Public Health Engineering Department Tender

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats (Ref No- PWD BUILDING WORKS SCHEDULE-2017,Page No-196,Item No-10 )

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) b) Premium 100% Acrylic Emulsion ( Ref no- PWD BUILDING WORKS SCHEDULE-2017,Page No-197,Item No-17.a )

Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. (ii) 550 mm X 400 mm size ( Ref no- S&P SCHEDULE-2017,Page No-41,Item No-2(ii) )

Supplying, fitting and fixing 10 litre porcelain low-down cistern of approved make with either side or bottom inlet, side overflow, brackets complete with all internnal PVC fittings.White (Ref no- S&P SCHEDULE-2017,Page No-41,Item No-2(ii) )

Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm ( Ref No- S&P SCHEDULE-2017,Page No-82,Item No-19 )

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only).50 mm dia ( Ref No- S&P SCHEDULE-2017,Page No-5,Item No-5.iv )

Supplying, fitting and fixing bib cock or stop cock.(c) (i) Chromium plated Bib Cock (angular shape with wall flange) (Equivalent to Code No. 5037 & Model - Florentine of Jaquar or similar brand). ( Ref No- S&P SCHEDULE-2017,Page No-6,Item No-7.C)

Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. (a) With 'P' trap (with vent) (Ref No:- S&P SCHEDULE-2017,Page No-79,Item No-3.a )

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (d) Sal : Local. (Ref No- PWD B.W 2017, PG No-114, SL No-1)

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. (In case of non-supply of single plank, penal rate of reduction of 20% will be made)(a) Ordinary Teak Wood. (Ref No- PWD B.W 2017, PG No-117, SL No-1.III.C)

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.(Add extra @ 1% for each addl. floor upto 4th floor and @ 1.25%for each addl. floor above 4th floor) ii) Grill weighing above 16 Kg./sq.mtr and above (Ref No- PWD Schedule Building Page No-104 Item No-13(ii))

Supplying, fitting and fixing clear visioned, Insulated Double Glazed two track sliding Aluminium window (U-value 3.2W/m 2 K) made up with 6 mm thick toughened glass (wt 15kg/m 2 ) with 12 mm air gap in between, containing perforated Al/ structural foam spacer filled with moisture absorbant dessicant at all sides duly sealed with primary sealant (polyisobutylene) and affixed inside multi cellular/ multi chember profiles of required section made of Alluminium alloy extrusions conforming to IS:733-1983 and IS:1285 - 2002 annodised/powder coated with (required film thickness and specified colour /natural) matt finished conforming to IS: 1868-2006/ IS: 13871-2002 measured as per IS:6012-1992, and sealed appropriately with secondary (polysulphide/silicon) sealant all junctions complete in all respect as per direction and satisfaction of Engineer-in-Charge including all incidental charges. (Payment shall be made on finished size of Aluminium window including frame.) ( Ref No- Volume I, P-293 I- 21

Withdrawing the existing PCC pole after dismantling LTOH accessories from the PCC pole and staging pole as per direction of the EIC [ Total =70 Nos pole]

Transportation of the PCC pole from Sea Beach (extension part) to 5 No Sea Beach to different Stag yard