Public Health Engineering Department Tender

Cement Concrete with graded jhama khoa (30 mm size) excluding shuttering. a) 6:3:1 proportion in ground floor.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor). i)    With 6:1 Cement mortar.

a)       20 mm thick to inside wall

b) 15 mm thick plaster at outside wall

Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powered earth or local sand.

Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening ofconcrete surface and application ofcement slurry before flooring works using cement @ 1.75kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement

i) 35mm thick.

Neat cement punning average 1.5mm thick in wall, dado,window, ceiling, floor, drain etc. NOTE:Cement 0.152 cu.m per100 sq.m.

a)Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Painting with best quality synthetic enamel paint of approved made and brand including smoothening surface by sand, paperingetc.including using of approved putty etc. on the surface if necessary. a)   On timber or plastered surface with other than hi gloss of approved quality. I) two coats. (With any shade except white)

b) On steel or other metal surface with other than hi gloss of approved quality. I) 2 coats.(With any shade except white)

Acrylic Distemper to interior wal, ceilng with a coat of solvent based interior grade acrylic primer (as per manufacturer's specifcation) including cleaning and smothning of surface i) Two Coats

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. a) Two Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground Flor: a) Two coat. a) Normal Acrylic Emulsion

Wood work in door and window frame fitted and fixed in complete including a protective cost of painting at the the contract surface of the frame excluding cost of concrete, iron but hinge and MS clamp (The quantum should be concreted upto three decimals) a)       Sal (Local)

Panel shutter for door and window as per design (Each panel consisting of single plank without joint) including fitting and fixing the same in position but excluding the cost of hinge and other fitting in Ground floor (in case of non supply of single plank, panel rate of reduction of 20% will be made) ii)  35 mm thick with 19mm thick panel. of size 30 to 45cm. a) Gamar/Champ/Badam/Bhola/Hallak

Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) of size 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut at junction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mm M.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to be provided as gap insert. The door frame to be fixed with wall by using 8mm dia. and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos. screws to be provided for each vertical member & 2 nos. for horizontal member all complete as per direction of Engineer-in-Charge. (a) Plain Colour.

Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular 'L' shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete.

Supplying, fitting and fixing bib cock or stop cock i) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent) 15 mm

Add @18% GST Rs.

Add @1% Cess Rs.