Technical Education And Training Department Tender

Gauge snap Go and Not Go 25 to 50 mm by 5 mm, Set of 6 pieces

Gauge plug Single ended 5 to 55 by 5 mm. Set of 11pcs.

Gauge telescopic set. 8 - 150 mm

Dial test indicator on stand 0.01 mm least count

Sine bar 125 mm

Dial Vernier ca liper. (Universal type) 0 - 300 mm, LC 0.05 mm

Screw thread micrometer with interchangeable. Pitch anvils for checking metric threads 60. 0 - 25 mm LC 0.01 mm

Depth micrometer. 0-25 mm Accuracy 0.01 mm with standard set of extension rods up to 200 mm

Digital vernier caliper. 0 - 150 mm with least count 0.02mm

Digital Micrometer outside. 0 - 25 mm LC. 0.001 mm.

Comparators Gauge - Dial Indication with Stand and Bracket. LC 0.0lmm

Engineer's try squa re (knife-edge) 150 mm Blade

Surface roughness compa rison plates Nl - N12 Grade

Digital Vernier caliper 0 - 200 mm LC. 0.01 mm (Optiona l)

Vernier Bevel protector Range 360deg, LC. : 5min(150mm blade)

A) Compressor unit suitable for Pressure: 8 bar, Delivery: 50 lpm (or more), Reservoir capacity: 24 Litres (or more), 230V, 50 Hz, with pressure regulator and water separator. B)Pneumatic Trainer Kit, each consisting of the following matching components and accessories: - 01 sets I. Single acting cylinder Max. stroke length 50 mm, Bore dia. 20 mm - 1 No II. Double acting cylinder Max. stroke length 100 mm, Bore dia 20 mm, magnetic type - 1 No III. 3/2-way valve manually-actuated, Normally Closed - 2 Nos. IV. 3/2-way valve pneumatically-actuated, spring return - 1 No V. One-way flow control valve - 2 Nos. VI. 5/2-way valve with manually-operated switch - 1 No VII. 5/2-way valve pneumatically-actuated, spring return - 1 No VIII. 5/2-way pneumatic actuated valve double pilot - 1 No IX. 3/2-way roller lever valve direct actuation Normally Closed - 2 Nos. X. Shuttle valve (OR) - 1 No XI. Two-pressure valve (AND) - 1 No XII. Pressure gauge 0-16 bar - 1 Nos. XIII. Manifold with self-closing NRV, 6-way - 1 No XIV. Pushbutton station for electrical signal input with 3 illuminated momentary-contact switches (1 NO + 1 NC) and 1 illuminated maintained- contact switch (1 NO + 1 NC), Contact load 2A - 1 No XV. Relay station with 3 relays each with 4 contact sets (3NO+1NC or Change-over type), 5 A - 1 No XVI. 3/2-way single solenoid valve with LED - 1 No XVII. 5/2-way single solenoid valve with manual override and LED - 1 No XVIII. 5/2-way double solenoid valve with manual override and LED - 1 No XIX. Power supply unit, Input voltage 85 – 265 V AC, Output voltage: 24 V DC, Output current: max. 4.5 A, short-circuit-proof. - 1 No XX. Profile plate, Anodised Aluminium 1100x700 mm, with carriers. C) Pneumatic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) Worktable – Size (Approx.) L 1200mm X W 900mm X H 900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mm x W495mm x H158mm each, and overall size of Drawer unit (Approx.) - L470mm x W495mm x H825m m and (3) Drawer slide height (Approx.) 85mm. D)Carrier for mounting components, such as PB & relay boxes. E) Cut section model for pneumatic components

A) Hydraulic Trainer Kit, each consisting of the following matching components and accessories: I. Hydraulic Power pack with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @ 1400 rpm operating pressure 60 bar, coupled to a single-phase AC motor (230 V AC) having start capacitor and ON/OFF switch and overload protection, (2) pressure relief valve adjustable from 0 – 60 bar, (3) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and P and T ports. II. Pressure relief valve pilot-operated - 1 No III. Drip tray, steel size 1160 mm x 760 mm. - 1 No. IV. Pressure Gauge Glycerin-damped, Indication range of: 0 – 100 bars - 1 No. V. Four-Way distributor with five ports, equipped with a pressure gauge - 1 No. VI. Double acting hydraulic cylinder with a control cam, Piston diameter16 mm, Piston rod diameter10 mm, Stroke length 200 mm. - 1 No. VII. Suitable Weight for vertical loading of hydraulic cylinder - 1 No. VIII. Mounting kit for weight for realizing pulling and pushing load. - 1 No. IX. 3/2-way directional control valve with hand lever actuation. - 1 No. X. 4/2-way directional control valve with hand lever actuation. - 1 No. XI. 4/3-way directional control valve closed-centre position, with - 1 No. hand lever actuation. - XII. Non-return valve. - 1 No. XIII. Pilot-operated check valve Pilotto open. - 1 No. XIV. One-way flow control valve Withintegrated check valve. - 1 No. XV. T-Connector with self-sealing coupling nipples (2 Nos.) and quick coupling socket (1 No.). - 2 Nos. XVI. Profile plate, Anodised Aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories (To be fitted onto the Hydraulic workstation) - 1 set B) Hydraulic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) Worktable – Size (Approx.) L1200mmXW900mmXH900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mmxW495mm xH158mm each, and overall size of Drawer unit (Approx.) L470mmxW495mmxH825m m and (3) Drawer slide height (Approx.) 85mm. C)Cut-section models for hydraulic components

Split A.C-1.5 Ton with R32 reciprocating compressor

Ductable split A.C 1.5 ton - 1.5 Ton with R410 reciprocating compressor

Deep freezer 200 L carrying with HFC-134a & reciprocating compressor

Display Cabinet 2 ton capacity

Frost free refrigerator Three/four door (Inverter type) 300 L