Water Resources Development Directorate Tender

Labour charge for rewinding, water proofing, fitting and fixing fire proof fibre chips on slots for keeping winding wires in posltion, taped by using water proof tape of 660 volts grade with main cable and Each 2341.00 fitted with tight compound by using steel grip tape and vulcanised rubber tape by heating as per direction of E.I.C. 20 H.P Motor

Supplying,fitting and fixing the winding protector on both sides(TopandBottom)

Supplying, fitting and fixing the bush bearing for motor in place of damagedas per approvaland direction of the Engineerin-charge For 20 H.P. & Above

Top

Bottom

Supplying,fitting and fixing stud bolt with nuts for top and bottom cover

Supplying,fitting and fixing stud bolt with nuts and washer for upper flange as per sample

Supplying, fitting and fixing thrust bearingretainer asper sample

Joining water proof cable with the leads of the motor including soldering with requisite water proof insulation and proper joining compound/Vulcanized rubber tape so that proper water proof insulation is assured.

Supplying, fitting and fixing feroasbestos lining on the thrust plate as per direction of the E.I.C.

Supplying fitting and fixing axial thrust plate of motor shaft including supplying of key etc. aII complete as per direction of Engineer-In-charge.12.5 H. P. to 20 H. P.

Supplying, fitting and fixing pivot segment steel balls on the thrust bearing housing as per direction of the E.I.C. ( 6 nos. in one set with rubber guarder/Circlip etc.) 17.5 H.P. to 20 H.P

Supplying, fitting and fixing of (thrust bearing segment) Pivot segments (Set of 6) made from phosphorus bronze as per sample and as per direction of E.I.C. 17.5 H.P. and above

Supplying, fitting and fixing the self aligning thrust plate of the motor shaft Each 280.00 including supplying of key etc. all complete as per direction of E.I.C.

Re·assembling the submersible motor after completion of rewinding and repainting and allied work with the repaired spares parts or new spares where necessary (to be supplied departmentally on requisition) including checking of all accessories and supplying necessary screws nuts and fitting fixing the whole thing properly as per direction the E.I.C.

Painting two coats of both inner & outer portion with best quality synthetic enamel paint (to be approved before use)including smoothing surface by sand paper for removing old paint asper direction of E.I.C Motor

Installation of submersible electro motor pumping set of following capacities by using necessary requisite, tools and plants by lowering the same within the tubewell housing pipe upto the fOllowing depth as per direction by fitting, fixing column pipes and other accessories, fixtures with necessary nuts, bolts and washers and suspending the entire assembly of pump set vertically by fixing the same supported by M.S. clamps over the top of housing pipe, binding the motor cable with each column pipes and drawing cable upto pump controllerlstarter point including opening out of the top cap of housing pipe of the tubewell and testing of motor both in loading as well as in unloaded condition before and after installation of the same. (The rate is inclusive of hiring charges of tools & plants.) (a)100/150/200 cubic metre per hour capacity electro motor pumping set.) Length of pump assembly of any length exceeding 18 metre length.

Withdrawal of electro motor submersible pumping set of following capacities from within the tubewell housing pipe of the fOllowing length by using all necessary requisites tools and plants and carefully as per direction of Engineer-in-Charge and stacking the same properly at site within the tubewell premises complete. (a) 100/150/200 cubic metre per hour capacity electro motor pumping set.) Length of pump assembly of any length exceeding 18 metre length.

Deduction towards dismantled burnt enamelled copper wire from induction motor on the basis of actual measurement to be retained by the agency. Kg 351.00 (Note: In case of PVC insulated copper wire to arrive at net burnt weight 10% deduction will be made) (7.92 kg x 7 nos) = 55.44 kg

Add GST@ 18.00%(after deduction of it no 20 i.e Rs 19459.44 from total amount i.e it no 1 to 19 )

Add cess@ 1.00%(after deduction of it no 20 i.e Rs 19459.44 from total amount i.e it no 1 to 19 & It no 21 also )

(After deduction of Item no 20)