West Bengal Electronics Industry Development Corporation Limited Tender

Supply, fitting & fixing of flush door bolt. At any floor & any location.

Supply, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks, PVC connector, CP over brass spreader, dome shaped CP waste grating of 32 mm complete. Size 635 mm X 395 mm X 420 mm or may be decided by WBEIDCL. Model number, color, design will be decided by WBEIDCL. At any floor & any location.

Supply, fitting and fixing of Urinal Push Cock along with all fittings

Supply, fitting and fixing of Urinal Spreader along with all fittings

Supply, fitting and fixing of waste Delivery pipe

Supply, fitting and fixing E.W.C. at existing line in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts, seat cover etc. With 'S' / 'P' trap as applicable. Model number, color, design will be decided by WBEIDCL. At any floor & any location.

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete. The rate is including of 'P' or 'S' trap & the cost of concrete for fixing. 580 mm X 440 mm or may be decided by WBEIDCL. Model number, color, design will be decided by WBEIDCL. At any floor & any location.

Supply, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. Model number, color, design will be decided by WBEIDCL. At any floor & any location.

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connector pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. Pillar cock jaquar make. Model no PRS-031 of Jaquar or as decided by WBEIDCL. At any floor & any location.

Supplying, fitting and fixing of Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. PRS-077 of Jaquar or as decided by WBEIDCL). At any floor & any location.

Supplying, fitting and fixing of bib cock with wall flange. Chromium plated Bib Cock (Equivalent to Code No. FUS-29037 of Jaquar or as decided by WBEIDCL). At any floor & any location.

Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. At any floor & any location. Size will be decided by WBEIDCL.

Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbow, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials, chase cutting in walls & repairing the same.). 25 mm dia. medium quality. Concealed work. At any floor & any location.

Supplying, fitting and fixing towel rail with two brackets. C.P. over brass. 25 mm dia. and 600 mm long. Design will be decided by EIC. At any floor & any location.

Supplying, fitting and fixing of CP 2-way bib Cock - 15 mm, supplied, fitted and fixed. (Code No 29041 of JAQUAR or as decided by EIC) & Hand Shower (Health Faucet) with 1mtr Fexible Tube with Wall Hook (Equivalent to Code No ALD-573 of Jaquar or as decided by EIC). At any floor & any location.

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units: Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. , glass, neoprene / EPDM gasket, locking arrangement and rollers. Louvered window. The rate is inclusive of removal of existing aluminum / MS windows from the wall, store at some designated place & repair all the damages of the wall & disposal of the glass beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. At any floor & any location.

Supply, fitting & fixing of frostet glass of approved make and brand in aluminum louver / windows conforming to IS: 2835-1987. 4 mm thick. At any floor & any location.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 4mm thick coloured / tinted / smoke glass. At any floor & any location.

Supplying, fitting and fixing liquid soap container. Chromium Plated. Sizes, design & model will be decided by EIC. At any floor & any location.

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor & disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge.

Labour for dismantling G.I. pipe with fittings. 15 / 20 /25 mm & store at some places inside the premises as decided by the EIC.

Supplying, fitting and fixing 18 mm thick marble partition slab with chawk doongri marbel square cut, both sides polished with two front corners rounded and edges polished. Size, texture & color will be decided by EIC. At any floor.

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make with necessary short pieces & other consumables (if required), tested to 21 kg per sq. cm. (for water lines only). 25 mm. The rate is inclusive of carefully removal of the old existing valve from the pipeline & store at some places in the premises as decided by EIC. At any floor & any location.

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make with necessary short pieces & other consumables (if required), tested to 21 kg per sq. cm. (for water lines only). 40 mm. The rate is inclusive of carefully removal of the old existing valve from the pipeline & store at some places in the premises as decided by EIC. At any floor & any location.

Dismantling & removal of urinals and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. At any floor & any location.

Carefully dismantling & removal of EWC without damaging of existing floor & CI line and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. At any floor & any location.

Dismantling & removal of IWC / squart plate including foot rest and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. At any floor & any location.

Dismantling & removal of Pillar Cocks & store at some places inside the premises as directed by Engineer in Charge. At any floor & any location.

Dismantling & Removal of Angular stop cocks & store at some places inside the premises as directed by Engineer in Charge. At any floor & any location.

Dismantling & Removal of Bib cocks & store at some places inside the premises as directed by Engineer in Charge. At any floor & any location.

Rendering the Surface of walls and ceiling with WATER PROOF wall putty, compitable with acrylic paint of approved make & brand. (1.5 mm thick). At any floor & any location.

Applying interior grade Acrylic primer & Acrylic Emulsion paint, including putty if required, of approved quality & brand on plaster or concrete surface old or new surface including scraping & preparing the surface throughly, complete as per manufacturer's specification & as per direction of EIC. (Solvent based interior grade Acrylic Primer & Paint is standard Quality). (One coat of primer + Two coats of paint). (ICI / Asian Paint or any other brand as approved by WBEIDCL).

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. With 1:6 cement mortar. 15-20 mm thick plaster. At any floor & any location.

Dismantling all types of masonry excepting cement concrete plain or reinforced, including removal of rubbish from the working site and disposal of the same beyond the WBEIDCL compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. At any floor & any location.

125 mm. thick brick work with 1st class bricks in cement mortar (1:4). At any floor & any location.

Supplying, fitting & fixing Aluminium domical grating & removal of old one. 125 mm

Supplying, fitting & fixing UPVC pipes, including all specials, bends etc (B- Type) and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. 110 mm. Approved brand Astral, Supreme & Finolex. The rate is inclusive of carefully removing of EWC or IWC or Squart plate & refixing the same, if required. At any floor & any location.

Labour for dismantling GI / PVC/ CI pipe with fittings. 110 mm. At any floor & any location.

Supply & installation of Acrylic Sheet name plate for doors of toilet. The written matter, color, front will be decided by WBEIDCL. Size of the board 15 " X 5".

Supply, fitting & fixing of Chromium plated double coat Hook (Equivalent to Code No. 35761 & Model - KUBIX of Jaquar or similar).

Taking out shutter of wooden door, dismantling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same with old fittings but with new screws as necessary.

Supplying,fitting & fixing granite slab 15mm to 18mm thick in floor, lobby, stair, landing, counter and treads etc. over 20mm (avg) thick base of cement morter (1:2) laid with white cement slurry @ 4.40Kg per Square meter before placing of granite and jointed with white cement slurry @ 2.0 Kg per square meter with necessary pigments and complete as per direction of Engineer-in-charge including cost of all materials, labours, curing and roughening of concrete surface complete. The rate also inclusive of installation of wash basin in the granite counter with necessary cutting in the slab.

Supply, fiting solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor. (a) 35 mm thick shutters (single leaf) Sq.M. 2659ting and fixing of 1" Gate Valve (Leader)

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation for additional depth beyond 1,500 mm. and upto 3,000 mm. but not requiring shoring.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation

Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevant I.S.Code. For 100 users With Pakur variety. (SAIL/TATA/RINL)

Constructing Inspection pit to a depth of 1.5 metre (inside), 250 mm thick 1st class brick work (1:4) in all sides over a layer of jhama brick soling and 150 mm thick cement concrete with stone chips (1:3:6) including necessary earth work, fitting and fixing approved type S.W. master trap, constructing masonry invert with cement concrete (1:1.5:3) with stone chips, plastering inside and outside (outside upto 300 mm below G.L.) with 20 mm thick cement plastering (1:4) and neat cement punning, including supplying,fitting and fixing one 560 mm. dia R.C.C. manhole cover of approved make with R.C.C. slab of 100 mm thick with cement concrete (1:1.5:3) with stone chips including necessary reinforcement (upto 1%) and shuttering and necessary corbelling brick work (1:4) so that the R.C.C. cover slab rests 150 mm above adjucent G.L., cement plaster (1:4) 10 mm thick on all external surfaces of the top slab as directed complete in all respect and removal of surplus earth with all costs of labour and materials (excluding the cost of master trap only). 1050 mm X 750 mm (inside) chamber including fitting and fixing S.W. master trap of 300 mm dia. of approved make A) With Pakur variety. (SAIL/TATA/RINL)

Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia. (SAIL/TATA/RINL)

Supplying, fitting and fixing in position R.C.C. Manhole/ pit cover of approved make with rim of approved make (Heavy type) 560 mm dia.