Public Works Department Tender

Supply of BIS approved new generation energy saving, environment friendly and long lasting heat resitant, IP-66 & IK 10 rated 400 watt (maximum) LED flood light luminaries with pressure diecast aluminum housing and PC Cover provided with high power LEDs and secondary optics PC/PMMA lens and Silicon filled BIS registered Potted Vibration proof Driver with built in 4 KV surge protection and 10KV external SPD capable of producing luminaries system Lumen Output≥53000 lumen with Efficacy≥135 lumen/watt, CRI 70, CCT 5700K. (Detailed Specification in Annexure 1A for luminaire and Annexure 2A for driver/control gear) Make:- Wipro/Philips(Signify) / Crompton/ Bajaj (For Highmast at Dunlop More)

Supply of BIS approved new generation energy saving, environment friendly and long lasting heat resitant, IP-66 & IK 08 rated 100 watt (maximum) LED flood light luminaries with pressure diecast aluminum housing and PC Cover with high power LEDs and secondary optics PC/PMMA lens and Silicon filled BIS registered Potted Vibration proof Driver with built in 4 KV surge protection and 10KV external SPD capable of producing luminaries system Lumen Output≥12000 lumen with Efficacy≥120 lumen/watt, CRI 70, CCT 5700K. (Detailed Specification in Annexure 1A for luminaire and Annexure 2A for driver/control gear) Make:- Wipro/Philips(Signify) / Crompton/ Bajaj

Fixing only Street Light Fitting with necessary fixing arrangements including Gl reducer as required for mounting on existing arm brackets

Fixing only Floodlight Fitting with suitable tie clamps and MS plate for mounting on Pole/Tower or similar structure as to GS

Supply & delivery of 4 core 16sqmm of 1.1 KV grade alluminium XLPE, PVC/ armoured LT cable ( Make :Havells/ Polycab/ Glostar /KEI )

Supply & delivery of 4 core 16sqmm of 1.1 KV grade alluminium XLPE, PVC/ unarmoured LT cable ( Make :Havells/ Polycab/ Glostar/KEI ) ( for dunlop underpass)

Laying only Cable upto 50 sqmm through existing RCC/Hume/ GI Pipe/open masonary trench for single, 2, 3, 3½ & 4 core

Laying by catanary system with straining arrangement by 1 no. 7/14 stranded GI wire with 10 SWG soft AL. binding 7/14 stranded GI wire with inequal interval pole by clamp, tanis screw,bobin insulator ,4" X 1/2 nut bolt washer ring insulator (for dunlop under pass)

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below (a) 4 core 16sqmm

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials (a) 4 core 16sqmm

Supplying and Drawing 1.1 KV, 2.5 Sqmm, 3 Core Copper PVC Insulated Sheathed Flexible Cable (Havells / Polycab / Gloster / RR Kabel/KEI) and making necy.connection as required

Finishing of the 2.5 Sqm PVC insulated cu-wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes

Dismantling 4 core 16sqmm of 1.1 KV grade alluminium XLPE, PVC/ armoured/unarmoured LT cable

Dismantling of old existing fittings as directed by EIC

Less Cost of Dismantled Light Fittings Less cost for existing 400W sodium vapour light fittings

Less cost for existing 250W sodium vapour light fittings

Less cost for existing 240W LED light fittings

Less cost for existing 215W LED light fittings

Less cost for existing 70W LED light fittings

Less cost for existing 4 core 16sqmm of 1.1 KV grade alluminium XLPE, PVC/ armoured/unarmoured LT cable. Note: (a) Defect Liability period for the total work including LED fittings will be 5 years. (b)The warranty for the LED street light fittings of BOQ Item Sl. No. 1.00 to 5.00 has to be provided for 5 years by the manufacturer/OEM, the certificate/certificates(in case of more than one manufacturers/OEMs) in respect of which has to be uploaded with tender documents by the bidder. Submission of multiple authentications from different OEM/ manufacturers is allowed. But, if desired by the EIC, under consent of the competent authority, separate authentication from the OEMs other than those submitted with the bid documents may be allowed in the interest of the work in case of L1 bidder. But in such cases, the authentication has to be received by this department directly from the OEMs by name of the respective bidder, over email and also in hard copies within 07 (seven) working days from the date of Provisional Work Order.The Sl. Nos of the Fittings must be mentioned in the Delivery challan on site along with the warranty certificate provided by the Manufacturer/OEM specifying the fittings with Serial number and date. (c) The bidder should upload Technical Data Sheet (TDS) of fittings and Driver, LM79 & LM80 Test Report for the offered LED street Light fittings of BOQ Item Sl. No. 1.00 to 5.00 from the manufacturer's NABL accredited Laboratory/ any other NABL accredited Laboratory failing which the Bid may be rejected.

(d) The illumination design to fulfill the prescribed condition has to be certified by the Manufacturer/ OEM within 07 (seven) working days from the date of layout.The minimum lux should be maintained as 40 lux with Uniformity factor ≥0.6 . (e) One light fitting of each wattage against Item Sl. No. 1.00 & 3.00 as per direction of EIC, randomly selected from the supplied lot consisting of total material, will be tested as follows from NABL accredited Government Laboratory at the cost to be borne completely by the bidder." (i) Visual Examination (for physical dimensions confirmation as per GA Drawing, model no., wattage etc. (ii) Insulation resistance and electric strength. i(iI) Resistance to dust and moisture (iv) Photometric test, (v) Endurance test, (vi) Humidity test, (vii) Drop test, (viii) Vibration test. (ix) Electrical parameters test (namely input power, input current, PF, THD, output power, output current and output voltage, (x) Surge test, k)High voltage and Low voltage test, l)Scratch test. (f) The Agency must procure the materials from the Manufacturer / OEM or from their authorized Sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them. (g) Documents that authenticates such procurement from the Manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the Manufacturer / OEM / authorized sales channel to the e-mail of Engineer-in-Charge and hard copy of it to be submitted during execution of work / submission of bill. (h) If any refurbished material is supplied and installed, penal action will be taken as per existing rules.