Public Works Department Tender

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (a) One Coat GROUND FLOOR

3rd FLOOR

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) c) Premium 100% Acrylic Emulsion.

3rd FLOOR

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. Including using of approved putty etc. on the surface, if necessary : a) On timber or plastered surface : With super gloss (hi-gloss) -(iv) Two coats (with any shade except white)

(b) On steel or other metal surface : With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 5mm thick coloured / tinted / smoke glass.

Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts) , reassembling and refitting and rehanging same with old fittings but with new screws as necessary. (Where different parts of same shutter are renewed under different item, payment under item 73 will be made once only).

Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor. 35mm

ii) Godrej Hydraulic door closer fitted and fixed complete. (b) Medium type

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: (viii) 100mm. X 75mm. X 3.50mm.

Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. c) 300mm long.

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base: ( Hexagonal/Round Rod) (V) 125 mm grip x 12 mm dia rod.

(i) Door stopper.(Brass)

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium platedscrews: (vi) 200mm long x 10mm dia. bolt.

Providing and fixing false ceiling at all hights including providing and fixing of feam work made of special section , power pressed from M.S sheet and galvanized with Znic coting of 125 gms / Sqm ( both side inclusive ) as per I.S 277 and consiting of angle cleats of size 25 mm wide X 1.6mm thick with flangs of 27 mm and 37mm at 1200 c/c , one flang fixed to the ceiling with dash fastner 12.5mm dia X50mm long 6mm dis bolts , other flange of cleat fixed to the angle hagrs of 25 X 10X 0.5 mm of required length with nuts and bolts of required size and other end angle hanger fixed with intermediate G.I Chanles of 45X 15 X0.9 mm runing at the spacing of 1200mm C/C to which the celing section 0.5mm thick bottom wedge of 80 mm with tapred flanges 26mm each having lips of 10.5mm , at 450mm C/C , shall be fixed direction prpendecular to G.I Intermedite Channel with Connecting Clips made out 2.64mm dia into 230 mm long G.I wire at every junction , including fixing perimeter Channel 0.5mm thick 27mm High having flanges of 20 and 30mm long , the perimeter of celing fixed to wall / partion with the help of rawl plugs at 450mm centre , with 25mm long dri wall screw at @230 mm intervel , including fixing of gypsum board and perimeter channel with the help of as per drawings , specification and direction of the E.I.C but excluding cost of painting with : ( ISI Mark on Board)

Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material. [Border concrete if necessary to be paid separately]. Note: Sub-grade CBR should not be less than 5.60 mm thick interlocking designer concrete paver block M- 35 grade for light-traffic zone,commercial & office complex,tourist resort as per IS: 15658-2006 (over 20-40 mm medium sand bed on 250mm thk WBM/ WMM base course & 250 mm thk bound gnaular /granular sub-base course including cost of sand for sand bed but excluding cost of base ,sub-base course & subgrade preparation.) (ii) Coloured Decorative

Providing and fixing at or near ground level precast cement concrete in kerbs (size: 410 mm x 310 mm x width 150 mm at bottom with circular nosing at top) (Nano kerb) of cement concreat M25 Grade without reinforcement, fixing as per approved pattern and setting in position at site after preparing the bed grade and slopes by laying Cement concrete with jhama khoa (1:4:8) as per specification and direction of Engineer-in- Charge including filling of joints with 10 mm thick cement morter (3:1) and back filling the vertical piece properly with earth duly compacted and curing the morter joints for atleast 3 days including cost andcarriage of all materials complete. 3.90 metre height

French polishing to wood work including preparing surface (ordinary gloss)

PVC Door Shutter-37 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shadein position, thestyle &rail of the P.V.C .door shutter will be made of rigid P.V.C. multicavity hollow chamber ofsuitable size and section with 2.0mm(+/-0.2mm)wall thickness, the section will have2nos. built inbeads, horizontal &vertical section shall be fixed to each other by self tapping screws and 2nos. of solid plastic or M.S. tubular galvanised brackets of length 200mmx80mm and other 100mm x100mm both 1.20mm in each corner of the shutter frame for placing hinges .Polymer based multicavity hollow section of 105 mm x 37mm with 2.0mm(+/-0.2mm)wall thickness will be fitted in the middle as lock rail reinforced by solid polymer bar of200 mm long at both end sabd screws from both sides. The section frame will then be fitted in by PVC panels of size 100 mm x 20mm with wall thickness of1.2mm(+/-0.2mm) and 2nos .of 6mm dia and screws from both sides 6mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges /haspbolt / towe rbolt /door ringarerequired to be strong enough to with stand wear and tear.Therate is inclusive of cost of all materials, labour,and hire of tools and plants and appliencies.Carriage of all materials taxes and all other incidental charges complete.The rate is exclusive of cost of hinges, hasp bolt, tower bolt,door ring etc. In ground floor.

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials .a) For Exposed Work CPVC Pipes Class-1, SDR-11 15 mm

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. i) Polythene Flush Pipe

Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent)

Supplying, fitting and fixing towel rail with two brackets (b) Aluminium (ii) 25 mm dia. and 600 mm long

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm

Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (b) Anglo Indian (ii) Plastic (hallow type) white

Supplying, fitting and fixing E.W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. (a) With 'P' trap

Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (iii) 600 mm long

Supplying, fitting and fixing Waste fittings complete. (a) C.P. Over brass (ii) 32 mm

Supplying, fitting and fixing pillar cock of approved make. a) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

(f) Hand Shower (Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar).

Supplying, fitting and fixing bib cock or stop cock. (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand).

(b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar