Water Resources Development Directorate Tender

Non Return Valve-1.5"CI

BY pass assembly -1.5"x1.5" PVC

FIELD UNIT PVC Pipe 75 mm, Class-II,4Kg/CM 2

PVC Pipe 63 mm, Class-II, 4Kg/CM2

Lateral 16 mm, Class-II,2.5 Kg/CM2

Emitting Pipe 16mm, Class-II,(0.6mX1-4 LPH)

Control Valve 75mm

Control Valve 63mm

Flush Valve 63mm

Throttl Valve-2"

Cost for digging trench for laying Main Line and fitting accessories @5%(item no-1 to 14)

Additional cost for Sand filter ( With Back Wash assemblyIS14606)10M3 /Hrx1.5

Additional cost forfertilisation tanlk with assembly ( With assembly IS14483-Part-II)30 lit.

Solar Module: Supply , transport , installątion and commissioning of ISI marked Solar Modules as per following specification: 1. Cell: Indigenous mono crystalline silicon SPV cells 2. Solar Module: Monocrystalline cell with PERC technology / module with bifacial cell. 3. Standards: 1st marked as per IS 14286 and having certification of IEC 61853(1), 61730(1&2), 61710 4.ModuIes must qualify to lS 170210 (Part 1) 5.Min. Efficiency: 19.5%. 6. Fill factor: More than 75% . 7. Module wattage mismatch in the SPV array: within -t3% 8. Wattage output warranty:ShouId not be less than 90% at the end of 10 years and 80'X at the end of 25 years. 9.The power output of individual PV modules used in the PV array, under STC: minimum 300 Wp. Necessary test certificates also to be supplied. For detail information please see CI. no. 2.1 of technical specification. b) For 2 HP Off-grid Solar Water Pumping System with Monocrystalline/ Monocrystalline PERC/bifacial SPV modules - 2150- 2400 Wp.

Module Mounting Structure ( For 1 HP, 2 HP, 3 HP, 5 HP & 10 HP Solar Water Pumping System): Supply , transportation & installation of G.I Fixed Manual tracking structure made of MS hollow sections, pipes, plates, angles etc as per IS 1161/1239, 1079/2062, to hold min 300 Wp SPV Module as per drawing and specification of MNRE . The steel structure is to be protected with minimum 80 micron galvanisation(hot dip) and provided with fixed arrangement or dual axis manual tracking arrangement for thee times in a day and seasonal tilting are to be regulated to face the sun optimum ( as per requirmenent). The approximate weight of the Module Mounting Structure given ia a clause No. 5.1 should ve followed.

Foundation of Module Mounting Structure: Suitable and stable Reinforced Cement Concrete foundation for dual axis manual tracking SPV Module structure as per drawing. For4 module structure

Power condltlonlng unit with enclosure : Supply , transport , installation and commissioning of Solar Power conditioning Unit consisting of following components and features: 1) Variable frequency Drive with Inbuilt MPPT, voltage range suitable for operating pump-motor set of 1HP to 20 HP, detail mentioned In cl.6.1 2) Power Input : DC source for 1HP, 2HP and 3HP. 3) Power input : AC / DC source or hybrid for SHP and above. 4) Incomer: DC MCB 2 Pole 16 amp upto 5 HP, 25 amp for 7.SHP and 10 HP, 40 amp for 15 to 20 HP as per IS/IEC 60947-2 5) Incomer: AC MCB 4 pole 16 amp for 5.0 HP, 25 amp for 7.5HP and 10 HP, 40 amp for IS to 20 HP ar per IS/IEC 60947-1 6) Type II DC SPD of 40 KA. 7) Type II AC SPD of 40 KA for AC/ DC or Hybrid Input. 8) Dual Input (solar/Grid) 25 amp changeover switch for SHP and 7.5 HP, 40 amp for 10 HP, 63 amp for 1S to 20 HP 9) Reverse protection diode 1600 VDC with heat sink. 10) Data Logger. 11) Remote menltoring system. 12) Should have built -In EMC filters . 13)IP 65 elands for cable In and out. 14) Min. IP 54 enclosure.For detail features, protections, RMS, Communication architecture, Security, Data storage, tolerance of various parameters, standards to be qualified, etc. please refer to CI. 6.1 of technical qualification. Note: AC SPD, AC MCB and Selector switch to be provided only for item no. 3(f) to 3(I). b) For 2 HP capacity Pump-motor set with DC input

Cable and Accessories : Supplying, fitting and fixings of UV rated Copper Cable laid inside HDPE conduit and other accessories as per followings with necessary connection with the Solar PV Module, MPPT etc. i. 4.0 Sq mm single core multi studs - 5 m ( for 2 HP ) & 20 m (for 3/5 HP ) ii. Lugs, HDPE Pipe, Flexible Pipe, Saddle, Cable tie etc.

Earthing: Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: (a) By ISI-Medium GI pipe including excavation of soil for installation of Earth Electrode and filling & ramming and connecting to individual structure to earth electrode including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of 8 swg on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.

a) Lighting System at Scheme: (with lighting Pole) : Dusk to Dawn lighting arrangement of 4 mts height above ground level with(Hot dip) Galvanished 80 mm x 50 mm, Medium duty G.I. pipe with 12 V, 15 Ah 2- in 1 Lithium ion /Fero-phospate battary within built 7-11 watt LED lamp, 50 Wp solar panel to cover the scheme area.The lighting system should be warrented for 5 years rom the date of installation.

Lightning protection (Pole mounted): Lightning protection with 1.5" G.I pipe of 4 mts + 0.75 mtr. height with base flange in proper RCC foundation and S & F Lightning Conductor Air Terminal made of 20 mm dia 1000 mm long GI pipe (ISI Medium) having five discharge prongs of 4 SWG GI (Hot Dip) wire at top duly soldered with 7/16 stranded GI (Hot Dip) wire and 85 mm dia 6 mm thick GI base plate at bottom incl. necessary holes etc . Earthing with 65 mm dia GI pipe (Medium) 3.0 Mts. long and 1 x 19/10 stranded GI (Hot Dip) wire (4 Mts. long), 20 mm dia x 125 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 65 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts. (Provision of one lightning protection for each structure)

Supply and installation of 3 phase electromotor pump-motor set suitable for Solar operation covering 5 years warranty for the following conditions including loading, unloading, transportation etc.:- c) 2 HP ISI marked as per IS 9079 surface mounted monoblock Pump-Motor set with 2.60-2.78 LPS discharge at 26 mts. Total head suitable for 2.0 Ha CCA sprinkler / Drip operation with foot valve, required quantity of flexible suction pipe ( 15 m) , clamps, bend, foot valves and all other accessories to complete connection of suction of suction and delivery side.

Testing and commissioning of scheme after completion of all work

Construction of Pump - Motor Shed of height 0.85 mtr.( as per drawing ) with Hot dip Galvanised ISA 25x25x3 & 1.5 mm MS sheet including foundation Base of 0.95m x 0.65 m for pump unit ( BFS, .075 mm 1:2:4 PCC , 100 mm 1:1.5:3 CC )- for 2 HP and 3 HP surface pump.

Comprehensive maintenance charges for 4 years beyond 1 year warranty period (which cover monthly inspection, Yearly training to WUA, to attend breakdown within 3 days and to keep the scheme in operation without lapse of time) c) For 2 HP both for Submersible & Surface pump. Note : 1 Total comprehensive maintenance charge is to be withheld in addition to Securirty Deposit . Comprehensive maintenance charges will be released @ i) Rs. 0.80 for 2 HP, ii) Rs. 0.80 for 3 HP, Rs. 0.60 for 5 HP & 10 HP Submersible & Surface pump per WP per year at the end of each maintenance period i.e. at the end of 1st year, 2nd year, 3rd year, 4th year & 5th year. in case the "Bidder" does not provide service during the warranty & Comprehensive maintenance period, the amount so held up will be forfeited.

Insurance @ 2% for item no-17, 20, 24, & 26 for a periods of 5 years. Note : 2 1st year's insurance charge is to be paid on production of Original Receipt of premium payment. Remaining 4 years Insurance payment is to be withheld which will be released during 2nd, 3rd, 4th & 5th year on production of Original Receipt of premium payment.

Supplying, fitting and fixing including transportation of sign board for identifying the exact location of scheme (one at road side and other at site) the board will be made 3 mm thick MS plate of size 300 mm x 600 mm and fitted and fixed on 50 mm GI Pipe of IS 1239/90 (part-1) including cutting, welding LS and writting of both sides of Sign board. Base - Yellow, and words - Red. Both bottom end of the stands pipe will be grouted in 1:2:4 CC on a single brick flat soling. This will include one materials and labour complete as per drawing and direction of E.I.C.

Add GST for hole work value @18% or as applicable as per Govt. rule.

Add Labour well fare Cess @1% of Gross Bill Value + GST.