Public Health Engineering Department Tender

Plaster ( to wall, floor , ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and racking out joints or roughening of concrete surface including throating nosing and drip course where necessary ( ground floor ) [ Excluding cost of cxhipping over concrete surface]

(ii) With Cement mortar ( 15mm thick )

b) 15 mm thick plaster 1:4

c) 10 mm thick plaster 1:4

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) c) Super Protective 100% Acrylic Emulsion.

(b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick)

(b) Priming one coat on steel or other metal surface with synthetic oil bonded primer of approved quality including smoothening surface by sand papering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc on the surface of necessary.

b) on steel or other metal surface.

i) With super gloss (Hi-gloss)

two coats (any shade except white)

Supplying Godrej Navtal lock chromium plated with latch and keys 4 levers including fitting & fixing complete.

Stripping off worn out plaster and raking out joints of walls ,celings etcupto any height and in any floor including removing rubbish within a lead of 75 mtas directed.

15 mmthk & 10 mm thk plaster= 120 +25 = 145 sqm

Dismantling all types of masonry excepting cement concrete plain or reinforced,stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.

(a) In ground floor including roof. + extra rate each addl floor ( 2 nos of floor= 50x 2= 100

Labour charge for fabrication and installation of composite door,window, partitions made from annodized extruded alloy aluminium sections for the following units:-

(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture,adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column,beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers.

ii ) 3 /4 track sliding window.

(B) Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge.

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge. (Payment will be made on finished length of the work).

(j) Fixed partitions. (Unsupported length of vertical member more than 1.5 mtr.or both ends of vertical member restrained but panels more than 0.9 Sq.m

i) Top , bottom & side member

ii) Intermediate member.

iii) Glazing clip

Add GST @18% (CGST@9%+SGST@9%)

Add Cess @1%