The Braithwaite Burn And Jessop Construction Company Limited Tender

Pre-cast RCC Slab of M-35 grade including placeing the same in position. The rate includes cost of all ingradients, form work etc. Including supply of steel reinforcement.

RCC M-30 grade in foundation as per Railway approved drawing and specification. The rate includes cost of all ingradients, form work etc. Except supply of steel reinforcement.

Schedule B

Earth work in excavation for foundations and floors of the bridges, retaining walls etc., including setting out, dressing of sides, ramming of bottom, getting out the excavated material, back filling in layers with approved material and consolidation of the layers by ramming and watering etc. incl. all lift, disposal of surplus soil upto a lead of 300 M, all types of shoring and strutting with all labour and material complete as per drawing and technical specification as directed by Engineer in charge All kinds of soils

Providing and laying in position machine mixed, machine vibrated and machine batched Design Mix Cement Concrete M20 grade (Cast - in Situ) using 20 mm graded crushed stone aggregate and coarse sand of approved quality in Abutment, pier, wing walls and return walls of Mass cement concrete above RCC raft Including finishing complete as per specifications and direction of the Engineer in charge. Payment for cement, reinforcement and shuttering shall be paid extra

Demolishing plain cement concrete including disposal of material within 50m lead 1:2:4 or richer mix with max. 20 mm coarse aggregate

Ordinary Portland Cement grade-43

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies, FOB slabs, walkway slabs and access platform

Providing, Driving and installing Bored cast in situ Reinforced Cement Concrete piles of specified diameter and length below pile cap in M- 35 grade Design Mix Cement Concrete , using 20 mm graded crushed stone aggregate and coarse sand of approved quality, to carry a safe working load not less than specified, excluding the cost of casing pipe but including the cost of shoe and length of pile to be embedded in pile cap etc complete, concreting by machine batching, machine mixing, scaffolding, using Admixture in recommended proportion( as per IS 9103), if approved in design Mix, placing with tremie pipe, chipping off of pile top to remove laitance concrete above cut off level etc, pumping and bailing out water, with all labour material complete including crossing of tracks if required, as per approved drawing, specification and direction of the Engineer in charge. Length of the pile for payment shall be measured Up to the bottom of pile cap excluding the mud mat. Payment for cement, casing pipe & reinforcement shall be paid extra 600mm diameter

Conducting load testing of a single pile Up to following capacity in accordance with IS 2911(Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc with all labour, material, tool & plants, equipment, machinery, etc complete as per drawing and specification, as directed by the Engineer Initial load test above 100 ton capacity Up to 250 ton capacity pile

Routine Load Test above 100 ton capacity Up to 250 ton capacity pile

Lateral load testing of single pile in accordance with 'IS Code of practice IS: 2911 (Part IV) for determining safe allowable lateral load of pile" with all labour, material, tool & plants, equipment, machinery, etc complete as per drawing and specification as directed by the Engineer Piles with lateral load capacity of above 10 ton & Up to 20 ton

Schedule C-Schedule C (with free Supply of reinforcement from BBJ)

Twisted steel / deformed bars Gr. Fe 500 (TMT Bars or HYSD Bars.)upto 12mm dia (unloading, stacking, straightening, bending, carraiage to location, placement, binding with binding wire, etc., as per drawing, specification, etc. complete)

Twisted steel / deformed bars Gr. Fe 500 (TMT Bars or HYSD Bars.) over 12mm dia (unloading, stacking, straightening, bending, carraiage to location, placement, binding with binding wire, etc., as per drawing, specification, etc. complete)