Public Health Engineering Department Tender

Making plain cement concrete (1:2:4) support of 100 mm dia (0.6m below GL and 0.3m above GL) for fixing 15mm dia GI pipe for FHTC or as per direction of Engineer-in- Charge.

Making village road (Average 3m width) crossing by horizontal Augor-boring for accomodation of laying of avarage 3(three) nos 15 mm dia. G.I. pipes for FHTC or as per direction of EIC. (30 % Total number of House hold) X 3 M

Dismantling all type of plain cement concrete works, stacking serviceable materials of site and removing rubbish as directed within a lead of 75mtr. for laying all dia pipe line in ground floor, upto 150mm thick.

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (c) Pakur Variety

Supplying, laying, fiting, fixing and jointing of UPVC pipes conforming to IS:4985-2000 with latest revision and amendments, if any, withnecessary UPVC/CI specials, CIDF sluice valves, as per relevant I.S. specification including labour charges for earth work in excavation in any kind of soil including mixed soil with boulder ,road sub-grade and its flanks but excluding moorum and laterite or sand stonehard arock including cutting of brick payment without damaging the existing telephone/electrical cable line etc.(in case of damage of any type of cable line during excavation, necessary damaged charges as applicable by the respaective authority will be borne by the agency in his own cost. Loading, unloading, carrying of pipes, specials, valves from the local store to work site and lowering laying of pipes specials valves carefully in trenches maintaining proper levels and alignment ,jointing the pipe and specials including supplying of good quality/approved brand solvent cement (as per IS:14182-1994 including cost of all fabricated PVC fitting i.e. tees,bend, reducers, adopter etc.as per IS:101- 1988 and making flange joints including supplying required quantity of nuts, bolts and rubber insertion (CIDF sluice valves will be supplied by the department free of cost) as required at site by adopting suitable method so as to facilate the maintenance of pipe line locally as per conventional method including back filling the trenches with good earth obtained from excavation of trenches including consolidation with watering in layer not exceeding 150mm thk. with maintaining an average depth of cushion of 1.10mtr. from the top of pipe line including making interconnection with distribution pipes etc. all complete as per drawing N.B. i) Manufacturer’s test certificate for UPVC pipe & specials to be produced before laying of pipe line. ii) 3rd party inspection of UPVC pipe & specials to be done by CEPET or (India) SGS/NTH Kolkata or as per direction of EIC as per approved vender list. iii)No part payment at any stage on account of supply of materials shall be entertained. iv)Payment will be made on actual consumption of materials. v) UPVC pipes for the works to be supplied as per approved vendor list and as per direction & satisfaction of EIC. No pipes will be allowed beyond recommendated vendor list. vi) Submission of drawing of pipe line with statement of materials consumed between node to node points against each R.A. & final bill.if so. vii) Any deviation from required clear cover of 1.10mtr.due to site adverse condition, prior permission is to be obtained from EIC and payment for such work will be made on prorate basis over the rate of entire item. viii)All pipe connection shall be completed in all respect and as per directionof EIC. Decision of EIC in this respect is final & binding. In case of any deviation/or any left out pipe connections an amount of Rs.10,000.00 for each pipe connection will be realized/recovered from the bill. Pressure Rating : Class - III Laying of pipe line including cost of pipe & fittings/specials & excluding cost of valve. (i) 75 mm dia (OD) UPVC

(ii) 90 mm dia (OD) UPVC

(iii) 110 mm dia (OD) UPVC

(iv) 125 mm dia (OD) UPVC

(v) 160 mm dia (OD) UPVC

Filling the pipe line with water, testing hydraulically as per I.S 3114-1965 (Article-6) in section of a length not exceeding 500mtr. for head of pressure as per specification including supplying installing and fixing all equipments such as diesel pump set, blank flange, pressure gauge, valve, pressure pump and all other tools and plants including drilling topping and plugging of necessary holes to pipes, blocking ends providing temporary thrust block and subsequent blocking of holes and other jointing materials and dismantling and removal of the same including disposal of water etc. all complete as per specification and direction of EIC. The rate is inclusive of cost of requisite water to be arranged by the contractor (Recovery rate of water @ Rs.10.00/m3, if contractor used water from deptt. source). For UPVC/HDPE Pipe (i) 75 mm dia (OD) UPVC

(ii) 90 mm dia (OD) UPVC

(iii) 110 mm dia (OD) UPVC

(iv) 125 mm dia (OD) UPVC

(v) 160 mm dia (OD) UPVC

Cleaning thoroughly the inner surface of pipe line including specials and valves by flushing with water and subsequently disinfection of the same pipe line by flushing again with water containing bleaching powder resulting in residual chlorine not less than 15mg/ltrs. after 24hrs. of such filling including laboratory testing of water samples obtain from the disinfested pipe line and disposal of water from the pipe line after completion of the work. The rates including of cost of requisite water to be arranged by the contractor) (The rate of water @Rs. 10/m3 may be recovered, if the contractor used water from deptt. source). For UPVC/HDPE Pipe (i) 75 mm dia (OD) UPVC

(ii) 90 mm dia (OD) UPVC

(iii) 110 mm dia (OD) UPVC

(iv) 125 mm dia (OD) UPVC

(v) 160 mm dia (OD) UPVC

Supply and delivery of CIDF sluice valve (Special type) PW-1.00 of different dia make with CI double flanged non rusting spindle sluice valves conforming to IS 14846 -2000 with latest emended having body dome/bonnet and cover of C.I.Gr-F.G 210 mtr. spindle of IS-6603 G.R12/Gr-13 non-magnetic, nuts seatrings are of Gun metal as per IS:318LTB-2 flanges and drilled to IS:1538 Part IV &VI valves are suitable for max working pressure of 10 kg/cm2 (seat test) and body tested to 15kg/cm2. N.B: The above item should be procured from the reputed manufactures as per deptt. approved vender list i) 150 mm dia

ii) 100 mm dia

iii) 80 mm dia

Making flange joint to DI/CI pipes, specials and valves where necessary with supply of required rubber insertion and nut bolts, washers etc. of approved quality and type all complete as per specification and direction of EIC (Nut and bolts shall be of TATA/GKW) i) 150 mm dia

ii) 100 mm dia

iii) 80 mm dia

Construction of different dia Sluice valve /Air valve /Washout chamber in different sizes for village road where light traffic run and for main road where heavy traffic run as deptt.approved drawing with 25cm thick brick work (1:6) over cement concrete (4:2:1) over a single B/F soling over150mm.thick sand filling in foundation including earth work in excavation and disposal of excess earth from work site with RCC (1:1.5:3) cover slab 100mm / 150mm thick slab on top of chamber with 1% reinforcement in RCC cover slab with necessary opening for operation of valve all complete including cost of labour & materials as per Departmental Dwg. [Reinforcement type:- Other manufactuerers not specified] 80 mm to 150 mm dia pipe

For exixting FHTC: For exixting FHTC with ferrule connection, Reflexing of exixting ferrule with fitting in the proposed distribution pipe line and supply, fitting & fixing of all other accerorise like saddle picec of required size to fit proposed pipeline specials nut & bolt rubber sheet, washer etc. including cutting trenches in all sorts of soil and filling up trenches as per direction of the EIC.

Road Restoration work by consolidating Jhama metal / Laterite chelly or stone metal / shingles of specific size hard crust to requisite thickness (measured after compaction ) in layers including screening of metals etc. as necessary, hand packing, sweeping, watering and rolling in stage with power roller to proper line.

GST @ 18%

CESS @ 1%

Rounded Off