Public Health Engineering Department Tender

Engagement of methor with proper placement to work at the Mobile Toilet unit as per order of PHE Dte. (From 06.01.2025 to 17.01.2025) ( 4 Nos. x 3 shift x 12 days.) (Mathor Mazdoor)

Supply and delivery at site the following materials / chemical as per direction & satisfaction of the EIC.

i) Supply of Phenyle in best quality.

ii) Hire charges of Poly Mug (1 litre capacity) in good quality (I.S.I. Mark)

iii) Hire charges of Poly Bucket (15 litre capacity) in good quality (I.S.I. Mark)

iv) Supply of lime in best quality.

v) Supply of bleaching powder in best quality.

Engagement of labour for Dressing & chilcheling, leveling, dismantling and removing all objectionable materials inside the room etc. complete in all respect as per direction and satifaction of the EIC. (Mathor Mazdoor)

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge)

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) a) Normal Acrylic Emulsion

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (iv) 100mm long x 10mm dia. bolt.

Iron butt hinge (80 mm long) (ii) 50mm. X 40mm. X 2.5mm.

Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap (excluding cost of concrete for fixing). 580 mm. x 440 mm.

Supply of G. I. pipes of TATA make including necessary sockets (On hire basis 1/3 of Sch. Rate) (e) 40 mm dia. (i) Light quality

Engagement of Mathor Mistry. (3 nos. x 12 days)

Engagement of Mathor Mazdoor. (5 nos. x 3shift x 20 days)

Labour engaged for installation properly of G.C.I. Sheet over roof of 66 nos. latrine and 24 nos. Urinal at K1 Bus Stand. (Carpenter Helper)

Materials (PVC door frame and shutter and GCI Sheet) carriage by Van from office godown, at PHE campus, Sagar to K1 Bus Stand including loading, unloading.

Supply of Brush in best quality on hire basis

Supply of Broom in best quality on hire basis

iii) Supply of Bucket on hire basis (15 ltr. Capacity)

iv) Supply of Mug on hire basis (1 ltr. Capacity)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With other than hi-gloss of approved quality- iv) Two coats (with any shade except white)

Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. In ground floor.

Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge.

Add 30% Riverine on item no. 07, 09 to 13, 22,23,24 i.e. on Rs. 245209.50

Add GST @ 18% on all item on Rs. 616716.20

Add Labour Welfare Cess @ 1% on Rs. 727725.12