Uttar Banga Krishi Viswavidyalaya Tender

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i ) Pakur Variety

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation, basement and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel JSW/JSPL/SHYAM/ SRMB/BMASL/ELECROSTEEL/SSL

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (f) 25 mm to 30 mm shuttering without staging in foundation

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand..

(II) Cement concrete with 30 mm down graded shingles excluding shuttering. N.B. Variety. In ground floor (a) 1:3:6 proportion

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface].(i) With 1:6 cement mortar,(b) 20 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.

Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and clean and scaffolding complete as per direction of Engineer-in -charge.c) 37.5mm thick

Laying of one no 3.5 core 95 sq mm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 ( eight ) nos bricks per meter , including filling the space between the brick and cable also the trench with shifted soil, leveling up and restoring surface duly rammed from O.H to Generator panel.

Laying of one no 3.5core 35 sq mm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 ( eight ) nos bricks per meter , including filling the space between the brick and cable also the trench with shifted soil, leveling up and restoring surface duly rammed for STI HUB .

Supply and fixing compression type gland complete with brass gland, brass ring and rubber ring and dust and moisture proof entry of XLPE/ PVC armoured cables as below: 3½ core 35 sqmm cable

Supply and fixing compression type gland complete with brass gland, brass ring and rubber ring and dust and moisture proof entry of XLPE/ PVC armoured cables as below: 3½ core 95 sqmm cable

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials :3½ core 35 sqmm cable

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials :3½ core 95 sqmm cable

Earthing with 50 mm dia. ISI medium GI pipe 3.64 mm thick x 3.04 mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 mts. long), 13 mm dia. x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia. GI pipe protection (1 mt. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 mts. below the ground level. for Proposed panel

Connecting the equipments to earth busbar including S & F. 8 SWG copper solid wire on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.Earth wire should be connected earth pit to proposed panel.

Supply of XLPE/ PVC Armoured Aluminium cable (GLOSTER, CRYSTOL, Havells).1.1 kv grade, 3.5 core, 95 sq mm XLPE/PVC armoured aluminium cable,

Supply of XLPE/ PVC Armoured Aluminium cable (GLOSTER, CRYSTOL, Havells).1.1 kv grade, 3.5 core, 35 sq mm XLPE/PVC armoured aluminium cable,

MAIN PANEL - Febricating , supplying , installation, testing and commissioning of wall/ floor mounting Cuibical type L.T. panel board made with 40 x40 x6 mm. ms. angle and 40x6 mm. M.S. flat incl. fabricated with 16 swg. M.S. sheet box for accommodation of the following switches incl. making throughout joining between main switches and BBC and inter connection by suitable size of FR-PVC copper wire, fixing M.S. cable gland and socketing the ends with powder coated approved paint over a coat of R.O. primer as per direction of EIC . The panel board comprising with the following switches:- 415 volt , 200A, 4 bar , copper Bus bar, 415 volt, 160 A, Open execution type main switch S&F HRC fuse (L&T) . 415 volt, 160 A, 4 pole change over - 1 no, 415 volt, 100 A, Open execution type main switch S&F HRC fuse (L&T)-.415 volt, 63 A, Open execution type main switch S&F HRC fuse (L&T)- . . Ammeter & Selector switch (ISI) - Voltmeter & Selector switch (ISI) - , Pilot lamp with sliding fuse (ISI) - Danger board ( 20x30 cm.) - ( Design of panel board will provide by the Department)

Repairing of Generator fuel pump, replacement of AVR, repairing of radiator and other allied works if required.

Add 18.00% GST on total cost from item 1 to 23

Add 1% LW Cess on total cost from item 1 to 24