Water Resources Development Directorate Tender

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1.5 m

(A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Labour for laying soiling with departmental bricks including carriage of departmental bricks within a lead of 150 metres preparation of bed as necessary with brick joints properly filled in and packed with brick joints properly filled in and packed with local sand or powdered earth and including necessary cushion of similar materials below the soling (and in between layers when more than one layer is used) (The item included the cost of obtaining local sand or powdered earth) (a) Single brick flat soling (thickness 75 mm)

Ordinary Cement Concrete (mix 1:2:4) with graded stone chips (20 mm. Nominal size) excluding shuttering and reinforcement, if any, in ground floor. as per relevent IS codes. (a) Pakur variety

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work.

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (a) Pakur Variety

Supplying steel reinforcement for R.C.C. works ready to use "cut and bend" rebars (i.e., Stirrups for all types and all shapes, bars of all shapes, tie bars etc. for slabs, beams, columns, piles, raft etc.) of approved make from factory/ work shop to construction site including placing in position and binding all complete as per drawing and direction of Engineer in Charge. Thermo-Mechanically Treated bars of grade Fe- 500D or more. For works in foundation and up to roof of ground floor/ upto 4 m. B. SRMB, ELEGANT STEEL, CAPTAIN, BALAJI SHAKTI, HEXA, RUNGTA STEEL, ADHUNIK, SUPER SHAKTI, SALUJA GOLD, RASHMI TMT, SEL, SEL TIGER.

125 mm. thick brick work with 1st class bricks in cement morter (1:4) in ground floor.

Brick work with 1st class bricks in cement morter (1:6) in ground floor (a) In foundation and plinth

Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) (a) With earth obtained from excavation of foundation.

(a) Supplying, fitting galvanised 3 ply 12 gauge / 4 points line of barbed wire in fencing (holes already made in the body of the post) or fixed by staples tightening and fixing the wires in taut condition with straining bolts including the cost of cutting and of lapping joints in the wire as necessary but excluding the cost of galvanised staples,straining bolt and binding wire where necessary.

Supplying galvanised straining bolts (with eye at one end with double nuts and washers) fitted and fixed complete. (ii) 12 mm. dia. (b) 250 mm.

Supplying galvanised staples fitted and fixed complete. (c) 44 mm. to 50 mm. siz

Supplying fitting and fixing 600 mm (±30 mm) diametre R.B.T (Reinforced Barbed Tape) Concertina fencing on wall top using concertina coils stretched to approx.6 meters length at site clipped with two nos. of horizontal R.B.T strands which will be tensioned and fixed with the vertical M.S angle iron posts by means of security fasteners (such as 'C' clips, R.B.T clips etc.)

M.S. structural works in columns, beams etc. with simplerolled structural members (e.g. joists, angle, channelsections conforming to IS: 226, IS: 808 & SP (6)- 1964connected to one another with bracket, gussets, cleats asper design,direction of Engineer-in- charge completeincluding cutting to requisite shape and length, fabricationwith necessary bolting, metal arc welding conforming toIS: 816- 1956 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 1957, haulage,hoisting and erection all complete. The rate includes thecost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. including handling charges of materials for the work complete. I) For structural members of specified sections weighing less than 22.5 Kg./m

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners, as directed and racking out joints including throating, nosing and drip course, scaffolding/staging where necessary ( ground floor).( excluding cost of chipping over concrete surface). (i) with (1:6) cement mortar. (c) 15 mm. thick plaster.

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. In Ground floor: (iii) Two coats.

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With other than hi-gloss of approved quality (iv) Two coats (with any shade except white)

Painting block letters or digits in Black Japan or any approved paint as per direction. h) Size above 15 cm. and upto 20 cm.

Add GST @ 18% or as applicable as per Govt. rule.

Add Labour well fare Cess @1% of Gross Bill Value