Sundarban Affairs Department Tender

Supplying, fitting & fixing Cast Iron wheel (after taking out existing one if necessary), rim made of 28 mm. to 36 mm. dia to fit any size of gear rod including carriage to site, painting with two coats of bituminous paint over two coats of red lead primer etc. complete as per direction of the Engineer-in-charge. (b) 60 cm. dia. Cast Iron wheel

Supplying / Replacing Gun Metal Bush for screw gearing arrangement required for hanging arrangement of draw shutter and fitting & fixing with the screw gearing arrangement for operating the draw shutter by taking out the old screw gearing arrangement and Gun Metal bush etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.) (a) 50 mm. dia

Supplying / Replacing Gear rod by a new Mild Steel Gear rod, threaded length as required and fitting, fixing in position with screw gearing arrangement for operating the draw shutter including taking out old gear rod by cutting bolts etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.) (a) 50 mm. dia

Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic 'J' type for making water tight in both up and down stream of draw shutter as well as flap shutter including guide paths, additional M. S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-incharge Musical Note , Harmonic Type (i) 59 mm x 6 mm

(b) 127 mm x 6 mm

Supplying / Replacing at site new pedestal or other similar items for sluices made with Mild Steel plates, angles, channels, holding down nuts & bolts etc. including fitting, fixing in position in concrete or masonry complete as per direction of the Engineer - in -charge.

Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD.. (b) Cement mortar

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

First class Brick work in cement sand mortar insteining of well, pier, abutment, wing wall, parapetsb cross drain. H.P. culverts, guard wall etc. including curing, scaffolding, raking out joints etc. complete including cost and carriage of all materials. (a) In 1:4 proportion.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding /staging where necessary (Ground floor). (iii) With 1:3 cement mortar (a) 15 mm thick plaster

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per 100 sq.m.

Labour charges for collecting or taking out displaced cement concrete or brick blocks of all sizes from slope, bed or apron and relaying the same in canal bed or slopes including clearing, dressing, ramming and preparing bed with necessary earthwork complete within a lead of 200 metre and all lifts complete.

Labour charges for collecting scattered bricks from slope, bed or apron and stacking the same above ground within a lead of 100 metre and all lifts as per direction of the Engineer - in - Charge.

Labour charges for relaying and replacing the displaced dry brick pitching by old bricks including dressing and preparing bed with necessary earth work upto 30 cm depth complete including filling gaps with powdered earth or local sand, including collection of bricks within a lead of 50 metre and finishing the same as per direction of the Engineer - in - Charge. c) 20.00 cm thick

Supplying to site and pitching with 1st class kiln burnt or picked Jhama bricks including dressing, ramming and preparing bed to proper slope complete with necessary earth work not exceeding 300 m.m. in depth and filling gaps with powdered earth or local sand etc. complete ( The rate is including cost of sand). i) With 1st class kiln burnt brick c) 20.00 cm thick

Making filter with well graded 40 mm down ballasts and laying uniformly behind weep holes, below pitching on bed, side slopes including supply and carriage of all materials to site including preparing bed with earthwork up to 30 cm depth, where necessary and compacting with wooden malllet after laying to achieve designed section as per direction of the Engineer- in - Charge (measurements will be on finished work / in stack after deducting necessary void). (a) Jhama ballast

Providing and laying pre-cast brick block pitching of required size (53 Cm. x 53 Cm, x 25 Cm. or as directed by the Engineer-in-charge ) with 1st class kiln burnt bricks in cement mortar including flush pointing on all faces except exposed face which to be plastered with 19 m.m. thick cement plaster , curing, dressing, ramming & preparing subgrade in slopes & bed complete with necessary earth work not exceeding 300 mm in depth with all leads & lifts including cost of all materials/ blocks up to site by all means of transport. The gap between adjacent blocks will not be more than 10 m.m. (Sand, cement mortar mix for making blocks, pointing & plastering is1:4)

Supplying,dressing & staking at site bamboo pins above 5 c.m diametre & upto 7.5 cm diametre.(Dia to be measured at mid length.)

Driving bamboo pins in standing or flowing water including scaffolding and driving appliances. (a) Where boats are not necessary.

Supplying,fitting & fixing with iron nails half split bamboo wailling pieces,(av dia of of bamboo not less than 50 mm.)

Supplying of empty cement polythene bags in good condition.

Filling empty Cement bags with dry earth or sand, stitching the bag (cost of thread included) and carrying and placing them in position and all incidental charges complete but excluding cost of filling materials, (Earth or sand) and gunny bags.

Earthwork in excavation in all kinds of soil for making embankments, repairs to the embankment, closing breaches etc. as per profile including supply and transporting the earth by truck or tractor or any other mechanical means on land , including loading, transporting, unloading and stacking with all lifts bothways and head load where necessary and depositing the same on embankments, clannels, filling depressions in requisite profile, levelling as per direction of the Engineer-in-charge within a lead of, (a) Between 500 metre and 1 Km

Earthwork from borrow pits over existing embankment or for repairs to embankment, closing breaches etc. within an initial lead of 30 metre and lift of 1.50 metre including breaking clods and depositing the same in layers not exceeding 25 cm. and rough dressing etc. complete as per profile.

Earthwork in re-excavation / silt clearance of drainage channels in all kinds of soil including sludge and slush but excluding slush mixed with industrial wastes, sewage, municipal garbage, carcasses, etc and depositing the same as per profile in proper place as directed by the Engineer-in-charge without causing hindrance to traffic and posing health hazard and making arrangement to maintain the site in workable condition including removal of polypacks, brickbats, stone ballasts & boulders, remnants of bullah & bamboo pins and all kinds of water hyacinth, solid / semi solid compact mass formed due to water hyacinth and burning them to ashes or removing outside Govt land where necessary and removal of thick & thorny jungles upto 30 cm girth including shoring and shuttering, if required, and including initial removal of sludge and slush etc by pan or bucket if required, and making arrangement for bailing out of any seepage water and removal of sand or soil blown from underneath, all complete. (Measurement : Pre-work and Post-work level section. Pre-work section to be taken after removal of water hyacinth and all other floating materials etc. (b) By mechanical means using hydraulic excavators within an initial lead of 30 M and an initial lift of 3.0 M

Add 18% for GST

Add 1% Cess