West Bengal Agro Industries Corporation Limited Tender

Anti-termite treatment to the soil under floor with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight including drilling vertically 12mm.dia holes at the junction of floor and wall at 300mm.interval to reach the soil below using hand operated pressure pump to squirt chemical emulsion into the pump to squirt chemical emulsion into the holes at the rate of one litre per hole. The holes shall be sealed after operation to match with the existing floor. The entire work is to be carried out as per specification laid down in para 4.3.1.4 of code I.S.-6313 (Part-III)-1981.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powered earth or local sand, as per direction of Engineer-in-Charge.

Cement Concrete with graded stone ballast (40 mm size) excluding shuttering etc. as per direction of Engineer-in-In 6:3:1 proportion.charge, complete. In 6:3:1 proportion.

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. Earth obtained from cutting

Controlled Cement concrete with well graded stone chips (20 mm nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis ofpreliminary test and job mix foumula. In ground floor and foundation.[using concrete mixture] M 25 Grade/ Pakur variety

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction. Tor / Mild Steel.Engieer-in-Charge. SAIL/TATA/RINL

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc,Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment for gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.II) For Structural Works in Roof Trusses etc. using joists, channels and angles of specified section weighing less than 22.5 kg/ m

Hire and Labour Charges for shuttering with centering and necessary staging up to 4 m using approved stout props and thick hard wood planks of approved thickness with required bracings for concrete slabs, beams, columns, lintels, curved or straight including fitting, fixing and striking out after completion of works. Using 25 mm to 30 mm thick wooden shuttering as per direction of EIC, complete

Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water ramming complete, including the cost of supply of silver sand (Payment to be made on measurements of finished quantity)

Brick work with 1st class bricks in cement mortar (6:1) in Superstructure

Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary a) 20 mm thick plaster in sand cement morter (1:4)

Plaster ( to wall, floor , ceiling etc. ) with sand cement mortar including Rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface, including threading nosing and drip Course where necessary a) 15 mm thick plaster in sand cement morter (1:6)

Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. ..... {White cement and Pigment to be supplied by the Agency] With Makrana plain pink / Adranga Pink / Garbh Gulabi / Udaypur pink / Udaypur Green / Black Bhaslana Area of each slab/tile exceeding 1.00 sq.m (This item to be executed on specific permission of Superintending Engineer)

Mechanical motor operated rolling shutter.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. 25 mm Thick

Priming one coat on timber, plastered with synthetic enamel / oil bound primer of approved quality including smoothening surfaces by sand papering etc B) On Steel Surface

Painting with best quality Synthetic Enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc on the surface if necessary.b) On steel or other metal surface: with Super Gloss (Hi-gloss), Two coats (with any shade except white).

Providing, fabrcating and fixing of suitable structural glazing works as per drawing made of coloured anodised Aluminium / MS frame works and fixind of glass of approved shade. The glass to be pasted using structural silicon ( DC 995 ) and weathereal silicon to be used ( DC 789 ) the structure complete with all accessories as and where necessary. Complete in all respects as per direction of Architect/E.I.C. at any level.Clear toughened glass 6 mm thick.

Wood work in door & window frame fitted & fixed complete including a protective of painting at the contact surface of the frame /Sal:Local

Supplying , fitting and fixing M.S. Clamp for fixing door and window frame made of flat bend bar ,end bifurcated , fixed in cement concrete with stone chips (1:2:4) fitted and fixed complete as per direction (cost of cement concrete will be paid separately ). i) 40 mm x 6 mm, 250 mm.length.

Panel shutter of door and window as per design (each panel consisting of Single plank with out joint) including fitting and fixing the same in position but excluding the cost of hinges and other fittings. 40 mm thick with plain panel 19 mm thick =Sishu

Anodised aluminium butt hinges of approved quality fitted & fixed with steel screws with ISI mark in position, complete.a) Door (125 mm. x 63 mm. x 3.2 mm size)

Anodised aluminium Socket bolt (Full Curved )of approved quality manufactured from extruded section confirming to I.S. 204/74 fitted and fixed with cadmium plated screw a) Door 225 mm. long x 12 mm.dia bolt

Supplying anodised aluminium catch hook with eye fitted and fixed to shutter and chowkat complete of best quality. /150 mm. long

Anodised aluminium D-type handle of approved quality manufactured from extruded Section conforming to I. S.Specification (I.S.230/72) fitted and fixed complete with continuous plate base ( Hexagonal /rounded) a) 125 mm grip X 10 mm dia rod.

Bronze coated louver type aluminium window.

Supplying & fixing right weight weather resistant pre-finished aluminium composite panel cladding on vertical surface of the Building including supply of all material, labour, tools, tackles, scaffolding etc. complete as per approved manufacturer’s specification (like Alstrong, Aludecor or similar equivalent) and as per detail Architectural drawing. at any level.Aluminium foil thicknes of 0.5 mm on white core .backing and total thickness is 4 mm.Plane sheet

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor)Two Coats Solvent based interior grade Acrylic Primer

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.Two coat

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats

Protective and Decorative Textured exterior high class matt finish paint of approved quality, composed of special Tharmoplastic Resin containing fine crystalline additives derive from Granite as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.Two coat

Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work).with 0.5 mm thick glass

Add Electrification charge 7.5%

Add Plumbing Works Charge 7.5%

Sub Total

GST 12%

CESS 1%