Siliguri Jalpaiguri Development Authority Tender

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) Luxury Quality Ground Floor

1st Floor

2nd Floor

Plaster with sand and cement morter including rounded off or chamferring corner as directed and raking out joints including throatig ,nosing and drip course , scaffolding/staging where necessary (ii) With 1:4 cement mortar b) 15 mm thick Ground Floor

Neat cement punning about 1.5 mm, thick in wall , dado ,Ground Floor

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

P.V.C Partition: Supplying,fitting and fixing the partition, frame will be made with rectangular steel tube of size 50mm x 25mm with wall thickness not less than 1.00mm. The vertical members duly welded to the horizontal members shall be placed between 1000mm to 1200mm apart the entire partition frame will be securedly fixed to the wall, ceiling and floor using rawlplug or wooden gutties and screws etc.the frame will be painted with synthetic paint, the section of the partition frame will then fitted with PRINTED LAMINATED P.V.C extruded hollow section of size 100mm x 25mm. panel with approved quality fixed in the place by means of P.V.C extruded beading on both sides or P.V.C extruded angles (20mmx18mm) on one side and P.V.C extruded beading (9mmx9mm) on other side ,angle/beading will be fixed to the steel frame by 19mm (nos.6) self tapping steel screw placed at an interval of 450mm and complete in all respect as per direction of Engineer-in- Charge with all labour and materials In ground floor..

Plain and finished timber planks in partition, shelves etc. fitted and fixed complete as per design (butt joints) in ground floor. (b) Sishu / Champ (ii) 19mm thick planks

(iii) 25mm thick planks

Digging earth in any soil including mixed soil but excluding moorum, laterite sand stone or any other hard stone including spreading or stacking the spoils within a lead of 75 metres as directed bailing out water upto 1 metre depth, shoring etc., when and if required and back filling with fine sand (including cost of sand) on completion of steining works.ii) 1.5 metre diameter of digging for 1.2 metre internal diameter of well ring.f) Beyond 15 metre upto 18 metre below G.L.

R.C.C. well ring made with cement concrete 1:1.5:3 with stone chips and 0.80% reinforcement (including the cost of shuttering and reinforcement) cast at site fitted and fixed in position after proper curing true to plumb in the well including jointing with cement mortar 1:2 complete as per direction.c) 75 mm thick and 1.5 metre internal dia.Cement for joint filling-8 Kg/m

Supply of Submersible Pump set of 3 H.P, 1Phase , 50 Hz, Water Cooled.(Head Range : 60 Mtr-15 Mtr)(Discharge : 3.6 Cu.Mtr-10.8 Cu.Mtr) (Make:KSB/Crompton/Pluga)

Installtion, Testing and Commissioning of Submersible Pump Set alongwith UPVC Column Pips in the existing borewell including making jointing with jointing kit etc. as required.

Supplying and fixing of 2.5 Sq.mm 3 core copper flat cable as per IS 694:1990 with ISI mark) alongwith column pips / surface / in pipe etc. as required. ( L& T /PLAZA / FINOLEX/HPL)

Supply of 40 mm UPVC Column Pipe of Medium Quality.

Laying of 40 mm dia UPVC Pipe in Ground 0.3 Mtr. Below the ground including trenching and refiling the same etc. as required.

Laying of 40 mm dia UPVC Pipe on Wall Surface with G.I. saddle etc. as required.

Supplying and fixing of 6 MM PVC Coated Steel Rope

Supplying and fixing of 40 MM CI Adopter

Supplying and fixing of U Clamp

Supplying and fixing of Rest Clamp made out of 40 mm G.I Flat

Supplying and fixing of 40 MM G.I.Elbow

Supplying and fixing of 40 MM G.I.Nipple

Laying of 20 mm dia Polythene Pipe in Ground 0.3 Mtr. Below the ground including trenching and refiling the same/Surface etc. as required.

Supplying and fixing of Control Panel Suitable for 2 H.P, 3 Phase with Volt meter, Ammeter, Overload Relay, On/OFF Switch, Dol Starter, Single Phase preventer, Auto/Manual mode, indicator lamps etc . (Make : BCH-CPNSLBW / Siemens/L&T)

Supplying Sign Board ( 1500mmx900mm) made of M.S angle frame (50x50x6) , Sheet (0.50 mm) fitting fixing such with digging holes of dia 450 mm and depth 750 mm in allsorts of soil and repacking and consolidation the gap around the post with cement concrete (1:3:6) including priming, two coat painting & lettering both side etccomplete in all respect as per direction of the Engineer-in-charge.payment of concrete to be made separately.

Add GST @18%

Add Labor Welfare Cess @ 1%