Public Works Department Tender

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof of ground floor/upto 4 m (i) Tor steel/Mild Steel I. SAIL/ TATA/RINL

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (f) 25 mm to 30 mm shuttering without staging in foundation

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes

Supplying, fitting, fixing bolts with nuts, washer: (c) Length above 150mm.

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. I) For structural members of specified sections weighing less than 22.5 Kg./m

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. ii) For Structural works like galleries etc

Hire and labour charges for 75 mm dia bamboo railing on 125mm dia Jhau/Eucalyptus or other approved timber 1.4 m above G.L. and 0.60 m below G. including tying strongly with coir ropes and boring holes for posts in any soil /black top/concrete surface, packing the sides etc including cost of carriage of all materials and labour complete and maintaining barricading for a period beyond 5(five) days after the reported & recorded time of completion of the entire work to the satisfaction of Engineer-in-charge,including restoration to the damages of the ground to its original condition as per direction of Engineer in charge after removing the barricade. [Cost of restoration would be paid separately.] 75mm. dia bamboo railing & 125mm. dia Jhau/Eucalyptus/other approved timber posts @ 1.60m apart i) Railing with 4 rows

i) Railing with 3 rows

Hire and labour charges for providing "Drop Gate" with 15 cm dia salbullah of length not less than 8 meter including hoisting and fitting fixing with bolts and nuts to vertical posts (100 mm dia : 2 nos on each flank embedded 750 mm below G.L) and providing counter load of concrete or stone or iron block at the fulcrum end including painting two coats in alternate band providing 'STOP' plate, jute rope of necessary length etc complete including dismantling andremoval as per direction of the Engineer in charge.

Hire and labour charges for 100 mm dia bamboo railing on 150 mm dia Jhau/Eucalyptus or other approved timber posts each 2.0 m in length, tied 2 number post strongly with coir ropes in the fashion of a scissor with a spacing of 1.8 m over pacca road without damaging the surface and tying strongly 3 (three) rows of bamboo railing on each leg and 1 (one) railing connecting all the top junctions including cost of loading unloading, stacking & carriage of all materials and labour complete, clearing the site as per direction of Engineer in charge after removing the barricade.Jhau/Eucalyptus/other approved timber posts with 1.8 m spacing. (i) Railing 4 row on each leg and 1 at pivot point.

Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap.(Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (ii) In Wall a) With 0.6 mm thick sheet

a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With super gloss (hi-gloss) - (ii) Two coats (white in shade)

Loading, unloading and stacking by Manual Means. A. Loading in to trucks at the lifting point, unloading at destination, stacking properly in go downs or yard etc. as directed including carriage by head load up to a lead of 50.00 m at each of the two points. (h) Steel

Cleaning the existing base, base plate by cleaning earth sand etc, straightening the existing holding down bolt by suitable manner with mending good all damages of existing base

Carriage of Steel materials by Machine van for the work of steel barricading at lot-8 kakdwip

Taking out carefully existing railing (tubiar member) by separating posts from base/base plate, fastening the horizontal member from post, cleaning the base plate & other parts, twisting the including down bolt horizontally for smooth vehicular traffic (two times)

Labour for fixing the post with existing base replacing nut where necessary & fixing the horizontal tubular member with post by welding & mending goods all damages

GST ( From Sl-01 to16)

CESS (From Sl-01 to 20)