Uttar Banga Krishi Viswavidyalaya Tender

Supply and placing of sink unit having the dimension of 770 mm (W) x 770mm (D) x 900mm (Ht.). The service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Fittings should be identified with service indexes in the color coding as per DIN 12920. The electrical trunking used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 1.0 mm thick CRCA MS panel. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. The sinks should polypropylene molded construction made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size should be 500 L x 400 W x 300 D mm. Faucet should be 3-way type. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of Wall Bench of overall size of 2030 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 1 storage unit (1D + 2S) . The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of Wall Bench of overall size of 3680 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 2 storage units (1D + 2S) . The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of Wall Bench of overall size of 2480 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 1 storage unit (1D + 2S). The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of Fixed Type reagent shelves workbench, having 4200 mm (L). It should be complete modular design consisting of 2 stage horizontal storage shelves made of CRCA MS with pure epoxy powder coating and having cutouts for electrical switches and sockets. It should have provision for placing Granite pieces (as per requirement in BOQ). The Upright system will form the backbone for internal distribution of GDS, Electrical supply systems Shelves and Top Units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Shelf height should be adjusted with an increment of 1inch / 25mm. Upright should also provide support to Top Units for hanging thus eliminating the danger of fixing the Top Units on non-rigid partition wall / panels. Uprights should be supplied with adjustable feet from -5mm to +20mm. The reagent shelves should also have the provision for housing electrical switches and sockets, data, and voice points. The reagent shelf should be given either for single side use or double side use depending on the approved layout.

Supply and placing of Wall Bench of overall size of 4280 mm (W) x 1540 mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 4 storage units (1D + 2S). The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of sink unit having the dimension of 770 mm (W) x 770mm (D) x 900mm (Ht.). The service fittings should be laboratory grade, and water faucets and valve bodies should be cast red brass alloy or bronze forgings, all fittings should be powder plated unless specified otherwise. Fittings should be identified with service indexes in the color coding as per DIN 12920. The electrical trunking used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from 1.0 mm thick CRCA MS panel. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. The sinks should polypropylene molded construction made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Bowl size should be 500 L x 400 W x 300 D mm. Faucet should be 3-way type. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of L shape Wall Bench of overall size of 1840 mm (W) x 770mm (D) x 900mm (Ht.) on one side 2924 mm (W) x 770mm (D) x 900mm (Ht.) on the other side and 1 corner unit of 900 mm (L) x 900 mm (W) x 900 mm (H) x 770 mm (D). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 3 storage units (1D + 2S) and 1 no of corenr storage unit. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of Wall Bench of overall size of 1280 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness

Supply and placing of Wall Bench of overall size of 2480 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness.

Supply and placing of 1 storage unit (1D + 2S). The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of .L shape Wall Bench of overall size of 1840 mm (W) x 770mm (D) x 900mm (Ht.) on one side 3225 mm (W) x 770mm (D) x 900mm (Ht.) on the other side and 1 corner unit of 900 mm (L) x 900 mm (W) x 900 mm (H) x 770 mm (D). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness

Supply and placing of 3 storage units (1D + 2S) and 1 no of corenr storage unit . The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing Wall Bench of overall size of 2480 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness

Supply and placing of 1 storage unit (1D + 2S). The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.

Supply and placing of Wall Bench of overall size of 1280 mm (W) x 770mm (D) x 900mm (Ht.). All C-Frames assemblies should be manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout. C-frame should be constructed from a rectangular pipe with a cross section of 60mm x 30mm and should be 2 mm thick and should be without a vertical front leg to give a clean look. This shall provide more knee space or leg space and would facilitate uninterrupted lateral movement of the under-bench units within the bench run. The C-frame legs should be supplied with adjustable feet (tolerance from -5mm to +20mm) to correct the unevenness of flooring. The tubular enclosed type of construction shall discourage dust accumulation and unwanted development of bacteria & fungus. Drainage gradient should be well adjusted throughout the length of table and should have horizontal supports for drainage systems. The structure should have a removable back panel to provide access for maintenance throughout the length of table. The C-frame shall also have skirting at back bottom side. It should be suitable for sitting and standing nominal heights of 750mm & 900mm respectively depending on the layout and the requirement of the laboratory. The table depth should be 920 mm. The length of the table should be as per the approved layout (or BOQ). The horizontal members which should connect the c-frames should be made from rectangular pipes of 2mm thickness. Cross-sectional dimensions of the pipe should be 60 x 30 x 2 mm. They should be made of CRCA MS and coated with pure epoxy powder. They should be available in various widths of 600, 750, 900, 1050, 1200, 1350, 1500, 1650, and 1800, depending on the layout of the laboratory furniture. The cover panels should cover the service lines that runs behind for the wall side units and through the middle for the island units. These should be easily removable (unclipped), and the service line be accessed for maintenance. They should be made of CRCA MS with pure epoxy powder coating and are of 1mm thickness. The vertical upright should form the backbone for internal distribution of GDS, electrical supply systems shelves and top units and should be constructed from 16-gauge CRCA formed steel panels with removable covers. Uprights should be supplied with adjustable feet from -5mm to +20mm. The ends and intermediate vertical supports should be 2mm thick aluminum extrusion with MS brackets of 2 mm thick. Metal platform should be put-on over these shelves for taking care of bottle marks/corrosion. Suspended welded cabinet body should be of flush face construction with intersection of vertical and horizontal members like LH and RH side panel along with front horizontal channel, back panel and bottom panel. Removable back panel should be provided to easily access the service lines running behind the cabinet benches. Intermediate horizontal channels should be provided between door and drawer. Shelf should be eight bend panel with 20mm height. The worktop should be 19mm (+/- 2mm) thick Jet-Black Granite worktop. The exposed edges of the worktop should be chamfered and smoothened. The bottom of the worktop should be polished and there should be a V-groove throughout the length of the exposed edges to protect the cabinets from meeting the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness

Supply and placing of 1 storage unit (1D + 2S). The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Shelf height should be adjustable with an increment of 1inch / 25mm. The storage cabinets should have the provision for horizontal sliding to make available leg space as per the need. It should have the provision for relocation anywhere easily. Cabinet should be of square non-sharp edge construction. Doors should be assembled with SS-304 hinge assembly. . Drawer tray should be of single piece construction. Drawer should be well supported on LH and RH ball slide suspension system. Steel door and drawer front should be of double wall construction with sound dampening material filled inside. Doors should be easily removable, and hinges should be easily replaceable. Knee space panel should be in 22-gauge construction. The dimensions of the cabinets should be W = 450/600 (as per the layout) D = 530mm, H = 635/485 mm. The configurations should be 1 Shutter/ 2 Shutters and 1 Drawer as per the layout. The entire material construction for the storage units should be MSCRCA: IS – 513 (1994). Thickness of LH/RH side panels, shutter front, Bottom panel, Top front, Drawer separator, shelf, Alignment channel should be of 1.2mm thk. Removable Back panel, Shutter cover, Fr. Rack strip, Top cover panel should be of 0.8mmthk. The finish of the welded cabinets should be powder coated pure epoxy of thickness 40-50 microns. Handles should be Anodized Aluminium Recessed-Type, of CTC: 160.0mm. Units should have a locking facility with 180° and 10 lever cam lock mechanism. The hinges should be Knuckle-butt type SS Hinge. The screws should be SS304. Shutter should be of twin-type construction with sound dampening effect using profeel. Shutter cover should be equipped with Bump on for sound dampening. Ball Slide for drawer units should be 500mm length.