Uttar Banga Krishi Viswavidyalaya Tender

Fabrication and installation of Executive table with side unit , comprising of a combination of Drawers and Shutters as per approved design or instruction of EIC of Dimension: Length (60 inch), Width (36 inch), Height (30 inch)as per design . with side unit Length (36 inch), Width (16 inch), Height (30 inch) made out of 19 mm thick BWR Plywood Board as main vertical ,Modesty Panel and horizontal supports with 6mm as back panel of side unit.All exposed & visible external surfaces of the unit (except back) shall have 1mm thick laminate of approved brand and shade. All internal surface including shutters and back shall have 0.8mm thick balancing laminate (ivory/white) of approved brand. Shutters shall be complete with soft closing hinges, 200 mm S.S. Handle and locking arrangements. Drawers shall have soft closing telescopic channels, 150mm S.S. Handle, and Locking arrangement.All the exposed edges of the Ply Boards shall have PVC tape of matching colour of Laminates used with a seamless finish. The top of the table will have 8 mm thick clear glass topping.The Table & Side Unit shall be complete with all necessary magnetic catchers, hardwares, screws etc. of approved brand and should be complete in all respect.

Supplying,Fitting fixing Executive Revolving Chair :Seat Back Assembly – The seat and back are made up of 1.2 +_0.1 cm,thick hot pressed plywood measured and upholstered with fabric upholstery cover and moulded polyurethanefoam.The back foam is designed with contoured lumber support for extra support.The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) * 58.0 cm(H) and SEAT SIZE 47.0cm(W)*50.0cm(D). HIGH RESILIENCE(HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45 +_ 2 Kg/m3 and hardness load of 16_+2 Kgf as per IS:7888 for 25% compression. ARMRESTS: The one piece armrest are injection moulded from black Copolymer Polypropylene. CENTER TILT SINCRO MECHANISM : The mechanism is designed with the following feature. 360 degree revoling type. Upright position locking Tilf tension adjustment Seat/back tilting ratio of 1:3.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0_+0.3cm. TELESCOPIC BELLOW ASSEMBLY : The bellow is 3 piece telescopic type and injection moulded in black polypropylene. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33% glass filled Nylon66 and fitted with 5 nos twin wheel castors, The pedestal is 66.3_+0.5cm. Pitch center dia(76.3_+1.0cm with castors) TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in black nylon.

Fabrication and installation of Half Secretariat table , comprising of a combination of Drawers and Shutters as per approved design or instruction of EIC of Dimension: Length (60 inch), Width (36 inch), Height (30 inch)as per design . made out of 19 mm thick BWR Plywood Board as main vertical ,Modesty Panel and horizontal supports.All exposed & visible external surfaces of the unit (except back) shall have 1mm thick laminate of approved brand and shade. All internal surface including shutters and back shall have 0.8mm thick balancing laminate (ivory/white) of approved brand. Shutters shall be complete with soft closing hinges, 200 mm S.S. Handle and locking arrangements. Drawers shall have soft closing telescopic channels, 150mm S.S. Handle, and Locking arrangement.All the exposed edges of the Ply Boards shall have PVC tape of matching colour of Laminates used with a seamless finish. The Table shall be complete with all necessary magnetic catchers, hardwares, screws etc. of approved brand and should be complete in all respect.