Public Health Engineering Department Tender

Single brick flat soling of picked jhama bricks including ramming & dressing bed to proper level & filling joints with powdered earth or local sand including cost of sand etc complete as per direction & specification. [PWD, SOR Volume-I (01.11.2017) Page-14 Item No. 1 // Corrigenda-3, Page-1]

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.Pakur variety. [Analysis of Rate as on PWD SOR Refer Annexure - XI, Item - D]

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes. Pakur variety. [Analysis of Rate as on PWD SOR Refer Annexure - XI, Item - C]

Reinforcement in reinforced conc. work in all sorts of structures includg. dist.bars, stirrups, binders etc., initial straightening and removal of loose rust (if necy.) cutting to requisite length, hooking and bending to correct shapde, placing in proper position and binding with 16 gauge balck annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundn. basement and upto roof of ground floor/up to 4m. (i) Tor steel/Mild steel. I. SAIL/TATA/RINL [PWD, SOR Volume-I (01.11.2017) Page-43 Item No. 40(a)(i)(I) // Corri-9, Page-1] a) For Raft Foundation & upto 4 mtr above G.L.

Hire and labour charges for shuttering with centering and necessary staging upto 4 mtr using approved stout props and thick hardwood planks of approved thickness with required bracing for concrete ,slabs,beams,columns,lentels curved or straight including fitting fixing and stricking out after completion of work. (b) Above 30 mm & upto 37 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. [PWD, SOR Volume-I (01.11.2017) Page-42 Item No. 36(b)]

a)For Foundation & upto 4m. above G.L Brick work with 1st class bricks in cement mortar (1:6) [PWD, SOR Volume-I (01.11.2017) Page-15 Item No. 8 // Corrigenda-3, Page-1] (a) In foundation and plinth

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. [PWD, SOR Volume-I (01.11.2017) Page-16 Item No. 16 // Corrigenda-3, Page-3]

Plaster (to wall,floor,ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating,nosing and drip course, scaffolding/ staging where necessary. (Excluding cost of chipping over concrete surface) [PWD, SOR Volume-I (01.11.2017) Page-189 Item No. 1 // Corrigenda-3, Page-49] (i) With 1:6 cement mortar (a) 20 mm thick plaster

(i) With 1:6 cement mortar (b) 15 mm thick plaster

Neat cement punning about 1.5 mm thick in wall, dado, window, sills, floor, drain etc. (Note-cement 0.152 cu.m. per 100 sq.m.) [PWD, SOR Volume-I (01.11.2017) Page-192 Item No. 15]

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish)or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly,complete as per manufacturer's specification and as per direction of the EIC. One Coat (This item to be done under specific instruction of the SE) .[PWD, SOR Volume-I (01.11.2017) Page-196 Item No. 8(b)]

Applying normal Acrylic emulsion paint of approved quality, after preparing the surface incl. scraping the same thoroughly (Plastered or concrete surface) as per manufacturer's specification .on new plastered surface (Two Coats) [PWD, SOR Volume-I (01.11.2017) Page-197 Item No. 17(a)]

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. III) For built up sections / srtuctural members of specified sections weighing not less than 22.5 Kg./m. [PWD, SOR Volume-I (01.11.2017) Page-99 Item No.01]

(a) Supplying, fitting galvanised 3 ply 12 gauge / 4 points line of barbed wire in fencing (holes already made in the body of the post) or fixed by staples tightening and fixing the wires in taut condition with straining bolts including the cost of cutting and of lapping joints in the wire as necessary but excluding the cost of galvanised staples,straining bolt and binding wire where necessary. [PWD, SOR Volume-I (01.11.2017), Page-219 Item No. 02(a)]

Labour for fitting wove wire or similar fencing net tightening and fixing the same to post with staples at every bar (including the cost of cutting and lapping joints in the net, the cost of staples, binding wire etc. and of labour for fixing such staples as necessary) (Payment to be made on the length of net in finished work.) (a) Net upto 1350 mm. height [PWD, SOR Volume-I (01.11.2017) Page-220 Item No.03]

Supplying galvanised straining bolts (with eye at one end with double nuts and washers) fitted and fixed complete. (i) 10 mm. dia. (a) 150 mm. [PWD, SOR Volume-I (01.11.2017) Page-220 Item No.04]

Supplying galvanised staples fitted and fixed complete. (a) 19 mm. to 25 mm. size. PWD, SOR Volume-I (01.11.2017) Page-221 Item No.05]

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. [PWD, SOR Volume-I (01.11.2017) Page-104 Item No. 13(i) // Corrigenda-3, Page-91] (ii) Grill weighing above 16 Kg./sq.mtr and above

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. [PWD, SOR Volume-I (01.11.2017) Page-200 Item No. 1(a)]

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With super gloss (hi-gloss) - iv) Two coats (with any shade except white) [PWD, SOR Volume-I (01.11.2017) Page-200 Item No. 2]

A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) (a) By fine sand. [PWD, SOR Volume-I (01.11.2017) Page-2 Item No. 4(B) // Corrigenda-5 Page-1]

Single brick flat soling of picked jhama bricks including ramming & dressing bed to proper level & filling joints with powdered earth or local sand including cost of sand etc complete as per direction & specification. [PWD, SOR Volume-I (01.11.2017) Page-14 Item No. 1 // Corrigenda-3, Page-1]

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.Pakur variety. [Analysis of Rate as on PWD SOR Refer Annexure - XI, Item - D]

Brick work with 1st class bricks in cement mortar (1:6) [PWD, SOR Volume-I (01.11.2017) Page-15 Item No. 8 // Corrigenda-3, Page-1] (a) In foundation and plinth

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes. Pakur variety. [Analysis of Rate as on PWD SOR Refer Annexure - XI, Item - C]

Add GST @ 18%

Add CESS @ 1%

INR Zero Only