Public Health Engineering Department Tender

Supplying, spreading and consolidating Stone Dust to a depth of 100 mm and above at desired density and C.B.R. as per Specification with power roller to proper gradient and camber including watering as necessary, and lighting, guarding, barricading and making adequate earthen bundh where necessary to protect the edges and curing with water for 2 to 3 days, mending cracks and depressions by rolling where necessary including all incidental charges of roller, cost of fuel & lubricants complete as per specification. ( Ref ; PWD SOR 17 ,Page No 242 ,Item No 4.06)

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm. as directed and consolidating same by thorough saturation with water ramming complete, including the cost of supply of sand.

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

Brick work with 1st class brick in Cement Morter. (1:6) In foundation and plinth.

Plaster (to wall, floor, ceiling etc)with sand & cement mortar includg rounding off or chamfering corners as directed a ramming out joints or roughening of concrete surface by chamfering etc. including threading noising and drip course where necessary.(Ground Floor)(i)15mm thick

Neat cement punning about 1.5mm thick in wall, dado, window, ceiling, floor, drain etc.

Hire and labour charges for shuttering with centering and necessary staging upto 4 mtr using approved about props and thick hard wood planks of approved thickness with required bracing for concrete slabs , beams,columns,lintels,curved or straight including fitting, fixing & striking out after completion of works(upto roof of ground floor) a) 25 mm to 30 mm thick shuttering without staging

Cost for boring any type of soil by augor boring (horizontal) with water jet system including hire charges of machine, tools & plants, all complete with all labour and supply of water etc. as per specification and direction of EIC. i) 80mm to 100mm dia.

ii) 125 mm to 200 mm dia

Cost of pipe line crossing upto (400mm dia.) by adopting trench less technologis (e.g. Jack Pushing Method etc.) for Railway National Highway or any other important road of Heavy Vehicular Traffic of minimum 7.5 m carriage way where no other mode of crossing is possible including the cost of outer most 600 mm dia Hume Pipe (NP3/NP4) as casing pipe, all labours, materials tools and tackles, clearing of sited etc. complete in all respecst but excluding the cost of pipe carrying water.

Supplying HDPE (Materials grade PE-100) pipes conforming to IS 4984-1995 with latest revision & amendments if any with necessary HDPE specials (excluding cost of CIDF valves) including labour charges for earth work in excavation in any kind of soil including mixed soil with boulder,road sub-grade and aits flank but excluding moorum laterite or sand stone / hard rock cutting with chisel required including cutting road flank/ brick pavement etc. without damaging the exisiting telephone/electrical cable line etc.(in case of damage of any type of cable line by the agency at the time of execution necessary damage charge as applicable by the respective authority will have to be brone by the agency at his own cost)upto the depth (av.) so as to maintain 1.10m.earth cushion from top of the pipe upto G.L. including loading unloading carrying lowering laying fitting fixing carefully pipes, valves and specials with the all types of jointing materials in trenches maintaining proper levels and alignment jointing the pipes and specials by butt welding/ adopting suitable method (But weld jointing with help of hydraulic tack and trimming machines, Hitter etc. for reaching at necessary melting point of HDPE pipe so that joint can be monolithic) so as to facilitate the maintenance of pipe line locally as per conventional method in future. Ref : (i) to (viii) to be followed vide L-15 to L-17 of Item No. 3.1 of Corrigendum & Addendum No. -2/2023 dt. 07/06/2023 of PHED SOR. (A) Pressure Rating : PN 6 (ii) Laying of pipe line including cost of pipe, fittings/specials & valves d) 90mm (OD)

e) 110 mm (OD)

Filling the pipe line with water, testing hydraulically as per I.S 3114-1965 (Article-6) in section of a length not exceeding 500mtr. for head of pressure as per specification including supplying installing and fixing all equipments such as diesel pump set, blank flange, pressure gauge, valve, pressure pump and all other tools and plants including drilling topping and plugging of necessary holes to pipes, blocking ends providing temporary thrust block and subsequent blocking of holes and other jointing materials and dismantling and removal of the same including disposal of water etc. all complete as per specification and direction of EIC. The rate is inclusive of cost of requisite water to be arranged by the contractor (Recovery rate of water @ Rs.10.00/m3, if contractor used water from deptt. source). Ref : PHED Sche. B) For uPVC/HDPE Pipe d) 90mm (OD)

e) 110 mm (OD)

Cleaning thoroughly the inner surface of pipe line including specials and valves by flushing with water and subsequently disinfection of the same pipe line by flushing again with water containing bleaching powder resulting in residual chlorine not less than 15mg/ltrs. after 24hrs. of such filling including laboratory testing of water samples obtain from the disinfested pipe line and disposal of water from the pipe line after completion of the work. The rates including of cost of requisite water to be arranged by the contractor) (The rate of water @Rs. 10/m3 may be recovered, if the contractor used water from deptt. source). Ref : PHED Sche. B) For uPVC/HDPE Pipe d) 90mm (OD)

e) 110 mm (OD)

Supply and delivery of CIDF sluice valve (Special type) PW-1.00 of different dia make with CI double flanged non rusting spindle sluice valves conforming to IS 14846 -2000 with latest emended having body dome/bonnet and cover of C.I.Gr-F.G 210mtr. spindle of IS-6603 G.R12/Gr-13 non-magnetic, nuts seat rings are of Gunonetal as per IS:318 LTB-2 flanges and drilled to IS:1538 Part IV & VI valves are suitable for max. working pressure of 10kg/cm2(seat test) and body tested to 15kg/cm2. N.B: The above item should be procured from the reputed manufactures as per deptt. approved vender list 100 mm dia. PN 1.0

150 mm dia. PN 1.0

Construction of different dia Sluice valve /Air valve /Washout chamber in different sizes for village road where light traffic run and for main road where heavy traffic run as deptt.approved drawing with 25cm thick brick work (1:6) over cement concrete (4:2:1) over a single B/F soling over150mm.thick sand filling in foundation including earth work in excavation and disposal of excess earth from work site with RCC (1:1.5:3) cover slab 100mm / 150mm thick slab on top of chamber with 1% reinforcement in RCC cover slab with necessary opening for operation of valve all complete including cost of labour & materials as per Departmental Dwg. [Reinforcement type:- Other manufactuerers not specified] i) 80 mm to 150 mm dia pipe

Carrying CI/DI pipes with specials and valves and lowering placing in position and laying carefully inside the trenches in proper alignment and gradient etc. including earth work in excavation of adequate width as per specification having min. clear cover from top of pipe is 1.10mtr. below existing ground level in any kind of soil including mixed with boulder, road sub-grade and its flank,but excluding moorum and laterite and stone etc.without damaging the exisiting telephone/electric cable etc.(in case of damaged if any type of cable line during excecution , necessary damaged charges as applicable by the respective authority will be borne by the agency in his own cost) preparing the bottom surface for continuous bedding of pipe line and laying pipes, fitting, fixing specials and valves with bailing out water if any including carriage of pipes, specials and valves from local deptt. store within 8KM and back filling the trenches with excavated earth in layers to original condition as per specification and direction of EIC. The surplus materials after execution of work are to be return to the deptt. store. N.B: i) Any deviation from required clear cover of 1.10mtr., due to site adverse condition, prior permission is to be obtained from the EIC in exceptional situation and payment will be made on prorate basis over the rate of entire item ii) No payment will be made without hydraulic test of the pipe line either part or full iii) The pipes, specials and valves , rubber gasket will be supplied deptt.free of cost. 150mm dia.

200 mm dia.

250 mm dia

Making rubber gasket joint to CI/DI pipes maintaining proper alignment level etc. by mechanical arrangement with or without using mobile cranes where necessary and with help of all other equipments tools and tackles etc. as required providing lubricants of approved quality and direction of EIC. (rubber gasket will be supplied deptt. free of cost 150mm dia.

200 mm dia.

250 mm dia

Carriage of different type of departmental pipes from Divisional/Sub-divisional store to the work site by truck including loading, unloading, stacking etc. including cost of fuel, lubricant and also cost of driver, helper etc. and all other taxes and charges as applicable as per direction of EICf) Above 40 Km upto 50 Km

g) Above 50 Km (Extra cost per Km) Extra 50 Km(2nos Truck x 45 Km Each = 90Km)

Providing FHTC from the existing CI/DI/UPVC/HDPE/GI/AC distribution pipeline by installing 10mm NB Gun-metal Ferrule conforming to IS 2692:1989 with latest amendments on the said pipeline with supply, fitting and fixing all other accessories like saddle piece of required size to fit the existing distribution pipeline,specials,nut & bolts,rubber sheet,washers etc. and supply & laying of 15mm NBPVC (Schedule 80) / 20mm OD HDPE (PE 100, PN 16) /20mm OD PPR-C ( Class SDR 7.4/PN16) pipes upto required length with all necessary specials 1.0 metre below the ground connecting the ferrule including cutting trenches in all sorts of soil and filling up trenches as per direction of the Engineer -in-Charge and upto a point just inside the premises of the household or asdirected by E.I.C. Supply and installation of a 15mm dia,alloy iron Bib Cock (tested to 21kg/cm2)above 1.0 Mtr.from ground,an alloy Stop Cock of 15 mm dia. with brass spindle (tedted to 21 kg/cm2) to be fitted in a position as directed by E.I.C. GI pipe of TATA Make (medium duty) of 2m length with all necessary specials to continue from the end of the PVC/HDPE/PPR-C pipe and upto 1.0 m above ground within the premises of household. Note : 1. PVC pipe shall of schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI pipe as per IS: 1239(part-I). 2. PPR-C ( Poly propylene Random copolymer) pipe shall be 3 layer confirming toIS-15801 UV stabilised & anti-microbial fusion welded,having thermal stability for hot & cold water supply including all PP-R plain& brass threated polyprolene random fittings. 3. Rateis exclusive of supply & delivery of 10mm NB gun-metal Ferrule. a) Upto 10m Length

b)Above 10m upto 20m length

Collection of household details as per prescribed format through Mobile app/Hard copies including Geo referance as directed by E.I.C and submission of the same to the P.H.E. Dte. In soft copies.

Add GST @18% on sum of Item No. 1 to 33

Add Cess @1% on sum of Item No. 1 to 34