Water Resources Development Directorate Tender

Foundation of Module Mounting Structure: Suitable and stable Reinforced Cement Concrete foundation for dual axis manual tracking Spy Module structure as per approved drawing. c) For 8 module structure.

Power conditioning unit with IP 54 enclosure: Supply, transport, installation and commissioning of IP 54 protected enclosured Inverter Unit qualifying IEC 61683-Efficiency measurement and IEC 60068-2-Environment tandard safety standard suitable for 3 Phase A.C. motor, IGBT based high voltage switching inverter with MPPT technology, to take care of the variation of Sun light and will be suitably mounted inside the metal enclosure. Inverter should have protection against Dry run, Over current, Under current, Over voltage, Under voltage, Short circuit etc. System should be able to run at low sunshine and minimum 7 to 8 hours a day run should be possible during normal sunshine. condition. Inverter should have option to auto start for any short trip off due to low light/ cloudy situation except for dry run. Inverter should 4 be provided with a display to show the various parameter by the user such as Voltage, Current, Solar panel DC voltage, Inverter IGBT temperature, Out put AC voltage, Output frequency, Pump flow (direct or calculated method), Irradiation etc. The stem should store the data at a set interval, be capable to transfer it to external storage device and support communication of its operational parameters and logs over Modbus otocol It should also monitor and save total run time, total water pumped etc. There should be provision for interfacing GPRSbased data transmission. a) For 2 HP capacity Pump-motor set

Cable and Accessories : Supplying, fitting and fixings of UV rated Copper Cable laid inside HDPE conduit and other accessories as per followings with necessary connection with the Solar PV Module, MPPT etc. i. 4.0 Sq mm single core multi studs - 10 Mtrs (Minimum)ii. 6.0 Sq mm single core multi struds -5 Mtrs (Minimum) iii. Lugs, HDPE Pipe, Flexible Pipe, Saddle, Cable tie etc a) For 2 HP per structure

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80mm long GI bolts, double nuts, double washers incl. S & F 15mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: (a) By ISI-Medium GI pipe including excavation of soil for installation of Earth Electrode and filling & ramming and connecting to individual structure to earth electrode including S&F 20 mm x 3 mm Galvanized (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Lightning protection(pole mounted)(: Lightning protection with 3" X 1.5" G.I pipe of 4 mts height with base flange in proper RCC foundation and S & F Lightning Conductor Air Terminal made of 20 mm dia 1000 mm long GI pipe (ISI Medium) having five discharge prongs of 4 SWG GI (Hot Dip) wire at top duly soldered with 7/16 stranded GI (Hot Dip) wire and 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etc including supply & fixing GI (Hot Dip) strips 20 mm x 3 mm thick for horizontal run on the Parapet/Roof/ Wall with GI Saddles 1100 mm apart incl. mending good the damages to building works including Earthing with 65 mm dia GI pipe (TATA-Medium)x 3.0 Mts. long and 1 x 19/10 stranded GI (Hot Dip) wire (4 Mts. long), 20 mm dia x 125 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts

Supply and installation of 3 phase electromotor pump-motor set suitable for Solar operation covering 5 years warranty for the following conditions including loading, unloading, transportation etc.:- a) 2 HP surface mounted Monoblock Pump-motor set suitable for operation in 3 phase 200V series VFD 2.78 Lps discharge at 29 mts. total head suitable for 1.75 Ha/3 Ha CCA Sprinkler operation

Testing and commissioning of scheme after completion of all work

Comprehensive maintenance charges for 4 years beyond 1 year warranty period (which cover monthly inspection, Yearly training to WUA, to attend breakdown within 3 days and to keep the scheme in operation without lapse of time) a) For 2 HP surface pump Total comprehensive maintenance charge is to be withheld in addition to Securirty Deposit. Security Deposit will be released after expiry of warranty period of 1 year & Comprehensive maintenance charges will be released @ i) Rs 3.05 for 2 HP, ii) Rs.2.51 for 3 HP, iii) Rs.2.04 for 5 HP Submersible & Surface per Wp per year at the end of each maintenance period i.e.at the end of 2nd year, 3rd year, 4th year, 5th year. In case the “Bidder” does not provide service during the warranty & comprehensive maintenance period, the amount so held up will be forfeited

For Supply, installation, testing & commissioning of portable Sprinkler Irrigation system

Supplying , Fittings & Fixing of Metal Impact Sprinkler as per IS 12232 i) QRC HDPE Pump Connecting Nipple 63 mm IS: 14151 Part II

Supplying , Fittings & Fixing of Quick Connect Pipe (Metal Latch Type),as per IS-14151 i) HDPE Pipes with Quick Release Coupler(Pipe of Class II; 3.2 kg / cm2 IS:14151 Part I 63 mm diameter & 6m long

Supplying , Fittings & Fixing of Quick Connect Tee (Metal Latch)as per IS 14151 i) QRC HDPE Tee with Coupler (63mm) IS14151 Part II

Supplying , Fittings & Fixing of Quick Connect Tee (Metal Latch)as per IS 14151 i) QRC HDPE Bend with Coupler 90 degree (63 / 50 mm) IS 14151 Part II

Supplying , Fittings & Fixing of Quick Connect Tee (Metal Latch)as per IS 14151 i) QRC HDPE End Plug (63mm) IS: 14151 Part II

Supplying , Fittings & Fixing of Quick Connect Service Saddle (Metal Latch) as per IS 14151 i) QRC HDPE 63 mm Service Saddle IS:14151Part II

Supplying , Fittings & Fixing of Quick Connect End Riser of approved make and quality all complete as per direction of Engineer in charge i) GI Riser Pipe upto 3/4" diameter x 75 cm long

Supplying , Fittings & Fixing of Metal Impact Sprinkler as per IS 12232 i) Sprinkler Nozzles Full Circle (1.7 to 2.8 kg / cm2) 12m to 18m Radius of Throw , 1200 LPH to 1800 LPH Discharge IS12232 Part I

For foundation base for Pumping Unit including construction of Kiosk.

Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes. For foundation. [for Distance 30.0 Km]

Brick work with first class bricks in cement mortar (1:6). (a) In foundation and plinth

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc I) For structural members of specified sections weighing less than 22.5 Kg./m

Supplying 1.5mm thick M.S. sheet fitted and fixed on one or both faces of M.S./ W.I. gate etc. with point welding at not more than 150mm apart complete in all respect as per design including cost of all labour and materials .

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothing surface by sand papering etc. including using of approved putty etc. on the surface if necessary.

Supplying 1 m × 0.6 m × 24 swg MS board containing list of spout wise water users by making numbers of spout as directed by EIC. The board should have base colour - Black and words - White to be fitted and fixed on the wall of the pump house.

Add GST @ 12% except item no 1.01 and 1.04

Add GST @ 5% for Item No 1.01 and 1.04

Add Cess @ 1.00%