or without vision lite, of 120 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 18 SWG G.I. sheet (zinc coating not less than 120 gm/ m2) duly filled heat-resistant phenolic resin bonded insulation material (honeycomb craft) and fixing with necessary stainless steel ball bearing hinges of approved make. For pair of doors astragals has to be provided on the meeting stile for both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturer recommendation with a beeding and screw from inside. The glass should be 6mm clear borosilicate fire rated glass of relevant rating. All door and frames shall be finished with polyurethene aliphatic grade paint of approved colour including applying a coat of approved brand fire resistant primer. The door leaf and frame shall have passed minimum 250 hours of salt spray test. Rate should include supply and installation complete as per direction of Engineerin-charge. 2 hour Fire rated door single leaf of size (1200 mm x 2180 mm)

Supplying wooden moulding slanting beat of size 37mm X 18mm (finished) of approved design to finish the joint between wooden frame of door/window with masonary in true line and level fitted & fixed with adhesive and head less pins complete as per direction of Engineer -in-charge. Teak wood beat

Supplying applying & Drilling holes along the construction joint at 500 cm/cc and fixing PVC nozzles of 12 mm dia with suitable quick set compound and injecting cement slurry admixed with non shrink grouting compound ( Dr Fixit Pidicrete AM ) at 225 gm per bag of cement at 3-4 kg/cm2 pressure till refusal. any floors, roof & above.

Supplying applying Cutting grooves along the construction joint areas in 50 mm X 50mm & sealing the same using polymer modified mortar in 1:3 (cement:sand) ratio applying Dr Fixit Pidicrete URP (SBR based polymeric resin) by 5% weight of cement.Waterproofing coating- Providing and applying two coats of Dr Fixit Pidifin 2K (High performance polymer modified cementitious coating) by brush/ roller on the SSD surface sand witched with 45 gsm geofabric membrane and it will be terminated up to 300 mm onthe wall. Inter coating time interval will be maintained between 3-4 hours and sieved sand will be sprinkled on the top coat in tacky condition all in complete. The consumption of waterproofing coating should be minimum 1.5 kg/sqm to ensure the total thickness of 1 mm including geofabric. The product should conform the elongation of 40% as per ASTM D412, hardness of minimum 80 shore A as per ASTM D2240, and adhesion strength of minimum 0.5 N/mm2 as per ASTM D 412. any floors, roof & above.

Providing and fixing bottom shuttering (wooden/metal) from the bottom level of the pipe penetration area Cleaning the pipe penetration areas to ensure the surface free from dust, laitance, oil grease any other foreign material and applying one coat of cement slurry admixed with Dr Fixit Pidicrete URP (SBR latex) by 12%-15% by weight of cement by brush, as a old to new concrete bonding agent and allow the surface in tacky condition.Filling the gaps around the pipe penetration area using 10mm down chips aggregate and cement, sand in 1:1.5:3 either 1:2:4 ratios, ensuring a gap / grouting height of 50 mm height from the top of the pipe opening surface. Providing and laying Dr Fixit Pidigrout 10M (non shrink free flow cmentitious grout) maintaining water powder ratio 0.13-0.15 as per manufacturer’s specification /TDS. Cure the grouted surface for minimum 3 daysPrepare a groove of 10 mm X 10mm around the top of the pipe penetration area and sealing the gap will be done using Mseal sanitary ( 2 part epoxy sealant, to be mixed in 1:1 ratio by volume/weight). any floors, roof & above.

Supplying & provide chicken mesh in joints of R.C.C. & brickwork before plastering.All floor and above roof.

Making V-groove line ( 12 mm wide,12 mm deep) in plastered surface or as per direction of Engineer in Charge.

Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface).

Supplying and application of chemical for post Installed rebar connection by using ETA approved for seismic criteria In rebar connection, Including drilling hole to the required depth by rotary hammer drill, cleonlng with brush & jet of clean air, /filling chemical(HIT-RE 500 or equivalant) using serrated nozzle to eliminate mIxIng error and in a voldless manner IncludIng charges for all tools & plants. Application to be designed for post· Installed rebars as per ECZ / TR023 or relevant tested and accepted design guidelines and the design document to be furnished by the manufacturer. The chemical should have ETA apprOVal for seIsmIc criteria of rebar fixing whIch should be furnished by manufacturer. The installation and the setting instructions should be strIctly followed as per manufacturer's specl/icatlons as approved by EICprior to drlll/ng along with post· Installed rebar embedment design report. The existing concrete member should be scanned using rebar scanner to avoid hitting existing reinforcement in concrete during drilling. complete in all respect & all floor, Roof & above.

Cost of post installed rebaring application with chemical as speclfled for 8 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 10 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 12 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 16 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 20 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 25 mm dia per cm of depth

Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface).

BOQ Sanitary & Plumbing Works

Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.).

25 mm

20 mm

32 mm

40 mm

50 mm

Supplying, fitting and fixing Chromium plated Bib Cock with wall flange (Equivalent to Code No.5047 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand).

Supplying, fitting and fixing pillar cock of approved make CP Pillar Cock with 200 mm extended Lever Handle (Equivalent to Code No. 5031 & Model - FLORENTINE of JAQUAR or similar brand).

Supplying, fitting and fixing pillar cock of approved make CP Wall Mixture without spout but with provision for connnection to Telephone Shower and exposed pipe for Overhead shower (Equivalent to Code No. 5215 & Model - FLORENTINE of JAQUAR or similar brand).

Supplying, fitting & fixing CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No.5041 & Model - FLORENTINE of JAQUAR or similar brand

Supplying, fitting & fixing as per specification drawing & direction Towel rack Complete in all respect.

Supplying, fitting & fixing as per specification drawing & direction Towel ring Complete in all respect.

Supplying, fitting & fixing Chromium plated double coat Hook(Equivalent to Code No. 35761 & Model - KUBIX of Jaquar or similar).

Supplying, fitting & fixing as per specification drawing & direction C.P Gravity 125 dia Complete in all respect.

Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO /ATLAS or equivalent. 15 mm

Supplying, fitting and fixing complete Bottle waste trap (Heavy Quality) Chromium plated Bottle trap 32 mm with 190 mm long connecting pipe and wall flange (Equivalent to Code No. 545 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

Supplying, fitting and fixing C.I. holder bat clamp including cutting holes in wall etc. and mending good all damages in cement concrete with jhama chips (4:2:1) and cement plaster (6:1) to match and curing complete in all respect.

20 mm

25 mm

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. For Exposed Work CPVC Pipes Class-I,SDR-11

20 mm

25 mm

32 mm

40 mm

50 mm

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. For Concealed Work CPVC Pipes Class-I,SDR-11

15mm

20mm

25mm

Supplying, fitting & fixing PVC pipes for underground work of approved make of (medium duty) conforming to ASTMD - 1785 & threaded to match with GI Pipes as per IS : 1239 (Part - I). With all necessary accessories, specials viz. socket, bend, tee, union, coss, elbo, nipple, lomgscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials, jointing materials, cutting pipes, making thread, cutting trenches upto 1.5 metre below suffacein all sorts of soil & refilling the same directed complete in all respect. (Payment will be made on the centre line measurments of the total pipe line including all specials. No separate payment will be made for assesories, specials) PVC Pipes (Dia) 40mm

Supply, Fitting & Fixing of complete Bottle waste tap. 32 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer.5000 litre capacity capacity

Labour for hoisting plastic water storage tank. Above 1500 litre upto 5000 litre capacity. Upto 1st story from GL.

Labour for hoisting plastic water storage tank. Above 1500 litre upto 5000 litre capacity. Extra for each additional floor.

Supplying, fitting and fixing white vitreous china best quality approved make wash basin or oval type (Counter top with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. 550 mm X 400 mm size

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 600 mm lomg

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 750 mm long

Supplying,fitting and fixing approved brand 32 mm dia. P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. 750 mm long

Supplying, fitting & fixing UPVC pipes All Type and fittings conforming to IS:13592- 1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid / Bitumen /M-Seal etc) complete. 160mm Dia

Supplying, fitting & fixing UPVC pipes All Type and fittings conforming to IS:13592- 1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid / Bitumen /M-Seal etc) complete. 110mm Dia

Supplying, fitting & fixing UPVC pipes All Type and fittings conforming to IS:13592- 1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid / Bitumen /M-Seal etc) complete. 75mm Dia

Supplying fitting & fixing W.C. Connector (450 mm long) W / lipring 75 mm

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With 'P' trap

Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With 'S' trap

Suppling, fitting and fixing Wall mounted water closet of white glazed vitreous chinaware of approved make and brand in position complete with necessary nut and boalts (Equivalent to Code No. 20061 or 92065 & Model Studio or Rubbic of Hindware or equivalent.)

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap. 580 mm X 440 mm

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. E.W.C. Plastic (hallow type) black

Supplying, fitting and fixing Half round channel with or without outlet as required set in cement concrete (6:3:1) with jhama chips complete. 600 mm X 150 mm. Salt glazed stone ware.White vitreous chinaware

Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. C. P. Flush Pipe

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. 465 mm X 355 mm X 265 mm

Supplying, fitting and fixing porcelain partition wall of approved make of size 618 mm X 310 mm complete in all respect.

Supplying, fitting and fixing liquid soap container. Cromium plated.

Supplying, fitting & fixing Supplying, fitting and fixing porcelain soap tray of approved make. Recessed soap tray of size 150 mm X 150 mm

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm

Supplying, fitting and fixing towel rail with two brackets Aluminium. 25 mm dia. & 750 mm long

Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling,15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover with farme or RCC Grating with frame of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. With Pakur variety

iii) Extra for each additional depth of 150 mm or part thereof beyond initial 600 mm depth.

Supplying, fitting and fixing shower of approved brand and make. Hand Shower (Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar).

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe.

BOQ Main Gate

Dismantiling all types of masonry by excepting cement concrete plain or reinforcement stacking serviceable materilas at site & removing rubbish as directed within a lead of 75m. Any floor & roof

Dismantiling all types of plain cement concrete work, stacking serviceable materials at site & removing rubbish as directed within a lead of 75m. upto 150mm thick. Any floor & Roof

Earth work in excavation of foundation trenches or drains, in all sorts of soils (including mixed soil but excluding laterite or sandstone) i.c. removing, spreaqding or stacking the spoilts within a lead of 75 m 'as directed. The item includes necessary trimming the sides of trenches. Levelling, dressing and ramming the bottom, bailing out water etc. as required complete.. Depth of excavation not exceeding 1500 mm.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm. As directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand.

Supplying & laying Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Ordinary Cement Concrete M-15 (mix 1:2:4) with graded stone chips (20 mm down) excluding shuttering and reinforcement. as per IS 456 - 2000. Pakur variety..

Batch Mixed concrete of M 25 Grade with well Graded stone chips of 20 mm nominal size containing designed quantity of cement per Cu. M of Wet concrete produced in computerised batching plant under controlled condition using approved super plasticizer designing concrete mix following I.S 10262 and I.S. 456 transporting the mix with agitation in transit mixer to work site depositing the mix on a platform erected for the purpose at required level of concreting and then placing the mix in its final location of form work compacting and curing the same complete as per specification and direction of the Engineer-in charge including hire charges of computerised batching plant, transit mixer with all accessories vibrators etc. inclusive of all other incidental charges in this connection complete but excluding cost of hire charge of platform and its supporting staging which would be paid through separate item. Consumption of cement will not be less than 300 Kg of cement per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. foundation, basement all floor, Roof & above .

Hire and labour charges for shuttering with centreing and necessary staging. using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works. Steel shuttering or 9 to 12 mm thick approved quality plyboard shuttering in any concrete work.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. Tor steel. For works in foundation, basement and upto roof of ground floor / upto 4 m

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar ic. rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, ic.throating, nosing and drip course where necessary. With 1:6 cement mortar. 20 mm thck plaster in ground floor.

Supplying, fitting & fixing M.S. gate/ ( gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the) structural works with hollow sections ( square or rectangular shape) conforming to IS: 806-1957 & IS:1161-1958) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1956 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.

Locking arrangement, rails bottom rollers for Jail type doors including supplying fitting and fixing in position complete as per approved design.

Holding down bolt with nut including 100 x 100 x 6 mm plate washer at bottom fitted complete and packing the hole with cement concrete or cement grout as directed. 20 mm dia bolt. 450 mm long

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface : Two coats (white in shade)

Supplying and applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint The rate includes cost of material, labour, scaffolding and all incidental charges and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. Two Coat. any floors. Roof & above.

Supplying, and, applying protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Two Coats. Super Protective 100% Acrylic Emulsion. any floors. Roof & above.

Supplying, and, applying Interior grade Acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. Solvent based interior grade Acrylic Primer. any floors. Roof & above.

Supplying & Applying acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : Two Coats. Luxury Quality. The rate includes cost of material, labour, scaffolding and all incidental charges. any floors. Roof & above.

Chipping of concrete surface before taking up Plastering work (including cost of all tools, labour, scaffolding & other initial charges). Thls work should not be excuted without specific permission of Engineer-in-charge. Complete in all respect all floor roof & above.

Supplying fitting & fixing bubble free float glass of approved make and brand conforming to IS : 2835-1987. 5 mm thick clear glass. coloured, toughened glass conforming to IS: 2553-1992 (part-II)5mm thick coloured / tinted / smoke glass.

Supplying, fitting & fixing granite slabs 15mm to 18 mm. thick with uniform texture & without decorative veins in columns, wall, facia etc. with 15 mm thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of all materials, labours, scaffolding, staging ,curing and roughening of concrete surface complete. [Using cement slurry at back side of granite @ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m] Area of each Granite slab above 1.00 Square meter.

Supplying and application of chemical for post Installed rebar connection by using ETA approved for seismic criteria In rebar connection, Including drilling hole to the required depth by rotary hammer drill, cleonlng with brush & jet of clean air, /filling chemical(HIT-RE 500 or equivalant) using serrated nozzle to eliminate mIxIng error and in a voldless manner IncludIng charges for all tools & plants. Application to be designed for post· Installed rebars as per ECZ / TR023 or relevant tested and accepted design guidelines and the design document to be furnished by the manufacturer. The chemical should have ETA apprOVal for seIsmIc criteria of rebar fixing whIch should be furnished by manufacturer. The installation and the setting instructions should be strIctly followed as per manufacturer's specl/icatlons as approved by EICprior to drlll/ng along with post· Installed rebar embedment design report. The existing concrete member should be scanned using rebar scanner to avoid hitting existing reinforcement in concrete during drilling. complete in all respect & all floor, Roof & above.

Cost of post installed rebaring application with chemical as speclfled for 8 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 10 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 12 mm dia per cm of depth

Cost of post installed rebaring application with chemical as speclfled for 16 mm dia per cm of depth

BOQ Signage

Designing, Supplying, fabrication Fitting & fixing (including scaffolding if required) Webel Logo (Top -18 gz, side-22 gz ) Stainless steel 304 Grade, Colored Powder coating 60-70 micron, individual letter 2 inch raised with Led halo effect (Including all electrical material, SMPS, wiring, etc. ) to be fixed at building side or roof top (including all necessary fittings & Scaffolding) etc. size: Webel-40 inch Height. The work is to be done as per the directive of the Engineer- in- Charge.

Supplying, Fitting & Fixing M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, Welding, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. For structural members of specified sections weighing not less than 22.5 Kg./m. (M.S structure for Webel letter fixed at main building roof Top fixed with Nut bolt, holding down bolt, including all necessary fittings, Scaffolding ).

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. On steel or other metal surface : With super gloss (hi-gloss) - Two coats

Designing, Supplying, fabrication Fitting & fixing "ELECTRONICS MANUFACTURING CLUSTER, AT FALTA, SOUTH 24 PARGANAS" (Size-18 inch) (Top -18 gz, side-22 gz ) Stainless steel 304 Grade, Colored Powder coating 60-70 micron, individual letter 2 inch raised with Led halo effect (Including all electrical material, SMPS, wiring, etc. ) to be fixed at building West front side (including all necessary fittings & Scaffolding) etc. size: 18 inch Height. The work is to be done as per the directive of the Engineer- in- Charge. (Height of the letter may vary as per actual site condition and final layout and pro-rata payment will be considered for the same)

Supplying Fitting & fixing (including scaffolding if required) Floor indentification two colour vinyle signage / name plate on clear 3 mm acrylic sheet with requited writing content. Signage (i.e., Ground Floor, 1st floor 2nd, Third, 4th Floor, Stair, Electrical room, Module, WEBEl office, Plot Marking Canteen,Conference, Janitors room & others if Required …etc.) at each stair enclosure on every floor, indicating the floor number in words, lettering (any style) size shall be 5cm with contrasting colour from back ground. Any height & Any floor. The work is to be done as per the directive of the Engineer- in- Charge.

Supplying fitting, fixing signage display board for Entrepreneur in front of every module, Reception and other if required at specific areas. Complete in all respect as per direction with supply of the following materials -3.0 mm out door ACP Sheet, 4mm clear acrylic sheet including necessary cutting 1"x1" .16 gz sq pipe with painting .power coated aluminium angle ( 1'x1.6") al. silding channel inculding other hardwares fittings required design art, labour traspotation, Any height & Any floor. The work is to be done as per the directive of the Engineer- in- Charge.

Designing, Supplying, fabrication Fitting & fixing (including scaffolding if required) of content "SUPPORT SERVICE BUILDING" Webel Logo (Top -18 gz, side-22 gz ) Stainless steel 304 Grade, Colored Powder coating 60-70 micron, individual letter 2 inch raised with Led halo effect (Including all electrical material, SMPS, wiring, etc. ) to be fixed at building side or roof top (including all necessary fittings & Scaffolding) etc. size: Webel-24 inch Height. The work is to be done as per the directive of the Engineer- in- Charge. (Height of the letter may vary as per actual site condition and final layout and pro-rata payment will be considered for the same)

Supplying, erection, fitting and fixing of colour flex print Hoarding Sign Board of 2.5m x 1.2m size fixed 2.5m above ground level with MS structure and GI sheet, black acrylic primer painted with all accessories (nut, bolt, clamps, foundation, etc.). The schematic drawing to be followed for consideration of minimum dimension. The matter for the flex will be provided by WBEIDCL and the same has to be composed by the agency for printing in the flex. The hoarding to be installed over GI sheet with MS structure. The MS structure should have adequate foundation with concrete. The structure should be safe against self and wind load. The work is to be carried out as per the direction of the Engineer In Charge.

Designing, Supplying, fabrication Fitting & fixing (including scaffolding if required) of content "MANUFACTURING SUPPORT BUILDING" Webel Logo (Top -18 gz, side-22 gz ) Stainless steel 304 Grade, Colored Powder coating 60-70 micron, individual letter 2 inch raised with Led halo effect (Including all electrical material, SMPS, wiring, etc. ) to be fixed at building side or roof top (including all necessary fittings & Scaffolding) etc. size: Webel-24 inch Height. The work is to be done as per the directive of the Engineer- in- Charge. (Height of the letter may vary as per actual site condition and final layout and pro-rata payment will be considered for the same)

SUBMERSIBLE PUMPSET & ACCESSORIES

Supplying, fitting, fixing and lowering inside the tubewell or Under ground reservoir submersible pump having delivery outlet fitted in spring loaded non return valve capable of delivering required discharge and against a total head from all cases ( Duty conditions given below )directly coupled with submersible motor of reqd. HP to give the required discharge suitable for operation 340-400 volts plus minus 8%, 3 phase, 50 c/s AC supply. The materials of pump and motorsshaft aluminium bronze thrust bearing plate. Noryl diffuser, with necessary accessories for submersible pumping set of approved make / model and tubewell top cover suitable for pump set (before procurement, manufacturer's test report / performance curve chart etc. to be submitted for approval) (Crompton or equivalant) 7.5 H.P.

Supplying, fitting and fixing 80 mm dia GI bend having one end threaded and socketed other end flanged with special arrangements for fitting and fixing pressure gauge.

Supply fitting and fixing 100 mm dia pressure gauge (0 to 7 kg / sq cm minimum) with controlling cock and brass "U" syphon.

Supplying, fitting and fixing electrical water level guard with two pole electrodes.

Supplying of GI pipe of TATA make of 80 mm dia (medium quality) including necessary sockets for column pipe. 80 mm dia

CI sluice valve with flanged ends drilled to as per IS 1358/1962 and having all cost component as per IS 780/1971 solid forged bronze inside screw spindle having ultimate tensile strength not less than 4.72 MT / sq.cm. spindle nut valve and seat faces of hardware resisting manufactured from best quality gun metal, conforming to IS 780/1971 paint tested to 21 kg. (Hydraulic Pressure) sq.cm. valve opening to anticlockwise direction fitted and fixed complete. 80 mm dia

Supplying, fitting and fixing CI non return valve with flanged ends drilled to as per IS 1358/1962 including necessary nuts and bolts, rubber insertion etc. complete (IS marked). 80 mm dia

Supplying, fitting and fixing wrought iron flange of approved quality with washer and bolts as per standard joints complete in all respects. 80 mm dia

Supplying, fitting & fixing approved brand 32 mm PVC waste pipe, with coupling at one end fitted with necessary clamps 750 mm long

Earthing with 50 mm. (2") dia. Galvanised iron pipe 3.64 mm. thick x 3 Mtr. (10') long and 1x4 SWG G.I. wire (4 Mts. Long) 13 mm. (1/2") dia x 80 mm. (3") long G.I. bolts double nuts double washers including S/F 15 mm. dia. G.I. pipe protection (1 Mtr. long) to be fitted with bitumen partly under the ground level and partly above the ground level driven to an average depth of 3.65 Mts. (12') below the ground level and restoring the surface duly rammed. (Tata M)