Public Works Department Tender

Repairing pot-holes and making up small depressions using Cationic Bitumen Emulsion conforming to IS 8887- 1978 with stone metals / chips premixed with emulsion in concrete mixer or any other method approved by the Engineer-in-Charge, including cutting the pot-hole area in regular shapes with vertical edges, thorough cleaning & moistening of surface, applying tack coat, filling up the potholes with pre-mixed metals/chips in layer/layers as per specification and direction of the Engineer-incharge, compacting by power roller, finishing the top of repaired surface levelled with adjoining area including cost and carriage of stone aggregates, blinding material & bitumen emulsion, hire & running charges of rollers and other tools & plants, cost of fuel & lubricants and other incidental charges excluding cost of applying tack coat. [Using stone chips of size 22.4 mm and 11.2 mm in 60:40 proportion, premixing with bitumen emulsion @70.7 kg per m3 of loose net volume of stone chips.]

Open Graded Premix Surfacing with Cationic Bitumen Emulsion using 13.2 mm (@ 0.018 m3/m2) and 11.2 mm (@ 0.009 m3/m2) size stone aggregates, premixed with Cationic Bituminous Emulsion (M.S. grade) conforming to IS : 8887-1970 @21.5 kg per 10 m² of surface, including cleaning, moistening the surface, applying tack coat with cationic bitumen emulsion, screening, cleaning and washing the stone chips, intimately mixing with emulsion using Concrete Mixer, laying the mixture uniformly over the surface and rolling with power roller after hand packing and pinning adequately to ensure a compact surface all complete as per specification and direction of the Engineer-in-charge including cost and carriage of stone materials and emulsion, including cost of labour, hire and running charges of road roller and other tools and plants and cost of all other incidental charges including hire charges and cost of fuel and lubricants of machineries and equipment for construction and quality control as per Technical Specification Clause 508.2 for Rural Roads of MORD.

Providing and laying Premixed Seal Coat (Type B) with approved quality sand/grit @ 0.6 m3/ 100 m2 and bitumen binder on thoroughly cleaned black top surface coated with tack coat, including heating and mixing cleaned sand/grit (100 % passing through 2.36 mm sieve and retained on 180 micron sieve) uniformly with bitumen binder, laying and spreading the mix at an uniform rate using suitable means, brushing the surface, if necessary, to ensure uniformity, followed by rolling with power roller including the cost and carriage of binder and aggregates, cost of heating the binder and aggregates and all other incidental charges, cost of fuel and lubricants, including hire charges of machineries, tools & plants required for construction and quality control complete as per Clause 511 of Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge

Providing and fixing at or near ground level precast cement concrete in kerbs (size: 410 mm x 310 mm x width 150 mm at bottom with circular nosing at top) (Nano kerb) of cement concreat M25 Grade without reinforcement, fixing as per approved pattern and setting in position at site after preparing the bed grade and slopes by laying Cement concrete with jhama khoa (1:4:8) as per specification and direction of Engineer-in-Charge including filling of joints with 10 mm thick cement morter (3:1) and back filling the vertical piece properly with earth duly compacted and curing the morter joints for atleast 3 days including cost and carriage of all materials complete.

Plain / Reinforced Cement Concrete in Open foundation with or without reinforcements, in any part of foundation of bridges / culverts with graded stone chips of appropriate nominal sizes, including screening and cleaning of coarse aggregates, fine aggregate (sand) conforming to proper grading zone, both of approved quality and cement, as necessary, cost of curing with water, including cost and carriage of all materials and including preparation of design mix, approval of the same by the Engineer-in-Charge, cost for quality control, sampling, testing etc. including cost of formwork but excluding reinforcement complete as per drawing and technical specifications.

Supplying, fitting, fixing of New PGR by M.S. Structural works with hollow section (Square of rectangular shape) confirming to IS : 806-1968 & IS : 11611-1998) as per design, drawing & direction of Engineer-in-Charge complete including required earth work in excavation, fixing with ordinary cement concrete (1:2:4) with pakur variety graded stone chips finished complete as per direction of Engineer-in-Charge.

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface : With other than supper gloss (hi gloss) - (i) Two coats (any shade except white)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor : One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) Premium 100% Acrylic Emulsion

GST @ 18% over Sl. No. 1 to 14

Labour Welfare Cess @ 1% over Sl. No. 1 to 15.10