Public Health Engineering Department Tender

Anti-snapping safety device for above pump by supplying suitable size. Nylone rope of required length (double) including supply of all necessary materials as required.

M.S suspention clamp with necessary nuts,bolts & washer etc. suitable for 50mm dia pipe ( Size 300mm x 50mm x 8mm each)

1.1 KV Grade 415 V, 2 core 10 sq.mm. PVC sheathed XLPE insulated Al. armoured cable conforming to IS:7098 (PART-1) 2011 with latest amendmends as applicable. Make :- As per approved vendor list of PHED vide no.PHE/IV/2277/W-181/19 dated 25.09.2019.with latest amendments.

50 mm dia, P.N. 1.0, CIDF Non return valve conforming to IS: 5312, part-I. Make :- As per approved vendor list of PHED vide no. PHE/IV/2277/W-181/19 dated 25.09.2019.with latest amendments.

50 mm dia, P.N. 1.0, CIDF sluice valve conforming to IS: 13095. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

50 mm dia ,PN-1.0 CIDF wafer type butterfly valve. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

50mm dia heavy type suitable length CI/MS Black pipes (for delivery header,backwash line for pump, along with necessary bends, specials, fittings , viz flanges, bolts, nuts, gaskets, concentric enlarger , MS dismenteling joint, for connecting main pipe line etc. including providing MS/Bricks/PCC support for laying of pipes, valves as required to make the installation complete .

230 V MCC cum PDB (1-3 HP with DOL, Direct Online starter) having changeover for bypass arrangement with minimum 2mm thickness and degree of protection IP-54, conforming to IS-8623 with suitable Bus bar, Digital Voltmeter Ammeter, Contactor, delay timer, MCB, Valve Actuator,starter etc. with PLC logic as detailed in attached technical specification.

LED street light luminarie IP 66 LM6-HPDC Housing Street light aerodynamically designed with better thermal management/ Potted driver is to be provided,the luminaire and housing should be from the same manufacturer(cat no- BRP052 LED 045 CW SLMR FG S1 PSU GR ,System Efficacy greater than 100 lumen/watt) Make-Philips OR Equivalent and same techinal specification of Havells.The manufacturer has to provide LM79/LM80 reports corresponding to the luminaire/LED Chip along with type test Certificate.Respectively the luminaire manufacturer should have an in house NABL Accredited testing facility.

63 Amp,10 kA, 240/415V, 50 Hz Double pole MCB conforming to IS / IEC: 60947-3, "C" characteristics with enclosure. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

6-32Amp,10 kA, 240/415V, 50 Hz SP MCB conforming to IS / IEC: 60898-1, "C" characteristics. (10Amp-1 no,16Amp-1no) Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

10 Amp,10 kA, 240/415V, 50 Hz SPN MCB conforming to IS / IEC: 60898-1, "C" characteristics. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

6 way SP&N Double Door horizontal Distribution Board (I/C 2 + O/C 4) conforming to IS 13032 & IS 8623 and IP42/43. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

63 Amp, 240V, 50 Hz Double pole main switch conforming to IS / IEC: 60947-3, "C" characteristics with enclosure. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

63 Amps,4 Way Wall mounted Busbar chember. Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

63 Amp, 240/415 V Porcelain fuse unit (Base & Bridge) Make :- As per approved vendor list of PHED vide no. 8864/79/F/2018 dated 28.06.2024 with latest amendments.

Hard wooden board (450mm X 304.8 mmx 25 mm thick)

Installation of item Laying of cable on wall/surface incl. S & F of MS saddles with earthing attachment in 10 SWG GI (Hot Dip) wire, making holes etc. as necy. mending good damages and painting all complete as per direction of E.I.C.

Supplying and fixing of compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of cable .all complete as per direction of E.I.C.

Finishing the end of cable by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials all complete as per direction of E.I.C.

Making internal wiring/electrification of the Pump house by (2x 22/0.3 (1.5 sqmm) + 1x 22/0.3 (1.5 sqmm) single core PVC insulated multistrand FRLSH Grade flexible copper wire through 20 mm PVC conduit pipe/casing by supplying one no. 40 Amp, 10kA, 240/415V,50 Hz SPN/DP MCB Isolator conforming to IS / IEC: 60947-3, "C" characteristics. (As per approved vendor list of PHED vide no. PHE/IV/2277/W-181/19 dated 25.09.2019) with required module PVC Board & piano key type switch. (ave. run 6 mtr). i) LED Tube set point-2 nos., Bulk Head light point- 1 no., 5 pin 6 Amps. Plug point- 1 no., 16 Amp socket & switch- 1 no, indicator- 1 no. each, with necy. earthing arrangement & one fan point (Total point 6 nos. points) including drawing power by suitable gauge (2.5 mm2) of copper wire from installed cut-out to SPN/DP MCB within DB through 20 mm PVC casing capping (precision make) as per direction of EIC (fittings should be of Philips make & wiring should be with continuous earthing arrangement and 20W two nos. 4 ft long LED tube light sets PHILIPS Astra Line, one no. bulk head (Endura WT202W LED6S NW PSU S2 PC), one no. 0-4 step fan regulator (Humfree), fittings etc to be supplied by agency).

Installation, testing & commisioning of above supplied (as in item no. 1 to 5, 7 to 20), MCC,valves etc by jointing submersible cable within the tubewell situated outside the pump house by making derrick arrangement by assembling the column pipes properly and fitting, fixing the pressure gauge, depth gauge, air pipe etc. in position and erection of delivery line & wash out line with the C.I specials and Tee including mending damages goods etc. all complete as per direction. This also includes the charges for laying submersible cable from tubewell to control panel by underground and saddle on wall and connection with required feeder of panel all complete.

Making suitable size pump foundation base ( Size: 1.00 mtr. x 1.00 mtr. x 1.5 mtr.) with supplying cement, sand, stone chips etc. in the portion of (1:2:4) including plastering, neat cement finishing including painting etc. all Complete as per direction of EIC. (i) Tubewell outside pump house

Making required nos. of brick pillar 0.25 mtr. X 0.25 mtr. For supporting of valves and pipes with 12 mm thick plaster and net cement finish including painting complete.

S&F of 3" dia 1.5 mt minipole with baseplate to be fixed on rooftop incl. S&F of 1.5 mtr long arm bracket (removable type) incl. CC (6:3:1) muffing (450X450X600) with 3 mm thick neat cement finish & painting incl. S&F of 200x150x100 mm 16 SWG GI loop box with necessary power connection by 3x 22/0.3 (1.5 Sq.mm) (2 nos. P&N and 1 no. ECC) 'FRLSH' PVC insulated & unsheathed copper wire (Approved make) in 20 mm size PVC rigid conduit 'FRLSH' (Precision make) incl. necy. fittings as required as per direction of EIC. (for 12m length @ 102/mtr.)

(a) Earthing with 50 mm ISI mark medium diameter G.I. pipe 3.64 mm thick x 3Mtr. (10ft.) long and 1 x 4 SWG G.I. wire (4Mtr.long) 13 mm diameter x 80mm (3inch) long G.I. Bolts, double nuts, washer including S & F of 15mm diameter G.I. pipe protection (1 Mtr. Long) to be filled with bitumen partly below ground level to an average depth of 3.65Mtr.(12ft.) below the ground level and restoring the surface duly rammed. i) For soft soil by ISI Medium GI pipe.

(b) Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe.

(c) Extra for treatment of soil by salt and charcoal coke for pipe electrode.

(d) Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.Length of busbar is 0.5 mtr.

(e) Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc.

Add GST @ 18 %

Add Cess @ 1 %